1996 TOYOTA LAND CRUISER Hoses

−
SFI INJECTOR
SF−33
1996 LAND CRUISER (RM451U)
(k) Connect the 6 injector connectors as shown.
2. INSTALL FUEL INLET PIPE
Install the fuel inlet pipe with 4 new gaskets, the 2 union bolts
and bolt.
Torque:
Union bolt: 29 N·m (300 kgf·cm, 22 ft·lbf)
Bolt: 20 N·m (200 kgf·cm, 14 ft·lbf)
3. INSTALL FUEL RETURN PIPE
(a) Install the fuel return pipe with the 2 bolts. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(b) Connect the fuel hose to the fuel pressure regulator.
4. INSTALL AIR INTAKE CHAMBER
Install 2 new gaskets and the air intake chamber with the 6 bolts
and 2 nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
5. CONNECT NO.1 WATER BYPASS HOSE TO CYL- INDER HEAD
6. CONNECT VACUUM HOSES TO TVV
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO0919
Z00085
FU0041
SF0P0−06
−
SFI FUEL TANK AND LINE
SF−37
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT FUEL TANK AND LINE
(a) Check the fuel lines for cracks or leakage, and all connec-
tions for deformation.
(b) Check the fuel tank vapor vent system hoses and connec-
tions for looseness, sharp bends or damage.
(c) Check the fuel tank for deformation, cracks fuel leakage
or tank band looseness.
(d) Check the filler neck for damage or fuel leakage.
(e) Hose and tube connections are as shown in the illustra- tion.
If a problem is found, repair or replace the part as necessary.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EW−04
−
SFI THROTTLE BODY
SF−45
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT NO.2 PCV HOSE
3. DISCONNECT AIR CLEANER HOSE
4. DISCONNECT CONTROL CABLES FROM THROTTLE
BODY
5. DISCONNECT THROTTLE POSITION SENSOR CON-
NECTOR
6. DISCONNECT IDLE AIR CONTROL VALVE CONNEC- TOR
7. REMOVE THROTTLE BODY
(a) Disconnect the EVAP hose.
(b) Disconnect the 3 vacuum hoses.
(c) Disconnect the No.2 water bypass hose.
(d) Remove the 4 bolts, and disconnect the throttle body from
the air intake chamber.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
(e) Remove the throttle body gasket.
HINT:
At the time of installation, plaese refer to the following items.
install a new gasket on the air intake chamber.
(f) Disconnect the No.1 water bypass hose from the throttle
body, and remove the throttle body.
(g) Disconnect the No.2 water bypass hose from the throttle
body.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1F9−01
−
SFI VSV FOR FUEL PRESSURE CONTROL
SF−59
687
Author: Date:
1996 LAND CRUISER (RM451U)
VSV FOR FUEL PRESSURE
CONTROL
INSPECTION
1. REMOVE AIR INTAKE CHAMBER (See page EM−28 )
2. DISCONNECT VACUUM HOSES AND CONNECTOR
3. INSPECT VSV FOR OPEN CIRCUIT
Using an ohmmeter, check that there is continuity between the
terminals. Resistance: 37 − 44 Ω at 20° C (68°F)
If there is no continuity, replace the VSV.
4. INSPECT VSV FOR GROUND
Using an ohmmeter, check that there is no continuity between
each terminal and the body.
If there is continuity, replace the VSV.
5. INSPECT VSV OPERATION
(a) Check that the air flows from pipe E to pipe G.
(b) Apply battery voltage across the terminals.
(c) Check that the air does not flows from pipe E to the filter.
If operation is not as specified, replace the VSV.
6. RECONNECT VACUUM HOSES AND CONNECTOR
7. REINSTALL AIR INTAKE CHAMBER (See page EM−54 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010