1996 TOYOTA LAND CRUISER ECU

N14305
(1)
(1) (2)
No.
Operation Method CRUISE MAIN Indicator Light
Blinking Pattern Diagnosis
1 Turn SET/COAST switch ON
2 Turn RES/ACC switch ON
3 Turn CANCEL switch ON
Turn stop light switch ON
Depress brake pedal
Turn PNP switch OFF
(Shift to except D position)
4 Drive at about 40 km/h
(25 mph)or higher
Drive at about 40 km/h
(25 mph) or below
Light
ON
OFF
Light ON
OFF
Light ON
OFF Switch ON
Switch OFF
LightON
OFF Switch OFF
Switch ONSET/COAST switch circuit
is normal
RES/ACC switch circuit
is normal
CANCEL switch circuit
is normalStop light switch circuit
is normal
PNP switch circuit is
normal
Vehicle Speed Sensor is
normal
Light ON
OFF
Light
ON
OFF
1sec.
0.25 sec. 0.25 sec.
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI-290
1996 LAND CRUISER (RM451U)
5. INPUT SIGNAL CHECK
HINT:
(1) For check No.1 - No.3

Turn ignition switch ON.
(2) For check No.4

Jack up the vehicle.

Start the engine.

Shift to D position.
(a) Press the control switch to SET/COAST or RES/ACC position and hold it down or hold it up º1º.
(b) Push the main switch ON º2º.
(c) Check that the CRUISE MAIN indicator light blinks twice or 3 times repeatedly after 3 seconds.
(d) Turn the SET/COAST or RES/ACC switch OFF.
(e) Operate each switch as listed in the table below.
(f) Read the blinking pattern of the CRUISE MAIN indicator light.
(g) After performing the check, turn the main switch OFF.
HINT:
When 2 or more signals are input to the ECU, the lowest num-
bered code will be displayed first.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O7−02
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−291
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that cod\
e in the table
below and proceed to the appropriate page.
DTC No.
(See Page)Circuit inspectionTrouble Area
11
( DI−296 )Actuator Motor Circuit
Actuator motor
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
12
( DI−298 )Actuator Magnetic Clutch Circuit
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
13
( DI−301 )Actuator Position Sensor Circuit
Actuator position sensor
 Harness or connector between cruise control ECU and
actuator position sensor
 Cruise control ECU
14
( DI−304 )Actuator Mechanical Malfunction
Actuator motor (actuator lock: motor, arm)
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
21
( DI−306 )Open in Vehicle Speed Sensor Circuit
Combination meter
 Harness or connector between cruise control ECU and com-
bination meter, combination meter and vehicle speed sensor
 Vehicle speed sensor
 Cruise control ECU
23
( DI−310 )Vehicle Speed Signal AbnormalVehicle speed sensor
 Cruise control ECU
32
( DI−311 )Control Switch Circuit
Cruise control switch
 Harness or connector between cruise control ECU and cruise
control switch, cruise control switch and body ground
 Cruise control ECU
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O8−02
I00756
DLC1
Cruise Control Actuator
 Actuator Motor
 Actuator Magnetic Clutch
 Actuator Position Sensor
Cruise Control ECU
Cruise Control Switch
 Main Switch
 Control Switch
Stop Light Switch
No.1 V ehicle Speed Sensor
Park/Neutral Position Switch
Instrument Panel Fuse Block

GAUGE Fuse
 ECU−IG Fuse
 ECU− B Fuse
DI−292
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OA−02
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−295
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSee page
SET not occourring or CANCEL occurring.
(DTC is Normal)
1. Main Switch Circuit (Cruise control switch)
2. Vehicle Speed Sensor
3. Control Switch Circuit (Cruise control switch)
4. Stop Light Switch Circuit
5. Park/Neutral Position Switch Circuit
6. Actuator Motor Circuit
7. Cruise Control Cable
8. Cruise Control ECUDI−330
DI−306
DI−311
DI−314
DI−322
DI−296
DI−336 IN−28
SET not occurring or CANCEL occurring.
(DTC does not output)1. ECU Power Source Circuit
2. Cruise Control ECUDI−325IN−28
Actual vehicle speed deviates above or below the set speed.
1. Cruise Control Cable
2. Vehicle Speed Signal Abnormal
3. Electronically Controlled Transmission Communication
Circuit
4. Actuator Motor Circuit
5. Idle Signal Circuit (main throttle position sensor)
6. Cruise Control ECUDI−336
DI−310
DI−319
DI−296
DI−316IN−28
Gear shifting frequent between 3rd O/D when driving on uphill
road. (Hurting)1. Electronically Controlled Transmission Communication
Circuit
2. Cruise Control ECUDI−319
IN−28
Cruise control not cancelled, even when brake pedal is de-
pressed.
1. Cruise Control Cable
2. Stop Light Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−314
DI−296IN−28
Cruise control not cancelled, even when transmission is shifted to
”N” postion.
1. Cruise Control Cable
2. Park/Neutral Position Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−322
DI−296IN−28
Control switch does not operate.
(SET/COAST, A CC/RES, CANCEL not possible)
1. Cruise Control Cable
2. Control Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−311
DI−296 IN−28
SET possible at 40 km/h (25 mph) or less, or CANCEL does not
operate at 40 km/h (25 mph) or less.
1. Cruise Control Cable
2. Vehicle Speed Signal Abnormal
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−310
DI−296IN−28
Poor response is ACCEL and RESUME modes.
1. Cruise Control Cable
2. Electronically Controlled Transmission Communication
Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−319
DI−296IN−28
O/D does not RESUME, even though the road is not uphill.
1. Electronically Controlled Transmission Communication
Circuit
2. Cruise Control ECUDI−319
IN−28
DTC memory is erased.1. Back− up Power Source Circuit
2. Cruise Control ECUDI−328 IN−28
DTC is not output, or is output when is should not be.1. Diagnosis Circuit
2. Cruise Control ECUDI−319IN−28
Cruise MAIN indicator light remains ON or fall to light up.1. Cruise MAIN Indicator Light Switch CircuitDI−332
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OB−02
Duty Ratio =A + BA
x 100 (%)
ON
OFF A
B
1 cycle
I00488
Cruise Control ECU
MC
11
C17 MO
L
Cruise Control Actuator
L−RC17
7
6 12
C4
C4
DI−296
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
CIRCUIT INSPECTION
DTC 11 Actuator Motor Circuit
CIRCUIT DESCRIPTION
The actuator motor is operated by signals from the ECU. Acceleration and deceleration signals are trans-
mitted by changes in the Duty Ratio (See note below).
Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle. For e\
xample, if A is the period of continuity
in one cycle, and B is the period of non −continuity, then.
DTC No.Detection ItemTrouble Area
11Short in actuator motor circuit.
Actuator motor
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
WIRING DIAGRAM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00248
76
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−297
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check resistance between terminals MO and MC of actuator motor.
PREPARATION:
(a) Turn ignition switch OFF.
(b) Disconnect the actuator connector.
CHECK:
Measure resistance between terminals 6 and 7.
HINT:
If control plate position is fully opened or fully closed, resistance
can not measure.
OK:
Resistance: more than 4.2 Ω
NG Replace cruise control actuator.
OK
2 Check for open and short in harness and connectors between cruise contro\
l ECU and actuator motor (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU.
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00489
Cruise Control ECUL
L−
W−B
1
5
4 3
2 R
1026
C4 Stop Light Switch
4
R−G
Cruise
Control Actuator
C17
C17
C17
C4S13
S13 S13
S13
G−O G−WF11F11
1
2
STOP
Instrument Panel Fuse Block
W
EA3
W
3
1
F8
Battery Fusible Link
FL MAIN
STP−
DI−298
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
DTC 12 Actuator Magnetic Clutch Circuit
CIRCUIT DESCRIPTION
This circuit turns on the magnetic clutch inside the actuator during cruise \
control operation according to the
signal from the ECU. If a malfunction occurs in the actuator or speed sensor, etc. during cruise control opera-
tion, the rotor shaft between the motor and control plate is released.
When the brake pedal is depressed, the stop light switch turns on, supplying electrical power to the stop light.
Power supply to the magnetic clutch is mechanically cut and the magnetic clut\
ch is turned OFF.
When driving downhill, if the vehicle speed exceeds the set speed by 15 km/h\
(9 mph), the ECU turns the
safety magnet clutch OFF. If the vehicle speed later drops to within 10 km/h (6 mph) above the\
set speed,
then cruise control at the set speed is resumed.
DTC No.Detection ItemTrouble Area
12 Short in actuator magnetic clutch circuit.
 Open (0.8 sec.) in actuator magnetic clutch circuit.
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
WIRING DIAGRAM
DI5OC−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00247
4
5
DI−300
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
3 Check resistance between terminals L and GND of actuator magnetic clutch.
PREPARATION:
(a) Turn ignition switch OFF.
(b) Disconnect the actuator connector.
CHECK:
Measure resistance between terminals 4 and 5.
OK:
Resistance: 34.65 − 42.35 Ω.
NG Replace cruise control actuator.
OK
4 Check for open and short in harness and connectors between cruise contro\
l ECU and actuator magnetic clutch, actuator magnetic clutch and body grou\
nd
(See page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010