PP196-04
PP-22
- PREPARATIONLUBRICATION
1996 TERCEL (RM440U)
LUBRICANT
ItemCapacityClassification
Engine oil
Drain and refill w/o Oil filter change
w/ Oil filter change
Dry fill
2.6 liters (2.7 US qts, 2.3 lmp. qts)
2.8 liters (3.0 US qts, 2.5 lmp. qts)
3.7 liters (3.9 US qts, 3.3 lmp. qts)
API grade SH, Energy-Conserving II multigrade
engine oil or ILSAC multigrade engine oil and
recommended viscosity oil
LU08B-04
P20919
SST
LU0490
SST
- LUBRICATIONOIL AND FILTER
LU-3
1996 TERCEL (RM440U)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with mineral oil will
result in the removal of natural fats from the skin,
leading to dryness, irritation and dermatitis. In addi-
tion, used engine oil contains potentially harmful
contaminants which may cause skin cancer. Ade-
quate means of skin protection and washing facilities
should be provided.
Care should be taken, therefore, when changing en-
gine oil, to minimize the frequency and length of time
your skin is exposed to used engine oil. Protective
clothing and gloves, that cannot be penetrated by oil,
should be worn. Wash your skin throughly with soap
and water, or use waterless hand cleaner, to remove
any used engine oil. Do not use gasoline, thinners, or
solvents.
In order to preserve the environment, used oil must
be disposed of only at designated disposal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug and drain the oil into a contain-
er.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter.
SST 09228-06501
(b) Clean the filter contact surface on the filter mounting.
(c) Lubricate the filter rubber gasket with engine oil.
(d) Tighten filter until the gasket contacts seat of the filter
mounting. Then using SST, give it an additional 3/4 turn
to seat the filter.
SST 09228-06501
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
(b) Fill the engine with new oil.
Oil grade: See step 1 in oil oressure check
Oil capacity:
Drain and refill w/ Oil filter change
w/o Oil filter change2.8 liters (3.0 US qts, 2.5 lmp. qts)
2.6 liters (2.7 US qts, 2.3 lmp. qts)
Dry fill3.7 liters (3.9 US qts, 3.3 lmp. qts)
MX07F-04
Q06439
Z1891017 mm Head
Starter Set Bolt
Q06443
Q09187
Filler Plug
Oil Level
0 - 5 mm
Drain Plug MX-4
- MANUAL TRANSAXLEMANUAL TRANSAXLE UNIT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE BATTERY AND AIR CLEANER CASE AS-
SEMBLY WITH AIR HOSE
2. REMOVE CLUTCH RELEASE CYLINDER AND LINE
CLAMP
(a) Remove the 2 bolts and release cylinder.
(b) Remove the 2 bolts and release cylinder line clamp.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
3. DISCONNECT GROUND CABLE
Remove the 2 bolts and disconnect the 2 ground cables from
the transaxle side and engine left mounting bracket side.
4. DISCONNECT BACK-UP LIGHT SWITCH CONNEC-
TOR
5. DISCONNECT CONTROL CABLE
(a) Remove the 2 clips and washers.
(b) Remove the 2 clips from the cables.
6. REMOVE STARTER SET BOLT
Remove the 2 set bolts of the starter from the transaxle upper
side.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
7. REMOVE TRANSAXLE MOUNTING BOLT
Remove the 3 bolts of transaxle case upper side.
Torque:
17 mm head: 64 N´m (650 kgf´cm, 47 ft´lbf)
8. INSTALL ENGINE SUPPORT FIXTURE
9. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
10. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
11. REMOVE LH AND RH ENGINE UNDER COVERS
12. DRAIN TRANSAXLE OIL
Oil grade: API GL-4 or GL-5
Viscosity: SAE 75W-90
Capacity: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
13. REMOVE LH AND RH DRIVE SHAFTS
(See page SA-17)
