1996 TOYOTA RAV4 belt

CO0BI−03
P13480
New O−Ring
New Gasket
P15547
New O−Ring
P15464
Connect
Z16489
3
1
2 CO−8
− COOLINGWATER PUMP
1996 RAV4 (RM447U)
INSTALLATION
1. INSTALL WATER PUMP TO WATER PUMP COVER
Install a new gasket and the water pump with the 3 bolts.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
2. INSTALL WATER PUMP AND WATER PUMP COVER
ASSEMBLY
(a) Install new O−ring and gasket to water pump cover.
(b) Install a new O−ring to the water bypass pipe.
(c) Apply soapy water to the O−ring on the water bypass
pipe.
(d) Connect the water pump cover to the water bypass pipe.
Do not install the nuts yet.
(e) Install the water pump with the 3 bolts. Tighten the bolts
in the sequence shown.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
(f) Install the 2 nuts holding the water pump cover to the wa-
ter bypass pipe.
Torque: 9.3 N·m (95 kgf·cm, 82 in.·lbf)
3. INSTALL GENERATOR DRIVE BELT ADJUSTING BAR
(a) Install the adjusting bar with the bolt.
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
(b) Connect the crankshaft position sensor connector clamp.
4. INSTALL NO.2 IDLER PULLEY AND TIMING BELT
TENSION SPRING
5. CONNECT LOWER RADIATOR HOSE
6. INSTALL TIMING BELT (See page EM−20)
7. FILL WITH ENGINE COOLANT
8. START ENGINE AND CHECK FOR COOLANT LEAKS
9. INSTALL RH ENGINE UNDER COVER

EM0EI−02
S01653
21
S01367
− ENGINE MECHANICALVALVE CLEARANCE
EM−5
1996 RAV4 (RM447U)
VALVE CLEARANCE
INSPECTION
HINT:
Inspect and adjust the valve clearance when the engine is cold.
1. DISCONNECT PS RESERVOIR
2. REMOVE CYLINDER HEAD COVER
(a) Disconnect the accelerator cable from the throttle body.
(b) Disconnect the accelerator cable from the clamp on the
intake manifold.
(c) Disconnect the accelerator cable from the clamp on the
generator bracket.
(d) Disconnect the A/T throttle control cable from the throttle
body.
(e) Disconnect the PCV hose from the air cleaner hose.
(f) Disconnect the PCV hose from the intake manifold.
(g) Disconnect the high−tension cords from the spark plugs.
(h) Remove the 2 bolts, and disconnect the accelerator cable
bracket from the intake manifold.
(i) Disconnect the engine wire protector from the 2 mounting
bolts of the No. 2 timing belt cover in the sequence shown.
(j) Remove the 4 nuts, grommets, cylinder head cover and
gasket.
HINT:
Arrange the grommets in the correct order, so that they can be
reinstalled into their original positions. This minimizes any pos-
sibility of oil leakage due to reuse of the grommets in different
positions.

P25455
Turn
P03443
1
1
2
2
1
13
3
P03442
2 233 44
44
P13927
Upward
Cam Lobe
Spark Plug SideNotch EM−6
− ENGINE MECHANICALVALVE CLEARANCE
1996 RAV4 (RM447U)
3. SET NO. 1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley and align its groove with timing
mark ”0” of the No. 1 timing belt cover.
(b) Check that the valve lifters on the No.1 cylinder are loose
and valve lifters on the No.4 are tight.
If not, turn the crankshaft 1 revolution (360°) and align the mark
as above.
4. INSPECT VALVE CLEARANCE
(a) Check only the valves indicated.
Using a feeler gauge, measure the clearance be-
tween the valve lifter and camshaft.
Record the out−of−specification valve clearance
measurements. They will be used later to determine
the required replacement adjusting shim.
Valve clearance (Cold):
Intake0.19 − 0.29 mm (0.007 − 0.011 in.)
Exhaust0.28 − 0.38 mm (0.011 − 0.015 in.)
(b) Turn the crankshaft 1 revolution (360°) and align the mark
as above (See procedure in step 3).
(c) Check only the valves indicated as shown. Measure the
valve clearance (See procedure in step (a)).
5. ADJUST VALVE CLEARANCE
(a) Remove the adjusting shim.
Turn the crankshaft so that the cam lobe of the cam-
shaft on the adjusting valve points upward.
Position the notch of the valve lifter facing the spark
plug side.

P03518
: Seal Packing
P01655
Marking
30°
Z17351
2 1 EM−10
− ENGINE MECHANICALVALVE CLEARANCE
1996 RAV4 (RM447U)
6. REINSTALL CYLINDER HEAD COVER
(a) Remove any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826−00080 or equivalent
(c) Install the gasket to the cylinder head cover.
(d) Install the head cover with the 4 grommets and nuts. Uni-
formly tighten the nuts in several passes.
Torque: 23 N·m (230 kgf·cm, 17 ft·lbf)
HINT:
Install the grommets so that their markings are as shown in the
illustration.
(e) Install the engine wire protector to the 2 mounting bolts of
the No. 2 timing belt cover in the sequence shown.
(f) Connect the high−tension cords to the spark plugs.
(g) Install the accelerator cable bracket with the 2 bolts.
(h) Connect the accelerator cable to the throttle body.
(i) Connect the accelerator cable to the clamp on the intake
manifold.
(j) Connect the accelerator cable to the clamp on the gener-
ator bracket.
(k) Connect the A/T throttle control cable to the throttle body.
(l) Connect the PCV hose to the air cleaner hose.
(m) Connect the PCV hose to the intake manifold.
7. CONNECT PS RESERVOIR

EM0EL−02
− ENGINE MECHANICALTIMING BELT
EM−13
1996 RAV4 (RM447U)
TIMING BELT
COMPONENTS

EM−14
− ENGINE MECHANICALTIMING BELT
1996 RAV4 (RM447U)

EM0EM−03
S01283
B
SST
A
S01358
Oil Pump
S01630
SST
SST
− ENGINE MECHANICALTIMING BELT
EM−15
1996 RAV4 (RM447U)
REMOVAL
1. DISCONNECT PS RESERVOIR AND REMOVE RES-
ERVOIR BRACKET
2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1
3. REMOVE GENERATOR (See page CH−7)
4. REMOVE GENERATOR BRACKET
5. w/ ABS:
REMOVE NO. 3 ABS ACTUATOR BRACKET (See page
BR−40)
6. REMOVE RH FRONT WHEEL
7. REMOVE RH ENGINE UNDER COVER
8. REMOVE PS PUMP DRIVE BELT
(a) Loosen the bolt A.
(b) Using SST and a deep socket wrench, loosen the bolt B.
SST SST09249−63010
(c) Remove the drive belt.
9. SLIGHTLY JACK UP ENGINE
Attach the jack to the oil pan, and raise the engine enough to
remove the weight from the engine mounting on the right side.
10. REMOVE RH ENGINE MOUNTING INSULATOR
11. REMOVE SPARK PLUGS
12. REMOVE CRANKSHAFT PULLEY
(a) Using SST (and bolt), remove the pulley bolt.
SST 09213−54015 (91651−60855 for type A),
09330−00021
Bolt: Part No. 91121−40665 for type B
HINT:
Either of 2 types of pulley may be used, each with its own
bolt size, type A and type B.
When using bolt type B, a plate washer must be inserted
between the bolt and SST.

S01655
SST
S01284
SST
S01624
S01597
S01651
EM−16
− ENGINE MECHANICALTIMING BELT
1996 RAV4 (RM447U)
(b) Using SST, remove the pulley.
SST 09950−50010 (09951−05010, 09952−05010,
09953−05010, 09953−05020,
09954−05020 for type A,
09954−05010 for type B)
13. REMOVE RH ENGINE MOUNTING BRACKET
Using SST, remove the 3 bolts and mounting bracket.
SST 09249−63010
14. REMOVE NO. 2 TIMING BELT COVER
(a) Disconnect the engine wire from the timing belt cover.
(b) Remove the 4 bolts and timing belt cover.
15. TEMPORARILY INSTALL CRANKSHAFT PULLEY
(a) Align the pulley set key with the key groove of the pulley,
and slide on the pulley.
(b) Temporarily install the pulley bolt.
16. SET NO. 1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley and align its groove with timing
mark ”0” of the No. 1 timing belt cover.
(b) Check that the hole of the camshaft timing pulley is
aligned with the timing mark of the bearing cap.
If not, turn the crankshaft 1 revolution (360°).
17. REMOVE TIMING BELT FROM CAMSHAFT TIMING
PULLEY
HINT:
When re−using timing belt:
Place matchmarks on the timing belt and camshaft timing
pulley, and place matchmark on timing belt to match the end of
the No. 1 timing belt cover.