1996 TOYOTA TERCEL belt

N10070
Fall Length minus
200 mm (7.87 in.)
BO0635
BO-58
- BODYSEAT BELT
1996 TERCEL (RM440U)
(e) Retract the whole belt, then pull out the belt until 200 mm
(7.87 in.) of belt remains retracted.
(f) Tilt the retractor slowly.
(g) Make sure that the belt can be pulled out at a tilt of 15 de-
grees of tilt.
If a problem is found, replace the assembly.
4. Manual Type:
TESTING
(a) Adjust the belt to the proper length.
(b) Apply a firm load to the belt.
(c) Make sure that the belt does not extend.

AC1HH-04
AC-16
- AIR CONDITIONINGTROUBLESHOOTING
1168 Author
: Date
:
1996 TERCEL (RM440U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
No blower operation
2. Heater main relay
3. Blower motor
4. Blower resistor
5. Blower speed control switchAC-62
AC-55
AC-56
AC-71
No air temperature control1. Inspect engine coolant volume
2. A/C control lever-
AC-72
No compressor operation
1. Refrigerant volume
2. A/C Fuse
3. Magnetic clutch relay
4. Magnetic clutch
5. Compressor
6. Pressure switch
7. Heater main relay
8. A/C switch
9. Blower speed control switch
10.A/C amplifier
11. Thermistor
12.Wiring and wiring connectionsAC-3
-
AC-63
AC-40
AC-36
AC-59
AC-59
AC-62
AC-71
AC-66
AC-57
-
Compressor operates intermittently
1. Refrigerant volume
2. Refrigerant cooling system
3. Pressure switch
4. A/C amplifier
5. Thermistor
6. Wiring and wiring connectionsAC-3
-
AC-59
AC-66
AC-57
-
No condenser fan operation
1. Condenser fan fuse
2. Engine main relay
3. Cooling fan relay No.1
4. Cooling fan relay No.2
5. Cooling fan relay No.3
6. Magnetic clutch relay
7. Condenser fan motor
8. Pressure switch
9. Water temperature switch
10.A/C amplifier-
CO-33
AC-64
AC-64
AC-64
AC-63
AC-65
AC-59
-
AC-66
No cool air comes out
1. Refrigerant volume
2. Drive belt
3. Magnetic clutch
4. Compressor
5. Refrigeration controlAC-3
AC-18
AC-40
AC-36
-
Cool air comes out intermittently
1. Refrigerant Volume
2. Drive belt
3. A/C amplifier
4. Expansion valve
5. Evaporator
6. Thermistor
7. Wiring and wiring connectionAC-3
AC-18
AC-66
AC-54
AC-52
AC-57
-
Cool air comes out only at high engine rpm
1. Refrigerant volume
2. Drive belt
3. Inspect refrigerant linesAC-3
AC-18
-

- AIR CONDITIONINGTROUBLESHOOTING
AC-17
1169 Author
: Date
:
1996 TERCEL (RM440U) Insufficient cooling
1. Refrigerant volume
2. Drive belt
3. Refrigerant cooling system
4. A/C amplifier
5. Refrigerant lines
6. ThermistorAC-3
AC-18
-
AC-66
-
AC-57
No engine idle up when A/C switch on
1. Idle air control (IAC) valve
2. A/C amplifier
3. Wiring and wiring connections-
AC-66
-
No warm air comes out
1. Engine coolant volume
2. A/C control lever adjustment
3. Heater radiator-
AC-73
AC-31

CH0086
CorrectWrong
AC1C5-04
Z16157
PS Pump
Idle Pulley
Compressor
Compressor Crankshaft
PulleyCrankshaft
Pulley
I17366
Nippondenso Borroughs AC-18
- AIR CONDITIONINGDRIVE BELT
1170 Author
: Date
:
1996 TERCEL (RM440U)
DRIVE BELT
ON-VEHICLE INSPECTION
1. INSPECT DRIVE BELT'S INSTALLATION CONDITION
Check that the drive belt fits properly in the ribbed grooves.
2. INSPECT DRIVE BELT TENSION
Using a belt tension gauge, check the drive belt tension.
Belt tension gauge:
Nippondenso BTG-20 (95506-00020) or Borroughs
No. BT-33-73F
Drive belt tension:
New belt 160 ± 25 lbf
Used belt 100 ± 20 lbf
HINT:

ºNew beltº refers to a belt which has been used less than
5 minutes on a running engine.

ºUsed beltº refers to a belt which has been used on a run-
ning engine for 5 minutes or more.

After installing the drive belt, check that it fits properly in
the ribbed grooves.

AC1C6-03
N05463
Adjusting
Bolt
Compressor
Drive Belt
Idle Pully Lock Nut
N15502
- AIR CONDITIONINGDRIVE BELT
AC-19
1996 TERCEL (RM440U)
REMOVAL
1. w/o Power Steering:
REMOVE DRIVE BELT
(a) Loosen the idle pully lock nut.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(b) Loosen the adjusting bolt and remove drive belt.
2. w/ Power Steering:
REMOVE DRIVE BELT
(a) Loosen the 2 PS pump set bolts.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(b) Loosen the adjusting bolt.
(c) Remove the belt.

AC2WH-02
AC-20
- AIR CONDITIONINGDRIVE BELT
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal procedure (See page AC-19).

AC3IP-01
AC-38
- AIR CONDITIONINGCOMPRESSOR
1996 TERCEL (RM440U)
REMOVAL
1. RUN ENGINE AT IDLE SPEED WITH A/C ON FOR APPROX. 10 MINUTES
2. STOP ENGINE
3. DISCONNECT NEGATIVE (-) TERMINAL CABLE FROM BATTERY
4. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
5. REMOVE ENGINE UNDER COVER
6. DISCONNECT CONNECTOR FROM MAGNETIC CLUTCH
7. DISCONNECT 2 HOSES FROM COMPRESSOR SERVICE VALVE
NOTICE:
Cap the open fitting immediately to keep moisture or dirt out of the system
8. REMOVE COMPRESSOR
(a) Loosen the compressor drive belt.
(b) Remove the compressor mounting bolts and the compressor.

AC2WN-02
- AIR CONDITIONINGCOMPRESSOR
AC-39
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL COMPRESSOR WITH 4 MOUNTING BOLTS
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
2. INSTALL DRIVE BELT (See page AC-20)
3. CONNECT 2 HOSES TO COMPRESSOR SERVICE VALVES
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
HINT:
Lubricate 2 new O-rings with compressor oil and install the tubes.
4. CONNECT MAGNETIC CLUTCH LEAD WIRE TO WIRING HARNESS
5. CONNECT NEGATIVE (-) TERMINAL CABLE TO BATTERY
6. EVACUATE AIR FROM REFRIGERATION SYSTEM AND CHARGE SYSTEM WITH REFRIGERANT
Specified amount:
600 ± 50 g (21.73 ± 1.76 oz.)
7. INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak detector, check for leakage of refrigerant.
If there is leakage, check the tightening torque at the joints.
8. INSPECT A/C OPERATION