1996 TOYOTA LAND CRUISER fuel pressure

P09286
New O−ring
Grommet Injector
Delivery Pipe WRONG
CORRECT
P09401
Fuel Return Hose
SF−4
−
SFI SFI SYSTEM
632
Author: Date:
1996 LAND CRUISER (RM451U)
(d) Observe the following precautions when removing and
installing the injectors.
(1) Never reuse the O −ring.
(2) When placing a new O −ring on the injector, take
care not to damage it in any way.
(3) Coat a new O −ring with spindle oil or gasoline be-
fore installing −never use engine, gear or brake oil.
(e) Install the injector to the delivery pipe and intake manifold
as shown in the illustration.
(f) Check that there are no fuel leaks after doing mainte- nance anywhere on the fuel system.
(1) Remove the fuse cover on the instrument panel.
(2) Connect the TOYOTA hand− held tester to the
DLC3.
(3) Turn the ignition switch ON and TOYOTA hand −
held tester main switch ON.
NOTICE:
Do not start the engine. (4) Select the active test mode on the TOYOTA hand−held tester.
(5) Please refer to the TOYOTA hand −held tester oper-
ator ’s manual for further details.
If you have no T OYOTA hand−held tester, connect the positive
(+) and negative ( −) leads from the battery to the fuel pump con-
nector (See page SF−14 ).
(6) Pinch the fuel return hose. The pressure in the high
pressure line will rise to approx. 392 kPa (4 kgf/cm
2,
57 psi). In this state, check to see that there are no
leaks from any part of the fuel system.
NOTICE:
Always pinch the hose. Avoid bending as it may cause the
hose to crack.
(7) Turn the ignition switch to LOCK.
(8) Disconnect the TOYOTA hand −held tester from the
DLC3.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EM−01
−
SFI FUEL PRESSURE REGULATOR
SF−19
647
Author: Date:
1996 LAND CRUISER (RM451U)
FUEL PRESSURE REGULATOR
ON−VEHICLE INSPECTION
INSPECT FUEL PRESSURE (See page SF−1 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0XZ−04
SF−20
−
SFI FUEL PRESSURE REGULATOR
1996 LAND CRUISER (RM451U)
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Y0−06
−
SFI FUEL PRESSURE REGULATOR
SF−21
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT VACUUM SENSING HOSE FROM FUEL
PRESSURE REGULATOR
2. DISCONNECT FUEL RETURN HOSE FROM FUEL PRESSURE REGULATOR
CAUTION:
Put a shop towel under the pressure regulator.
3. REMOVE FUEL PRESSURE REGULATOR
(a) Loosen the lock nut, and remove the pressure regulator.
(b) Remove the O−ring from the pressure regulator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Y1−06
SF−22
−
SFI FUEL PRESSURE REGULATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL FUEL PRESSURE REGULATOR
(a) Fully loosen the lock nut on the pressure regulator.
(b) Apply a light coat of gasoline to a new O −ring, and install
it to the pressure regulator.
(c) Insert the pressure regulator into the delivery pipe by hand completely.
(d) Turn the pressure regulator counterclockwise until the fuel outlet port faces in the direction indicated in the il-
lustration.
(e) Tighten the lock nut. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
2. CONNECT FUEL RETURN HOSE TO FUEL PRES-
SURE REGULATOR
3. CONNECT V ACUUM SENSING HOSE TO FUEL PRES-
SURE REGULATOR
4. START ENGINE AND CHECK FOR FUEL LEAKAGE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Y1−06
SF−22
−
SFI FUEL PRESSURE REGULATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL FUEL PRESSURE REGULATOR
(a) Fully loosen the lock nut on the pressure regulator.
(b) Apply a light coat of gasoline to a new O −ring, and install
it to the pressure regulator.
(c) Insert the pressure regulator into the delivery pipe by hand completely.
(d) Turn the pressure regulator counterclockwise until the fuel outlet port faces in the direction indicated in the il-
lustration.
(e) Tighten the lock nut. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
2. CONNECT FUEL RETURN HOSE TO FUEL PRES-
SURE REGULATOR
3. CONNECT V ACUUM SENSING HOSE TO FUEL PRES-
SURE REGULATOR
4. START ENGINE AND CHECK FOR FUEL LEAKAGE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
SFI INJECTOR
SF−27
1996 LAND CRUISER (RM451U)
18. DISCONNECT PS RESERVOIR TANK
Remove the 3 bolts and disconnect the reservoir tank.
19. REMOVE ENGINE OIL DIPSTICK
20. DISCONNECT GROUND STRAP
21. REMOVE INTAKE MANIFOLD STAY
Remove the 2 bolts and intake manifold stay.
22. DISCONNECT VACUUM HOSES FROM TVV
23. DISCONNECT NO.1 WATER BYPASS HOSE FROM
CYLINDER HEAD
24. REMOVE AIR INTAKE CHAMBER
Remove the 6 bolts, 2 nuts, air intake chamber and 2 gaskets.
25. REMOVE FUEL RETURN PIPE
(a) Disconnect the fuel hose from the fuel pressure regulator.
(b) Remove the 2 bolts and fuel return pipe.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EO−03
−
SFI INJECTOR
SF−29
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT INJECTOR INJECTION
CAUTION:
Keep injector clean of sparks during the test.
(a) Connect SST (union and hose) to the fuel filter outlet with
the 2 gaskets and union bolt.
SST 09268−41046 (90405 −09015)
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
(b) Remove the fuel pressure regulator (See page SF−21).
(c) Install the O−ring to the fuel inlet of pressure regulator.
(d) Connect SST (hose) to the fuel inlet of the pressure regu-
lator with SST (union).
SST 09268−41046 (09268 −41091)
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(e) Connect the fuel return hose to the fuel outlet of the pres-
sure regulator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010