1996 TOYOTA LAND CRUISER Hoses

EM−74
−
ENGINE MECHANICAL ENGINE UNIT
1996 LAND CRUISER (RM451U)
29. REMOVE FRAME CROSSMEMBER
(a) Remove the 2 nuts holding the crossmember to the en-
gine rear mounting insulator.
(b) Remove the 8 bolts and crossmember.
30. REMOVE ENGINE WITH TRANSMISSION
(a) Attach the engine hoist chain to the 2 engine hangers.
(b) Remove the 2 nuts holding the engine front mounting in- sulators to the frame.
(c) Lift the engine with transmission out of the vehicle slowly
and carefully.
NOTICE:
Make sure that the engine is clear of all wiring and hoses.
(d) Place the engine and transmission assembly onto the stand.
31. REMOVE OIL DIPSTICK GUIDE FOR TRANSMISSION
(a) Disconnect the 2 breather hoses.
(b) Remove the 2 mounting bolts.
(c) Pull out the dipstick guide and dipstick from the transmis- sion.
(d) Remove the O−ring from the dipstick guide.
32. DISCONNECT ENGINE WIRE FROM TRANSMISSION
(a) Disconnect the PNP switch connector.
(b) Disconnect the 2 connectors from the transmission.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL ENGINE UNIT
EM−77
1996 LAND CRUISER (RM451U)
9. INSTALL OIL DIPSTICK GUIDE FOR TRANSMISSION
(a) Install a new O−ring to the dipstick guide.
(b) Apply a light coat of ATF to the O −ring.
(c) Connect the dipstick guide end to the tube of the oil pan, and install the dipstick guide with the 2 bolts.
(d) Install the dipstick.
(e) Connect the 2 breather hoses.
10. INSTALL ENGINE AND TRANSMISSION ASSEMBLY IN VEHICLE
(a) Attach the engine hoist chain to the engine hangers.
(b) Lower the engine and transmission assembly into the en-
gine compartment.
(c) Insert the stud bolts of the front engine mounting insula- tors into the stud bolt holes of the frame.
(d) Temporarily install the 2 nuts holding the engine front mounting insulators to the frame crossmember.
(e) Keep the engine level with a jack.
(f) Remove the hoist chain.
11. INSTALL FRAME CROSSMEMBER
(a) Temporarily install the crossmember to the engine rear mounting insulator with the 2 nuts.
(b) Install the 8 bolts holding the crossmember to the frame. Torque: 61 N·m (620 kgf·cm, 45 ft·lbf)
(c) Tighten the 2 nuts holding the crossmember to the engine
rear mounting insulator.
Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
12. TIGHTEN NUTS HOLDING ENGINE FRONT MOUNT- ING INSULATORS TO FRAME
Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
13. CONNECT GROUND STRAP TO HEAT INSULATOR
14. INSTALL FRONT EXHAUST PIPE
(a) Install 2 new gaskets and the front exhaust pipe with the
4 nuts.
Torque: 63 N·m (630 kgf·cm, 46 ft·lbf)
(b) Install the No.1 support bracket with the 2 bolts.
Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(c) Connect the clamp and tighten the clamp bolt. Torque: 19.5 N·m (195 kgf·cm, 14 ft·lbf)
(d) Connect the front exhaust pipe to the rear TWC with a
new gasket, 2 bolts and 2 nuts.
Torque: 46 N·m (470 kgf·cm, 34 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−80
−
ENGINE MECHANICAL ENGINE UNIT
1996 LAND CRUISER (RM451U)
19. CONNECT ENGINE WIRE TO CABIN
(a) Push in the engine wire through the cowl panel.
(b) Connect the connectors.
(1) Connect the 3 connectors to the ECM.
(2) Connect the 2 connectors to the cowl wire.
(c) Connect the A/C amplifier with the screw.
(d) Install the speaker panel with the screw.
(e) Install the glove compartment door with the 2 screws.
20. CONNECT PS RETURN HOSE
Connect the return hose to the PS reservoir tank.
21. CONNECT PS PRESSURE HOSE
Connect the PS pressure hose with 2 new gaskets and the
union bolt. Torque: 56 N·m (575 kgf·cm, 42 ft·lbf)
22. INSTALL RADIATOR PIPE
(a) Connect the No. 2 radiator hose to the water inlet.
(b) Install the 2 nuts holding the radiator pipe to the No. 1 oil pan.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
23. INSTALL A/C COMPRESSOR AND BRACKET
(a) Install the A/C compressor bracket with the 5 bolts.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the A/C compressor with the 4 bolts. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Install and adjust the drive belt (See page CH−2).
24. CONNECT WIRES AND CONNECTORS
(a) Connect the 2 heated oxygen sensor connectors.
(b) Connect the DLC1 clamp.
(c) Connect the 2 oil pressure gauge connectors.
(d) Connect the generator wire and connector.
(e) Connect the connector on the intake manifold to the fend-
er apron.
(f) Connect the high −tension cord to the ignition coil.
(g) Connect the ground strap to the No. 1 engine hanger.
(h) Connect the ground strap to the air intake chamber.
(i) Connect the starter wire.
(j) Connect the ground cable to the cylinder block.
25. CONNECT FUEL HOSES
(a) Connect the fuel inlet hose to the fuel filter with 2 new gas-
kets and the union bolt.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
(b) Connect the fuel return hose.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL ENGINE UNIT
EM−81
1996 LAND CRUISER (RM451U)
26. CONNECT EVAP HOSE
27. CONNECT BRAKE BOOSTER VACUUM HOSE
28. CONNECT HEATER VALVE AND ENGINE WIRE TO
COWL PANEL
(a) Connect the heater valve with the 2 bolts.
(b) Connect the engine wire and ground strap with the 2 bolts.
29. CONNECT HEATER HOSES
30. CONNECT ACCELERATOR CABLE TO THROTTLE BODY
31. CONNECT CRUISE CONTROL ACTUATOR CABLE TO
THROTTLE BODY
32. INSTALL AIR CLEANER CASE
33. INSTALL AIR CLEANER HOSE AND CAP
34. CONNECT OIL COOLER HOSE TO OIL COOLER PIPE
35. INSTALL RADIATOR (See page CO−16)
36. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
37. INSTALL BATTERY TRAY AND BATTERY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery and hold−down clamp with the nuts.
(d) Connect the battery cables.
38. FILL WITH ENGINE OIL
39. FILL RADIATOR WITH ENGINE COOLANT
40. START ENGINE AND CHECK FOR LEAKS
41. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
42. CHECK IGNITION TIMING (See page EM−10)
43. INSTALL HOOD
44. PERFORM ROAD TEST
Check for abnormal noise, shock, slippage, correct shift points
and smooth operation.
45. RECHECK ENGINE COOLANT AND ENGINE OIL LEV-
ELS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA02R−04
MA−4
−
MAINTENANCE UNDER HOOD
44
Author: Date:
1996 LAND CRUISER (RM451U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTICE
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performe\
d.
Periodic maintenance service must be performed according to whichever interval in\
the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time inter\
val (months).
Maintenance service after the last period should be performed at the same interval \
as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and incre\
ase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL Check that the coolant level is between the FULL and LOW lines on the se\
e −through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leave\
s, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upp\
er and lower level lines on the case.
If level is low, add distilled water only.
6. BRAKE FLUID LEVELS
Check that the brake fluid level is near the upper level line on the see\
−through reservoir.
7. ENGINE DRIVE BELTS
Check drive belt for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temp\
erature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking and foot brake applied, shift the sel\
ector into all positions from the P to L, and then shift into the P.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re −insert the dipstick fully and check that
the fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 − 80°C (158 − 176° F)).
HINT:
Wait about 30 minutes before checking the fluid level after extended driving\
at high speeds in hot weather,
driving in heavy traffic or with a trailer.
11. EXHAUST SYSTEM
Visually inspect for cracks, holes or loose supports.
If any change in the sound of the exhaust or smell of the exhaust fumes is\
noticed, have the cause located
and corrected.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA0055
MA02T−03
MA−6
−
MAINTENANCE BRAKE
46
Author: Date:
1996 LAND CRUISER (RM451U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND HOSES
HINT:
Check in a well lighted area. Check the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before checking the front brake.
(a) Check all brake lines and hoses.
Check for damage.
Check for wear.
Check for deformation.
Check for cracks.
Check for corrosion.
Check for leaks.
Check for bends.
Check for twists.
(b) Check all clamps for tightness and connections for leak- age.
(c) Check that the hoses and lines are clear of sharp edges, moving parts and the exhaust system.
(d) Check that the lines installed in grommets pass through the center of the grommets.
2. INSPECT FRONT BRAKE P ADS AND DISCS (See page
BR−27 )
3. INSPECT REAR BRAKE PADS AND DISCS (See page
BR−36 )
4. INSPECT PARKING BRAKE LININGS AND DRUMS
(See page BR−42 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KJ−01
−
PREPARATION AIR CONDITIONING
PP−71
120
Author: Date:
1996 LAND CRUISER (RM451U)
AIR CONDITIONING
SST (Special Service Tools)
07110−58060Air Conditioner Service Tool Set
(07117−58060)Refrigerant Drain Service Valve
(07117−58070)T−Joint
(07117−58080)Quick Disconnect AdapterDischarge (Diam.: 16 mm)
(07117−58090)Quick Disconnect AdapterSuction (Diam.: 13 mm)
(07117−78050)Refrigerant Charging Gauge
(07117−88060)Refrigerant Charging HoseDischarge (Color: Red)
(07117−88070)Refrigerant Charging HoseSuction (Color: Blue)
(07117−88080)Refrigerant Charging HoseUtility (Color: Green)
07112−66040Magnetic Clutch Remover
07112−76060Magnetic Clutch Stopper
07114−84010Snap Ring Pliers
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
SFI INJECTOR
SF−27
1996 LAND CRUISER (RM451U)
18. DISCONNECT PS RESERVOIR TANK
Remove the 3 bolts and disconnect the reservoir tank.
19. REMOVE ENGINE OIL DIPSTICK
20. DISCONNECT GROUND STRAP
21. REMOVE INTAKE MANIFOLD STAY
Remove the 2 bolts and intake manifold stay.
22. DISCONNECT VACUUM HOSES FROM TVV
23. DISCONNECT NO.1 WATER BYPASS HOSE FROM
CYLINDER HEAD
24. REMOVE AIR INTAKE CHAMBER
Remove the 6 bolts, 2 nuts, air intake chamber and 2 gaskets.
25. REMOVE FUEL RETURN PIPE
(a) Disconnect the fuel hose from the fuel pressure regulator.
(b) Remove the 2 bolts and fuel return pipe.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010