1996 TOYOTA LAND CRUISER elec

N09214
DLC3
DI−134
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(9) After simulating the malfunction conditions, use the
TOYOTA hand−held tester diagnosis selector to
check the DTCs and freeze frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch off switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased. (10) After checking the DTC, inspect the applicable cir-cuit.
(b) Clear the DTC. The following actions will erase the DTCs and freeze
frame data.Operating the OBD II scan tool (complying with SAE
J1978) or TOYOTA hand−held tester to erase the
codes (See the OBD II scan tool’s instruction book
for operating instructions.).
NOTICE:
If the T OYOTA hand−held tester switches the ECM from the
normal mode to the check mode or vice−versa, or if the
ignition switch is turned from ON to ACC or OFF during the
check mode, the DTCs and freezed frame data will be
erased.
(c) Check the DLC3. The vehicle’s ECM uses V.P.W. (V ariable Pulse Width) for
communication to comply with SAE J1850. The terminal
arrangement of DLC3 complies with SAE J1962 and
matches the V.P.W. format.
Terminal No.Connection/V oltage or ResistanceCondition
2Bus  Line/Pulse generationDuring communication
4Chassis Ground − Body/1 Ω or lessAlways
5Signal Ground − Body/1 Ω or lessAlways
16Battery Positive − Body/9 − 14 V or 1 Ω or lessAlways
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−136
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
If the lock−up is defective:
Lock−up solenoid is stuck.
Lock−up control valve is stuck.
Lock−up signal value is stuck.
(2) In the same way, check the shock and slip at the 1 → 2, 2 →3 and 3 → O/D up−shift.
Evaluation:
If the shock is excessive:
Line pressure is too high.
Accumulator is defective.
Check ball is defective. (3) Run at the D position lock −up or O/D gear and check for abnormal noise and vibration.
HINT:
The check for the cause of abnormal noises and vibration must be made with \
extreme care as it could also
be due to loss of balance in the propeller shaft, differential, torque converter clutch, etc.
(4) While running in the D position, 2nd, 3rd and O/D gears, check to see that the\
possible kick −down
vehicle speed limits for 2 →1, 3 → 2 and O/D →3 kick−downs conform to those indicated on
the automatic shift schedule.
(5) Check for abnormal shock and slip at kick −down.
(6) Check for the lock −up mechanism.
Drive in D position, O/D gear, at a steady speed (lock −up ON) of about 95 km/h (59 mph).
Lightly depress the accelerator pedal and check that the engine RPM does not change
abruptly.
If there is a big jump in engine RPM, there is no lock −up.
(b) 2 position test. Shift into the 2 position and, while driving with the accelerator pedal held \
constantly at the full throttle
valve opening position, push in one of the pattern selectors and check the fo\
llowing points:
HINT:
When the 2nd start switch is on, there is no 1 → 2 up−shift and 2 →1 down−shift.
(1) Check to see that the 1 → 2 up− shift takes place and that the shift point conforms to the automatic
shift schedule.
HINT:
There is no O/D up−shift and lock−up in the 2 position. (2) While running in the 2 position and 2nd ge ar, release the accelerator pedal and check the engine
braking effect.
Evaluation:
If there is no engine braking effect:
2nd coast brake is defective. (3) Check for abnormal noise at acceleration and deceleration, and for shock at up −shift and down −
shift.
(c) L position test. (1) While running in the L position, check to see that there is no up −shift to 2nd gear.
(2) While running in the L position, release the accelerator pedal and check the engine braking ef- fect.
Evaluation:
If there is no engine braking effect:
1stand reverse brake is defective. (3) Check for abnormal noise during acceleration and deceleration.
(d) R position test. Shift into the R position and fully depress the accelerator pedal and ch\
eck for slipping.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07312
DI−142
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
9. MANUAL SHIFTING TEST
The purpose of this manual shifting test is to determine whether
a problem is caused by either mechanical or electrical factors.
Disconnecting the solenoid wire disables electrically −con-
trolled automatic gear shifting. In this case, operating the shift
lever is the only way to shift the transmission gear. If the gear
is not changed by shift lever operation, it is assumed that there
is a mechanical problem.
(a) Turn the ignition switch OFF.
(b) Disconnect the solenoid wire connector.
(c) Warm up the engine.
(d) Drive the vehicle.
(e) Check the transmission operation when the shift lever is moved into L, 2 and D positions.
Standard:
Shift LeverOperation
L to 2Shift up
2 to DShift up
D to 2Shift down
2 to LShift down
(f) Turn the ignition switch OFF.
(g) Connect the solenoid wire connector.
(h) Clear DTCs.
HINT:
When the solenoid wire is disconnected, the transmission gear
will be set as listed below:
Shift LeverGear
PParking
RReverse
NNeutral
DO/D (4th)
23rd
L1st
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KB−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−143
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the circuit listed for that code i\
n the table below and pro-
ceed to the page given.
DTC No.
(See page)Detection ItemTrouble AreaMIL*Memory
P0500
( DI−153 )Vehicle Speed Sensor Malfunc-
tion
(No. 1 Vehicle Speed Sensor)Open or short in No. 1 vehicle speed sensor circuit
 No. 1 vehicle speed sensor
 ECM

P0710
( DI−154 )Transmission Fluid Temperature
Sensor Malfunction
(ATF Temperature Sensor) Open or short in ATF temperature sensor circuit
 ATF temperature sensor
 ECM

P0750
( DI−156 )Shift Solenoid A Malfunction
(Shift Solenoid Valve No. 1)Shift solenoid valve No. 1 is stuck open or closed
 Valve body is blocked up or stuck
P0753
( DI−157 )Shift Solenoid A Electrical
Malfunction
(Shift Solenoid Valve No. 1)Open or short in shift solenoid valve No. 1 circuit
 Shift solenoid valve No. 1
 ECM

P0755
( DI−156 )Shift Solenoid B Malfunction
(Shift Solenoid Valve No. 2)Shift solenoid valve No. 2 is stuck open or closed
 Valve body is blocked up or stuck
P0758
( DI−157 )Shift Solenoid B Electrical
Malfunction
(Shift Solenoid Valve No. 2)Open or short in shift solenoid valve No. 2 circuit
 Shift solenoid valve No. 2
 ECM

P0770
( DI−161 )Shift Solenoid E Malfunction
(Shift Solenoid Valve SL)Shift solenoid valve SL is stuck open or closed
 Valve body is blocked up or stuck
 Lock− up clutch

P0773
( DI−163 )Shift Solenoid E Electrical
Malfunction
(Shift Solenoid Valve SL)Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM

P1700
( DI−166 ) Speed Sensor No. 2 Circuit
Malfunction
(No. 2 Vehicle Speed Sensor)Open or short in No. 2 vehicle speed sensor circuit
 No. 2 vehicle speed sensor
 ECM

P1780
( DI−169 )Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
 Park/neutral position switch
 ECM

*:  ...MIL light up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KD−02
Q08236
No. 1 Vehicle
Speed Sensor
O/D OFF Indicator Light
MIL
Pattern Select Switch O/D Main Switch
DLC1
Shift Solenoid Valve SL
ECM
Stop Light Switch L4 Position Sensor
Park/Neutral Position Switch No. 2 Vehicle Speed Sensor
Shift Solenoid Valve No. 2
Shift Solenoid Valve No. 1
Engine Coolant Temperature Sensor
Throttle Position Sensor
ATF Temperature Sensor
DLC3
Transfer Neutral
Position Switch
DI−144
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−146
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U) VTA (E5−
10) − E2 (E5− 9)
G−B − BR− BIG ON Accel. pedal is releasedBelow 0.3 − 0.8
IG ON Accel. pedal is depressed3.2 − 4.9
PWR (E7− 20)− E1 (E4− 24)P−B − BR− BIG ON Pattern select switch ”NORM”Below 1.5
IG ON Pattern select switch ”PWR”7.5 − 14
TFN (E7− 21)− E1 (E4− 24)Y−L − BR− BIG ON Transfer N positionBelow 3
IG ONTransfer other than N position9 − 14
L4SW (E7− 9)− E1 (E4− 24)B−L − BR− BIG ON Transfer L4 position7.5 − 14
IG ON Transfer other than L4 positionBelow 1.5
HOLD (E4−3) − E1 (E4− 24)O − BR− BIG ON 2nd start switch ON9 − 14
IG ON 2nd start switch OFFBelow 1.5
HI (E4−18) − E1 (E4− 24)R−W − BR− BIG ON7.5 − 14
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KH−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−147
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the diagnostic trouble code check but\
the trouble still occurs, check the
circuits for each symptom in the order given in the charts on the following pages and\
proceed to the page
given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1: Electronic Circuit Matrix Chart
Chapter 2: On−Vehicle repair Matrix Chart
Chapter 3: Off−Vehicle repair Matrix Chart
When troubleshooting, check Chapter 1 first. If instructions are given i\
n Chapter 1 to proceed to chapter 2
or 3, proceed as instructed.
(1) If the instruction ”Proceed to next circuit inspection shown on matrix chart” is given in the flow
chart for each circuit, proceed to the circuit with the next highest number in the table to cont\
inue
the check.
(2) If the trouble still occurs even though there are no abnormalities in any\
of the other circuits, then check and replace the ECM.
Chapter 1: Electronic Circuit Matrix Chart
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion6. On−vehicle repair matrix chart
7. Off −vehicle repair matrix chart−
−
Vehicle does not move in a particular position or positions1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No up− shift (1st → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up −shift (2nd → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up− shift (3rd → O/D)
1. O/D main switck& O/D OFF indicator light circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Throttle position sensor circuit
6. Park/neutral position switch circuit
7. O/D cancel signal circuit
8. Engine coolant temp. sensor circuit
9. On−vehicle repair matrix chart
10.Off −vehicle repair matrix chart
11. ECMDI−174
DI−157 DI−87
DI−166 DI−35
DI−169
DI−172 DI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−148
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
No down−
shift (O/D → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. ECMDI−157 DI−35
DI−87
DI−166 −
DI−145
No down −shift (3rd → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. ECMDI−157 DI−35
DI−87
DI−166 −
DI−145
No down −shift (2nd → 1st)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−157 DI−35
DI−87
DI−166 −
−
DI−145
Lock− up does not engage
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Stop light switch circuit
6. Park/neutral position switch circuit
7. Engine coolant temp. sensor circuit
8. On −vehicle repair matrix chart
9. Off −vehicle repair matrix chart
10.ECMDI−163
DI−35
DI−87
DI−166
DI−185
DI−169 DI−30 −
−
DI−145
Lock− up does not disengage
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Stop light switch circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chart
8. ECMDI−163 DI−35
DI−87
DI−166
DI−185 −
−
DI−145
Shift point too high or too low
1. Throttle position sensor circuit
2. Pattern select switch circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. ECMDI−35
DI−179 DI−87
DI−166
DI−145
Up− shifts to 2nd while in L position
Up− shifts to 3rd while in L position1. Park/neutral position switch circuit
2. ECMDI−169
DI−145
Up− shifts to O/D from 3rd while O/D main switch is OFF1. O/D main switck& O/D OFF indicator light circuit
2. ECMDI−174
DI−145
Up−shift to O/D from 3rd while engine is cold
1. Engine coolant temp. sensor circuit
2. On −vehicle repair matrix chart
3. Off −vehicle repair matrix chart
4. ECMDI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010