1996 TOYOTA LAND CRUISER Ect

P22234
From
Air
CleanerSignals ECM IAC ValveValve ShaftRotor
To Cylinders
Throttle Valve
Intake Air
Chamber
Coils
Valve
−
DIAGNOSTICS ENGINE
DI−89
1996 LAND CRUISER (RM451U)
DTC P0505 Idle Control System Malfunction
CIRCUIT DESCRIPTION
The step motor type IAC valve is located in front of the intake
air chamber. Intake air bypassing the throttle valve is directed
to the IAC valve through a passage. A step motor is built into
the IAC valve. It consists of four coils, a magnetic rotor, valve
shaft and valve. When current flows to the coils due to signals
from the ECM, the rotor turns and moves the valve shaft forward
or backward, changing the clearance between the valve and
the valve seat. In this way the intake air volume bypassing the
throttle valve is regulated, controlling the engine speed. There
are 125 possible positions to which the valve can be opened.
DTC No.DTC Detecting ConditionTrouble Area
P0505Idle speed continues to vary greatly from the target speed
(2 trip detection logic)
 IAC valve is stuck or closed
 Open or short in IAC valve circuit
 Open or short in A /C signal circuit
 Air intake (hose loose)
DI5PO−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22474
EBBR
22 22
1 3
4
2 2
2
R−Y R/B No.2
From BatteryR
Y−R
EA2
EB1
Y−RY −R
Y−R R
R−G
R−B
G−Y
Y−L
4
1
3 6
IAC Valve MRLY
E7
E4
E4
E4
E4 7 3
6
5
4
ISC1
ISC2
ISC3
ISC4 B+
E01
E01
E01
E01
EFI
2
5
EFI Main
Relay
7
1 ECM
A00202
ISC1
ISC2
ISC3
ISC4 A/C Switch OFF
→ ON
(IAC Valve Open)
20 V/Division
10 msec./Division
ISC1
ISC2
ISC3
ISC4 20 V/
Division
10 msec./Division
(IAC Valve Close)
A/C Switch ON →
OFF
FI6536
FI6537
DI−90
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Reference: INSPECTION USING OSCILLOSCOPE
With the engine idling measure wavefoms between terminals
ISC1, ISC2, ISC3, ISC4 and E01 of ECM when A/C switch ON
or OFF.
HINT:
The correct waveforms are as shown.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00178
ONISC1 ISC3ISC2 ISC4
E4 connector
(−) (+)
BE6653
P24669
−
DIAGNOSTICS ENGINE
DI−91
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check air induction system (See page SF−1 ).
NG Repair or replace.
OK
2 Check voltage terminals ISC1, ISC2, ISC3, ISC4, of ECM connector and bod\
y ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Disconnect the E4 connector of ECM.
(c) Turn ignition switch ON.
CHECK:
Measure voltage between terminals ISC1, ISC2, ISC3, ISC4 of
ECM connector and body ground.
OK:
Voltage: 9 − 14 V
OK Go to step 4.
NG
3 Check IAC valve (See page SF−49 ).
NG Replace IAC valve.
OK
Check for open and short in harness and co −nnector between EFI main relay (Marking:EFI) and
IAC valve and ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00203
CloseOpen Battery
Battery
B1
S1
S2 B2S4
S3
B1
S1 S2 B2S4S3
P24670
P24671
DI−92
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check operation of the IAC valve .
PREPARATION:
Remove IAC valve (See page SF−51).
CHECK:
(a) Connect the positive (+) leak from the battery to terminals
5 (B1) and 2 (B2), and the negative ( −) lead to terminals
4 (S1), −1 (S2), −6 (S3), −3 (S4) in that order.
(b) Connect the positive (+) lead from the battery to terminals
5 (B1) and 2 (B2), and the negative ( −) lead to terminals
3 (S4), − 6 (S3), −1 (S2), − 4 (S1) in that order.
OK:
(1) The valve moves to close direction.
(2) The valve moves to open direction.
HINT:
The ACTIVE TEST mode of the T OYOTA hand−held tester can
be used to change the step of the IAC valve as desired.
NG Repair or replace IAC valve.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−93
1996 LAND CRUISER (RM451U)
DTC P0510 Closed Throttle Position Switch Malfunction
CIRCUIT DESCRIPTION
Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit \
Malfunction) on page DI−35.
DTC No.DTC Detecting ConditionTrouble Area
P0510
The closed throttle position switch does not turn ON or OFF
even once when the vehicle is driven
(2 trip detection logic)Open or short in closed throttle position switch circuit
 Closed throttle position switch
 ECM
HINT:
After confirming DTC P0510 use the TOYOTA hand−held tester to confirm the closed throttle position switch
signal from ”CURRENT DATA”.
Throttle ValveClosed Throttle Position Switch SignalMalfunction
Fully closedOFFOpen circuit
Fully openONShort circuit
WIRING DIAGRAM
Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) on page DI−35 for WIR-
ING DIAGRAM.
INSPECTION PROCEDURE
HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read CTP switch signal.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
RESULT:
Throttle ValveClosed Throttle Position Switch SignalMalfunction
Fully closedOFFOpen circuit: Go to step 2
Fully openONShort circuit: Go to step 4
DI5PP−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6653
FI7058A00486
Throttle Position
SensorON
4
3
21
1
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC
IDL
E2 E112V
5V
FI7064
A00487
Throttle Position Sensor
4
3
2
11
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC
IDL
E2 E112V
5V
IDL E2
ON
DI−94
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect throttle position sensor connector.
(b) Connect sensor wire harness terminals between terminals 1 and 2.
(c) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: ON
OK Confirm good connection at sensor. If OK, replace throttle position sensor.
NG
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Connect between terminals IDL and E2 of ECM.
HINT:
Throttle position sensor connector is disconnected.
Before checking, do a visual check and contact pressure check
for connector (See page IN−28).
(c) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: ON
OK Open in harness between ECM and throttle position sensor, repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6653A00499A00488
Throttle Position Sensor
4
3
2
11
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC IDL1
E2 E112V
5V
ON
BE6653
A00496 A00498
A00489
4
3
2
11
11
9
10
E5
E5
E5 E5
VTA1
ECM
VCC IDL1
E2 12V
5V
ON
Throttle Position
Sensor
E5 Connector
−
DIAGNOSTICS ENGINE
DI−95
1996 LAND CRUISER (RM451U)
4 Check for short in harness or ECM.
PREPARATION:
(a) Disconnect throttle position sensor connector.
(b) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: OFF
OK Confirm good connection at sensor. If OK, replace throttle position sensor.
NG
5 Check for short in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Disconnect E5 connector of ECM.
HINT:
Throttle position sensor connector is disconnected.
(c) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: OFF
OK Short in harness between ECM and throttle position sensor, repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00492
43
2
11
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC
IDL
E2E1 12V
5V
ON
Throttle Position Sensor
DI−96
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
OBD II scan tool (excluding TOYOTA hand −held tester)
1 Check for open and short in harness or ECM.
PREPARATION:
(a) Disconnect throttle position sensor connector.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals 1 and 2 of throttle position
sensor connector.
OK:
Voltage: 9 − 14 V
OK Confirm good connection at sensor. If OK, replace throttle position sensor.
NG
2 Check for open and short in harness and connector between throttle posit\
ion sensor and ECM (See page IN−28).
NG Open or short in harness between ECM and
throttle position sensor.
OK
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010