1996 TOYOTA TERCEL instrument panel

DI4M8-01
N12263
Front Passenger
Airbag Assembly Steering Wheel Pad
(With Airbag)
Spiral Cable
Airbag Sensor Assembly
Instrument Panel
Junction BlockSRS Warning Light
DI-152
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TERCEL (RM440U)
PARTS LOCATION

DI4MR-02
N20816
BatteryEngine Room
Relay BlockInstrument Panel
Junction BlockTheft Deterrent ECU
+B1
T41
1D8
1K11
L-Y L-Y
2
MAIN FL
EA2BDOME 1
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-197
1996 TERCEL (RM440U)
CIRCUIT INSPECTION
ECU Power Source Circuit (w / Theft deterrent System)
CIRCUIT DESCRIPTION
This circuit provides power to operate the theft deterrent and door lock ECU.
WIRING DIAGRAM

N20817
BatteryInstrument Panel
Junction BlockTheft Deterrent ECU
(Door Lock Control Relay)
1J2
W-G
MAIN FLEA2
F7 F6 221A3
D6 (8)
T39
D6 (16)
T34
A A
IEJ3
JUNCTION
CONNECTOR A
AW-B
ALT AM1POWER
2 1L
W-B B W-G
( ): w/o Theft Deterrent System+B2
(B)
E
B-R B-R2JUNCTION
CONNECTOR J6
J/B No.2
11J/B No.7 DI-200
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
1996 TERCEL (RM440U)
Actuator Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power to drive the door lock motor.
WIRING DIAGRAM
DI4MS-01

N20822
Battery MAIN FL 1
F6 F7ALT B-R
Taillight
LH Taillight
RH 2
EA2B-R
G 1J1Instrument Panel Junction Block
Taillight Control Relay
TAIL4
1E
8
1L
G G LGTheft Deterrent ECU
23
T4 TAIL
1
B
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
DI-235
1996 TERCEL (RM440U)
Taillight Control Relay Circuit
CIRCUIT DESCRIPTION
When the theft deterrent system is activated, it causes the Tr in the ECU to switch on and off at approximately
0.4 sec. intervals. This switches the taillight control relay on and off, thus flashing the taillights (See the wiring
diagram below).
In this condition, if any of the following operations is done, the Tr in the ECU goes off and the taillight control
relay switches off, thus stopping the taillights flashing:
(1) Unlock the front LH or RH door with key.
(2) Turn the ignition switch to ACC or ON position.
(3) Unlock the doors with the wireless door lock control system.
(4) Wait for approximately 60 seconds.
WIRING DIAGRAM
DI4N9-01

N20823
BatteryMAIN FL2
F61
F7B-R B
Fusible Link
Block2
EA2B-R 2 2AM1
W-G 2 1
1B
1J W-G2Ignition Switch
3
B-Y4
1BCIG & RAD1
1DGRTheft Deterrent ECU
8
T3
ACC
I10Instrument Panel
Junction Block
Instrument Panel
Junction BlockACC
AM1
ALT
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
DI-237
1996 TERCEL (RM440U)
Ignition Switch Circuit
CIRCUIT DESCRIPTION
When the ignition switch is turned to the ACC position, battery positive voltage is applied to the terminal ACC
of the ECU. Also, if the ignition switch is turned to the ON position, battery positive voltage is applied to the
terminals ACC and IG of the ECU. When the battery positive voltage is applied to the terminal ACC of the
ECU while the theft deterrent system is activated, the warning stops. Furthermore, power supplied from the
terminals ACC and IG of the ECU is used as power for the door courtesy switch, and position switch, etc.
WIRING DIAGRAM
DI4NA-02

N12877N14677I09780
Instrument Panel Junction Block
CIG & RAD
BE4061I05896I09781
ON
IG
(+) (-)
Disconnect
DI-238
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check CIG / RAD fuses.
PREPARATION:
(a) Remove the fuse box cover.
(b) Remove CIG & RAD fuse from instrument panel junction
block.
CHECK:
Check continuity of CIG & RAD fuses.
OK:
Continuity
NG Check for short in all the harness and compo-
nents connected to the CIG & RAD fuse (See at-
tached wiring diagram).
OK
2 Check voltage between terminals ACC of theft deterrent ECU and body ground.
PREPARATION:
(a) Disconnect the theft deterrent ECU connectors.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals ACC of theft deterrent
ECU connector and body ground.
OK:
Voltage: 10 - 14 V
OK Check and replace theft deterrent ECU.
NG
Check and repair harness and connector between theft deterrent ECU and battery
(See page IN-26).

N12896
Rear LeftR-W R-W
Rear Right R-W 2
1 Security Diode1
R-W
Instrument Panel
Junction Block11
1L6
1CR-W3
T4 CTY Front Right1
(2Dr) R
(4Dr) R-G8
IE2R-G19
T4 DSWP Door Courtesy Switch
Front Leftto Door Light
11
IE2R7
T4DSWD Theft Deterrent ECU
F8
F9
11
R11R12 R DI-244
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
1996 TERCEL (RM440U)
Door Courtesy Switch Circuit
CIRCUIT DESCRIPTION
The door courtesy switch goes on when the door is opened and goes off when the door is closed.
WIRING DIAGRAM
DI4ND-01

P19552
TOYOTA Hand-Held Tester
DLC3EM0K9-03
P20244
- ENGINE MECHANICALIGNITION TIMING
EM-9
430 Author
: Date
:
1996 TERCEL (RM440U)
IGNITION TIMING
INSPECTION
1. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
2. CONNECT TOYOTA HAND-HELD TESTER OR OBDII
SCAN TOOL
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand-held tester or OBDII scan
tool to the DLC3.
(c) Please refer to the TOYOTA hand-held tester or OBDII
scan tool operator's manual for further details.
3. CONNECT TIMING LIGHT
4. INSPECT IGNITION TIMING
(a) Using SST, connect terminals TE1 and E1 of the DLC1.
SST 09843-18020
(b) Using a timing light, check the ignition timing.
Ignition timing:
10° BTDC @ idle
(w/ Cooling fan OFF and transmission in neutral
position)
(c) Remove the SST from the DLC1.
SST 09843-18020
5. FURTHER CHECK IGNITION TIMING
Check that the ignition timing advances.
Ignition timing:
7 - 17° BTDC @ idle
(w/ Cooling fan OFF and transmission in neutral posi-
tion)
HINT:
The timing mark moves in a range between 7° and 17°.
6. DISCONNECT TIMING LIGHT
7. DISCONNECT TOYOTA HAND- HELD TESTER OR
OBDII SCAN TOOL