1996 TOYOTA LAND CRUISER ECU

DI−234
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
2 Check for open and short in harness and connector between ABS ECU and
DLC1, and DLC1 and body ground (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace ABS ECU.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W01184
BR−BGR−R
31 6 15
13
Ts
Ts
DLC1 ABS ECU
12 V
E1IH1 A12
EC
GR−R
F00007
Ts
DLC1
E1
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−235
1996 LAND CRUISER (RM451U)
Ts Terminal Circuit
CIRCUIT DESCRIPTION
The sensor check circuit detects abnormalities in the speed sensor signal which cannot be detecte\
d with
the DTC check. Connecting terminals Ts and E
1 of the DLC1 in the engine compartment starts the check.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminals Ts and E1 of DLC1.
CHECK:
(a) Turn the ignition switch ON.
(b) Measure the voltage between terminals Ts and E
1 of the
DLC1.
OK:
Voltage: 10 − 14 V
OK If ABS warning light does not blink even after Ts and E
1 are connected, ECU may be defective.
NG
DI5MN−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−236
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
2 Check for open and short in harness and connector between ABS ECU and
DLC1, and DLC1 and body ground (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace ABS ECU.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13679
BatteryFL BLOCK 2
MAIN
W
W
ECU−B
1
F/B
S7
B−R
2
3
SRS Warning
Light
8LA
Tc
B−Y8
IH1 Airbag Sensor
Assembly
DLC1
5 W−L
11
GENERATOR
(ALTERNATOR)
W
Cruise Control ECU
W−L
W−L
B−Y
B−Y
IH1 S7 S6
S6
Short Connector
Short Connector W−L
B−L
11
12
3
EA3 11
22
7
DI−274
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Always lit up, when igni-
tion switch is in LOCK position.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
DI5QD−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14677
Fuse
DI−276
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Does not light up, when
ignition switch is turned to ACC or ON.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
Refer to page DI−274 for the WIRING DIAGRAM.
INSPECTION PROCEDURE
1 Check ECU−B Fuse.
PREPARATION:
Remove ECU−B fuse.
CHECK:
Check continuity of ECU −B fuse.
OK:
Continuity
HINT:
Fuse may be burnt out even if it appears to be OK during
visual inspection.
If fuse is OK, install it.
NG Go to step 5.
OK
2 Preparation. (See step 1 on page DI−271)
DI5QE−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−278
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
5 Is new ECU−B fuse burnt out again?
NO Using simulation method, reproduce malfunc-
tion symptoms (See page IN−18 ).
YES
Check harness between ECU −B fuse and
SRS warning light.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O6-02
N06218CRUISE MAIN Indicator Light
BE4034
Indicator Light1.5 sec. 0.5 sec.
ON
OFF
N06219
TC
E1
DLC1
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI-286
1996 LAND CRUISER (RM451U)
PRE-CHECK
1. DIAGNOSIS SYSTEM
(a) Check the indicator.
(1) Turn the ignition switch to ON.
(2) Check that the CRUISE MAIN indicator light comeson when the cruise control main switch is turned on,
and that the indicator light goes off when the main
switch is turned OFF.
HINT:
If the indicator check result is not normal, proceed to trouble-
shooting (See page BE-34) for the combination meter section.
(b) Check the DTC.
HINT:
If a malfunction occurs in the No. 1 vehicle speed sensors or ac-
tuator, etc. during cruise control driving, the ECU actuates
AUTO CANCEL of the cruise control and turns on and off the
CRUISE MAIN indicator light to inform the driver of a malfunc-
tion. At the same time, the malfunction is stopped in memory as
a diagnostic trouble code.
(c) Output of DTC using diagnosis check wire. (1) Turn the ignition switch ON.
(2) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843-18020
(3) Read the DTC on the CRUISE MAIN indicator light.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4032
BE4033I00021
Normal Code
0.25 sec.
0.25 sec.
ON
OFF
ON
OFF
4 sec. 1.5 sec.
0.5 sec.
2.5 sec.0.5 sec.1.5 sec.
Malfunction codes 11 and 21
Code 11 Code 21
N09348
TOYOTA hand-held tester
TOYOTA Break-out-box
N18670
Instrument Panel Junction Block ECU- B
Fuse
DI-287
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
HINT:
If the DTC is not output, inspect the diagnosis circuit (See page
DI-333 )
As an example, the blinking patterns for codes; normal, 11 and
21 are shown in the illustration.
2. ECU TERMINAL VALUES MEASUREMENT BY USING TOYOTA BREAK-OUT-BOX AND TOYOTA HAND-
HELD TESTER
(a) Hook up the TOYOTA break- out- box and TOYOTA hand-held tester to the vehicle.
(b) Read the ECU input/output values by following the prompts on the tester screen.
(c) Please refer to the TOYOTA hand-held tester has a ºSnapshotº function. This records the measured data and
is effective in the diagnosis of intermittent problems.
3. DTC CLEARANCE
(a) After completing repairs, the diagnostic trouble code re- tained in memory can be cleared by removing the ECU-B
fuse for 10 seconds or more, with the ignition switch off.
(b) Check that the normal code is displayed after connecting the fuse.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010