1996 TOYOTA LAND CRUISER Drive

BO48R−01
BO−84
−
BODY FRONT SEAT (Power Adjuster Type)
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE FRONT SEAT HEADREST
2. REMOVE SIDE SUPPORT ADJUSTER KNOB
Using a screwdriver, remove the snap ring and side support ad-
juster knob.
3. REMOVE SEATBACK BOARD
(a) Remove the 2 screws.
(b) Slide the board downward to remove it.
4. REMOVE FRONT SEATBACK ASSEMBLY
(a) Using a hog ring pliers, remove the hog ring backward of seatback.
(b) Remove the 4 bolts and front seatback assembly. Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
5. REMOVE FRONT SEAT CUSHION INNER SHIELD
6. REMOVE FRONT SEAT INNER BELT
7. REMOVE FRONT SEAT CUSHION SHIELD
8. REMOVE FRONT SEAT CUSHION
(a) Remove the 4 bolts.
Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
(b) Disconnect the connector, then remove the front seat cushion.
9. REMOVE SEAT CUSHION REAR PROTECTOR
10. REMOVE RECLINING ADJUSTER INSIDE COVER
Remove the 4 screws and reclining adjuster inside cover LH
and RH.
11. REMOVE POWER ADJUST FRONT SHIELD
Remove the 2 screws and front shield.
12. REMOVE SLIDE MOTOR
(a) Using the 5.0 mm (0.20 in.) hexagon wrench, remove the
4 housing bracket screws.
Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)
(b) Hold the front seat horizontal jack screw with a plier, and remove the 2 nuts and 2 washers.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
HINT:
At the time of installation, apply adhesive to nut. Part No. 08833 − 00070, THREE BOND 1324 or equiva-
lent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO0632
BO39M−01
BO0633
15°
45°
N10070
Full Belt Length
minus 200 mm
(7.87 in.)
−
BODY SEAT BELT
BO−93
1996 LAND CRUISER (RM451U)
SEAT BELT
INSPECTION
CAUTION:
Replace the seat belt assembly (outer belt, inner belt, bolts,
nuts or sill −bar) if it has been used in a severe impact. The
entire assembly should be replaced even if damage is not
obvious.
1. All seat belts: RUNNING TEST (IN SAFE AREA)
(a) Fasten the front seat belts.
(b) Drive the car at 10 mph (16 km/h) and make a very hard stop.
Check that the belt locks and cannot be extended at this
time.
HINT:
Conduct this test in a safe area. If the belt does not lock, remove
the belt mechanism assembly and conduct the following static
check. Also, whenever installing a new belt assembly, verify the
proper operation before installation.
2. Driver ’s seat belt (ELR): STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
(c) Tilt the retractor slowly.
(d) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out at over 45 degrees
of tilt.
If a problem is found, replace the assembly.
3. Except driver’s seat belt (ALR/ELR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
(c) Pull out the whole belt and measure the length of the whole belt.
Then retract the belt slightly and pull it out again.
(d) Make sure that the belt cannot be extended further.
If a problem is found, replace the assembly.
(e) Retract the whole belt, then pull it out to the full length mi-
nus 200 mm (7.87 in.).
(f) Tilt the retractor slowly.
(g) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out at over 45 degrees
of tilt.
If a problem is found, replace the assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1CJ-01
R12236
A
-
BRAKE BRAKE MASTER CYLINDER
BR-1 1
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE RESERVOIR
(a) Remove the set screw and pull out the reservoir.
Torque: 1.7 N´m (17.5 kgf´cm, 15.2 in.´lbf)
(b) Remove the cap and strainer from the reservoir.
2. REMOVE 2 GROMMETS
3. REMOVE BOLT AND CLAMP FROM CYLINDER BODY
4. PLACE CYLINDER IN VISE
5. REMOVE PISTON STOPPER BOLT
Using a screwdriver, push the pistons in all the way and remove
the piston stopper bolt and gasket.
HINT:
Tape the screwdriver tip before use. Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
6. REMOVE 2 PISTONS AND SPRINGS
(a) Push in the piston with a screwdriver and remove the snap ring with snap ring pliers.
HINT:
Tape the screwdriver tip before use.
(b) Remove the No.1 piston and spring by hand, pulling straight out, not at an angle.
NOTICE:
If pulled out and installed at an angle, there is a possibly
that the cylinder bore could be damaged.
NOTICE:
Be careful not to damage the rubber lips on the pistons.
(c) Place a rag and 2 wooden blocks on the work table, and lightly tap the cylinder flange against the block edges until
the No.2 piston drops out of the cylinder.
HINT:
Make sure that the distance (A) from the rag to the top of the
blocks is at least 100 mm (3.94 in.).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1CV−04
BR2008
Z09007
170 mm
(6.70 in.)50 mm
(1.97
in.)
16 mm
(0.63 in.)
BR0213
BR2009
BR−26
−
BRAKE FRONT BRAKE CALIPER
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE CYLINDER BOOT SET RINGS AND BOOTS
Using a screwdriver, remove the 4 cylinder boot set rings and
boots.
2. REMOVE PISTONS FROM CYLINDER
(a) Prepare the wooden plate to hold the pistons.
(b) Place the plate between the pistons and insert a pad at
one side.
(c) Use compressed air to remove the pistons alternately from the cylinder.
CAUTION:
Do not place your fingers in front of the pistons when using
compressed air.
3. REMOVE PISTON SEALS
Using a screwdriver, remove the 4 piston seals from the cylin-
der.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D3−01
−
BRAKE REAR BRAKE CALIPER
BR−35
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE CYLINDER BOOT
Using a screwdriver, remove the cylinder boot from the caliper.
2. REMOVE PISTON
(a) Place a piece of cloth or similar article between the piston
and the caliper.
(b) Use compressed air to remove the piston from the cylin- der.
CAUTION:
Do not place your fingers in front of the piston when using
compressed air.
3. REMOVE PISTON SEAL
Using a screwdriver, remove the piston seal from the cylinder.
4. REMOVE DUST BOOT AND SLIDING BUSHING
Using a screwdriver and hammer, tap out dust boot and sliding
bushing.
HINT:
Tape the screwdriver tip before use.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BRAKE PARKING BRAKE
BR−41
1996 LAND CRUISER (RM451U)
7. REMOVE REAR SHOE, ADJUSTER AND TENSION
SPRING
(a) Slide out the rear shoe, and remove the rear shoe and ad-
juster.
(b) Remove the 2 shoe hold −down spring cups, spring and
pin.
(c) Remove the lower side tension spring.
8. REMOVE FRONT SHOE
(a) Slide out the front shoe.
(b) Remove the shoe 2 hold −down spring cups, springs and
pin.
(c) Disconnect the parking brake cable from the parking
brake shoe lever.
9. IF NECESSARY, REMOVE AND DISASSEMBLE PARKING BRAKE BELLCRANK ASSEMBLY
(a) Using a screwdriver, remove the C −washer.
(b) Remove the pin and disconnect the parking brake cable No.2 from the bellcrank.
(c) Remove the clip.
(d) Remove the pin and clip, then disconnect the parking
brake cable.
(e) Remove the 2 tension springs.
(f) Remove the 2 bolts and parking brake bellcrank assem- bly.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(g) Remove the boot from parking brake bellcrank bracket.
(h) Using a screwdriver, remove the C −washer and pin.
(i) Remove the parking brake bellcrank from the bell crank bracket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BRAKE PARKING BRAKE
BR−43
1996 LAND CRUISER (RM451U)
6. IF NECESSARY, REPLACE SHIM
(a) Using a screwdriver, remove the C −washer.
(b) Remove the park ing brake shoe lever, and install the cor-
rect size shim.
(c) Using needle −nose pliers, install the parking brake shoe
lever with a new C −washer.
(d) Remeasure the clearance.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1DA−01
BR−44
−
BRAKE PARKING BRAKE
1996 LAND CRUISER (RM451U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See
page BR−40 ).
NOTICE:
Apply high temperature grease and lithium soap base gly-
col grease to the parts indicated by the arrows (See page
BR−39 ).
1. ADJUST PARKING BRAKE SHOE CLEARANCE
(a) Disconnect the PKB cable from bellcrank and remove the 2 tension springs.
(b) Loosen the stopper bolt.
(c) Temporarily install the hub nuts.
(d) Remove the hole plug.
(e) Turn the adjuster and expand the shoes until the disc
locks.
(f) Return the adjuster 8 notches.
(g) Install the hole plug.
2. ADJUST BELLCRANK
(a) Pull the bellcrank until all play in the interior linkage is tak-
en up.
(b) Screw in the bellcrank adjusting bolt to where it contacts on the dust seal.
(c) Loosen it one turn, and lock it at that position with the lock nut.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(d) Install the bellcrank spring.
(e) Connect the PKB cable to the bellcrank.
3. BEDDING DOWN PARKING BRAKE SHOES AND
DISC
(a) Drive the vehicle at about 50 km/h (31 mph) on a safe, lev-
el and dry road.
(b) With the parking brake release button pushed in, pull on the lever with 88 N (9 kgf, 19.8 lbf) of force.
(c) Drive the vehicle for about 400 meters (0.25 mile) in this condition.
(d) Repeat this procedure 2 or 3 times.
4. RECHECK AND ADJUST PARKING BRAKE LEVER TRAVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010