1996 TOYOTA TERCEL water pump

IN0CI-02
IN-36
- INTRODUCTIONTERMS
1996 TERCEL (RM440U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE-J1930 terms and abbreviations used in this manual in compliance with SAE rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOTA TERMS
( )--ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal-
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection-
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position-
CTOXContinuous Trap Oxidizer-
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition-
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode-
ECLEngine Control Level-
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control-
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory-
FEPROMFlash Erasable Programmable Read Only Memory-
FFFlexible Fuel-
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)

PP192-01
PP-18
- PREPARATIONCOOLING
1996 TERCEL (RM440U)
SSM (Special Service Materials)
08826-00100Seal Packing 1282B,
THREE BOND 1282B or equivalent
(FIPG)Water pump

SS0N6-04
SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Cylinder head cover x Cylinder head7.07061 in.´lbf
No. 2 idler pulley x Cylinder head2828020
Camshaft timing pulley x Camshaft5151037
No. 1 idler pulley x Cylinder block18.518513
Crankshaft pulley x Crankshaft1551,55011 2
No. 2 crankshaft pulley x Crankshaft pulley1919514
RH engine mounting insulator x RH engine mounting bracket6465047
RH engine mounting insulator x Body7374054
No. 1 engine hanger x Cylinder head2121015
No. 2 engine hanger x Cylinder head5353038
Cylinder head x Cylinder block 1st
2nd45
Turn 90°450
Turn 90°33
Turn 90°
Camshaft bearing cap x Cylinder head131309
Intake manifold x Cylinder head19.519514
Intake manifold stay x Intake manifold2020015
Intake manifold stay x Cylinder block2020015
Exhaust manifold x Cylinder head4848035
Exhaust manifold stay x Cylinder block4040029
Exhaust manifold stay x Exhaust manifold4040029
Exhaust manifold heat insulator x Exhaust manifold8.08069 in.´lbf
Water outlet housing x Cylinder head3030022
Camshaft position sensor x Cylinder head8.08069 in.´lbf
EGR VSV x Cylinder head17.517513
EGR valve x Cylinder head17.517513
EGR pipe x EGR valve4040029
EGR pipe x Intake manifold3030022
PS ump bracket x Cylinder head4344032
Fuel inlet hose x Fuel filter2930022
Front exhaust pipe x Exhaust manifold6263049
Connecting rod cap x Connecting rod4040029
Crankshaft bearing cap x Cylinder block5858042
Rear oil seal retainer x Cylinder block7.57565 in.´lbf
Oil filter union x Cylinder block2525018
Oil pressure switch x Cylinder block131309
RH engine mounting bracket x Cylinder block5959043
Knock sensor x Cylinder block4545033
Generator bracket x Cylinder block2424018
Rear end plate x Cylinder block101007
Flywheel x Crankshaft9090065
Drive plate x Crankshaft9090065
Drive plate x Torque converter clutch2525018
A/C compressor bracket x Cylinder block2728020
PS pump adjusting strut x Cylinder block2121015

SS0NA-03
SS-14
- SERVICE SPECIFICATIONSCOOLING
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Drain plug x Cylinder block2525018
Water pump x Cylinder block17.517513
Oil dipstick guide x RH engine mounting bracket18.518514
Water inlet pipe x Cylinder block7.57565 in.´lbf
Intake manifold stay x Cylinder block2020015
Water inlet x Water outlet housing5.05043 in.´lbf
Radiator upper support x Body121209
Oil cooler x Radiator lower tank Nut A
Nut B, C15.0
8.5150
8511
75 in.´lbf
No. 1 cooling fan x Radiator7.07061 in.´lbf
No. 2 cooling fan x Radiator7.07061 in.´lbf

EM0K6-01
EM0126
No!
P20576
EM3385
- ENGINE MECHANICALTIMING BELT
EM-15
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT TIMING BELT
NOTICE:

Do not bend, twist or turn the timing belt inside out.

Do not allow the timing belt to come into contact with
oil, water or steam.

Do not utilize timing belt tension when installing or re-
moving the mounting bolt of the camshaft timing
pulley.
If there are any defects as shown in the illustration, check these
points:
(a) Premature parting

Check for proper installation.

Check the timing cover gasket for damage and
proper installation.
(b) If the belt teeth are cracked or damaged, check to see if
either camshaft or oil pump is locked.
(c) If there is noticeable wear or cracks on the belt face,
check to see if there are nicks on the side of the idler
pulley lock.
(d) If there is wear or damage on only one side of the belt,
check the belt guide and the alignment of each pulley.
(e) If there is noticeable wear on the belt teeth, check the tim-
ing belt cover for damage and check gasket has been
installed correctly and for foreign material on the pulley
teeth.
If necessary, replace the timing belt.
2. INSPECT IDLER PULLEYS
(a) Visually check the seal portion of the idler pulley for oil
leakage.
If leakage is found, replace the idler pulley.
(b) Check that the idler pulley turns smoothly.
If necessary, replace the idler pulley.

P20556
P20558
P20535
Tension
P20555
EM-18
- ENGINE MECHANICALTIMING BELT
1996 TERCEL (RM440U)
(b) Using the crankshaft pulley bolt, turn the crankshaft and
align the timing marks of the crankshaft timing pulley and
oil pump body.
6. INSTALL TIMING BELT
NOTICE:
The engine should be cold.
HINT:
When re-using timing belt:
Align the points marked during removal, and install the belt with
the arrow pointing in the direction of engine revolution.
(a) Remove any oil or water on the pulleys, and keep them
clean.
NOTICE:
Only wipe the pulleys; do not use any cleansing agent.
(b) Install the timing belt, and check the tension between the
crankshaft timing pulley and camshaft timing pulley.
7. CHECK VALVE TIMING
(a) Loosen the No.1 idler pulley mount bolt, until the pulley is
moved slightly by the spring tension.

EM0JQ-06
EM9411
EM9412
P20480
SST
P20478
SST
P20477
12 mm
Hexagon
Wrench EM-70
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
DISASSEMBLY
1. M/T:
REMOVE CLUTCH COVER AND DISC
2. REMOVE FLYWHEEL (M/T) OR DRIVE PLATE (A/T)
3. REMOVE REAR END PLATE
4. INSTALL ENGINE TO ENGINE STAND FOR DIS-
ASSEMBLY
5. REMOVE TIMING BELT AND PULLEYS
6. REMOVE CYLINDER HEAD
7. REMOVE OIL DIPSTICK GUIDE AND GENERATOR
ADJUSTING BAR
8. REMOVE WATER PUMP WITH WATER INLET PIPE
9. REMOVE GENERATOR BRACKET
10. REMOVE KNOCK SENSOR
Using SST, remove the knock sensor.
SST 09816-30010
11. REMOVE RH ENGINE MOUNTING BRACKET
12. REMOVE OIL FILTER
13. REMOVE OIL PRESSURE SWITCH
Using SST, remove the oil pressure switch.
SST 09816-30010
14. REMOVE OIL PUMP AND PRESSURE REGULATOR
VA LV E
15. REMOVE OIL FILTER UNION
Using a 12 mm hexagon wrench, remove the oil filter union.

P20750
P20480
SST
P20545
EM9412
EM7333
EM-90
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
15. INSTALL RH ENGINE MOUNTING BRACKET
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
16. INSTALL KNOCK SENSOR
Using SST, install the knock sensor.
SST 09816-30010
Torque: 45 N´m (450 kgf´cm, 33 ft´lbf)
17. INSTALL GENERATOR BRACKET
Torque: 24 N´m (240 kgf´cm, 18 ft´lbf)
18. INSTALL WATER PUMP WITH WATER INLET PIPE
19. INSTALL OIL DIPSTICK GUIDE AND GENERATOR AD-
JUSTING BAR
20. INSTALL CYLINDER HEAD
21. INSTALL TIMING BELT AND PULLEYS
22. REMOVE ENGINE STAND
23. INSTALL REAR END PLATE
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
24. M/T:
INSTALL FLYWHEEL
(a) Apply adhesive to 2 or 3 threads of new mounting bolt
end.
Adhesive:
Part No. 08833-00070, THREE BOND 1324 or
equivalent