1996 TOYOTA LAND CRUISER Drive

BO37O−01
−
BODY FRONT DOOR
BO−11
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE GLASS CHANNEL WITH SCREWDRIVER
OR LIKE OBJECT
2. A P P LY S O A P Y WAT E R TO I N S I D E O F W E AT H- ERSTRIP
3. INSTALL CHANNEL BY TAPPING IT WITH PLASTIC HAMMER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37S−01
−
BODY REAR DOOR
BO−15
1996 LAND CRUISER (RM451U)
DISASSEMBLY
HINT:
Tape a screwdriver tip before using to pry parts.
1. REMOVE DOOR INSIDE HANDLE BEZEL
2. REMOVE DOOR SPEAKER COVER
3. REMOVE ASH TRAY
4. REMOVE ARMREST BASE UPPER
5. REMOVE ARMREST
6. REMOVE DOOR TRIM
(a) Remove the courtesy light.
(b) Remove the 3 screws from the door trim.
(c) Using a screwdriver, remove the clips and remove the trim
by pulling all of the trim up.
(d) Remove the inner weatherstrip from the door trim.
(e) Remove the 11 screws and the armrest base from the door trim.
7. REMOVE DOOR BELT MOULDING
Pry out the clip from the edge of the panel, and remove the
moulding.
8. REMOVE DOOR WEATHERSTRIP
NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
9. REMOVE DOOR INSIDE HANDLE
10. REMOVE SERVICE HOLE COVER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37T−01
−
BODY REAR DOOR
BO−17
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE GLASS CHANNEL WITH SCREWDRIVER
OR LIKE OBJECT
2. A P P LY S O A P Y WAT E R TO I N S I D E O F W E AT H- ERSTRIP
3. INSTALL CHANNEL BY TAPPING IT WITH PLASTIC HAMMER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37W−01
−
BODY BACK DOOR
BO−21
1996 LAND CRUISER (RM451U)
DISASSEMBLY
HINT:
Tape the screwdriver tip before using to pry parts.
1. REMOVE UPPER BACK DOOR
(a) Remove the pull handle and pull handle bezel.
(b) Remove the back door trim.
(1) Insert a screwdriver, between the retainers and trim
to pry it loose.
(2) Remove the back door trim.
(c) Remove the door weatherstrip.
NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
(d) Remove the weatherstrip upper.
NOTICE:
Do not pull strongly off the weatherstrip as it may tear.
(e) Remove the door inside handle.
(f) Remove the door lock control.
(g) Remove the outside handle.
(h) Remove the door lock cylinder.
(i) Remove the wiper arm.
(j) Remove the wiper motor.
(k) Remove the wiper control relay.
(l) Remove the door lock.
(m) Remove the damper stay.
2. REMOVE LOWER BACK DOOR
(a) Remove the door trim. (1) Insert a screwdriver, between the retainers and
door trim to pry it loose.
(2) Remove the door trim.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO385−01
−
BODY REAR WIPER AND WASHER
BO−31
1265
Author: Date:
1996 LAND CRUISER (RM451U)
REAR WIPER AND WASHER
REMOVAL
1. REMOVE PULL HANDLE AND PULL HANDLE BEZEL
2. REMOVE BACK DOOR TRIM
(a) Insert a screwdriver between the retainers and door trim
to pry it loose.
HINT:
Tape the screwdriver tip before use.
(b) Remove the back door trim.
3. REMOVE WIPER ARM, MOTOR AND REAR WIPER CONTROL RELAY
(a) Open the cap.
(b) Remove the nut and wiper arm.
(c) Remove the 5 bolts and motor, then disconnect the con- nector.
(d) Remove the bolts and rear wiper control relay,then dis- connect the connector.
4. ADJUST REAR WASHER NOZZLE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14076
N14077
N14078
N14079
N14440
−
BODY WHEEL OPENING MOULDING
BO−39
1996 LAND CRUISER (RM451U)
(b) Remove the quarter trim RH.
(c) Remove the quarter trim LH.
4. REMOVE QUARTER OUTSIDE MOULDING
(a) Remove the 2 nuts.
(b) Remove the screw.
(c) Using a screwdriver, pry out the rearwheel moulding.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO38T−01
−
BODY QUARTER WINDOW GLASS
BO−51
1996 LAND CRUISER (RM451U)
REMOVAL
1. w/ No. 2 rear seat:
NO. 2 REAR SEAT
2. REMOVE BACK DOOR SCUFF PLATE
3. REMOVE QUARTER TRIM
4. REMOVE REAR SEAT SIDE GARNISH
5. REMOVE REAR DOOR SCUFF PLATE
6. REMOVE QUARTER PILLAR GARNISH
7. REMOVE REAR PILLAR GARNISH
8. REMOVE ASSIST GRIPS
9. LOOSEN ROOF HEADLINING
10. REMOVE VENT LOUVER AND QUARTER BELT MOULDING
(a) Remove the nut from the vent louver.
(b) Insert a screwdriver between the retainers and body to pry it loose.
HINT:
Tape the screwdriver tip before use.
(c) Pull out the vent louver.
(d) Pull out the clips from the edge of the panel, and remove the moulding.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−52
−
BODY QUARTER WINDOW GLASS
1996 LAND CRUISER (RM451U)
11. If reusing the weatherstrip:
REMOVE QUARTER WINDOW GLASS
(a) Using a screwdriver loosen the weatherstrip from the
body.
NOTICE:
Be careful not to damage the body.
(b) Pry the lip of the weatherstrip outward from the interior part of the body flange.
(c) Pull the glass outwards and remove it with the weather- strip.
12. If using a new weatherstrip: REMOVE QUARTER WINDOW GLASS
(a) From outside of the vehicle, cut off the weatherstrip lip with a knife.
NOTICE:
Do not damage the body and the glass.
(b) Push the glass outwards and remove the glass.
(c) Remove the remaining weatherstrip.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010