1996 TOYOTA LAND CRUISER Rear axle

−
INTRODUCTION TERMS
IN−35
35
Author: Date:
1996 LAND CRUISER (RM451U)
H/B
Hatchback
H−FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HPUHydraulic Power Unit
HSGHousing
HTHard Top
HWSHeated Windshield System
IACIdle Air Control
ICIntegrated circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, V
alve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
J/BJunction Block
J/CJunction Connector
KDKick−Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft−Hand
LHDLeft−Hand Drive
L/H/WLength, Height, Width
LLCLong− Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Dif ferential
LSP & PVLoad Sensing Proportioning And Bypass V alve
LSPVLoad Sensing Proportioning Valve
MAX.Maximum
M−FUSEMedium Current Fuse
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MPMultipurpose
MPXMultiplex Communication System
M/TManual Transmission (T ransaxle)
MTMount
MTGMounting
NNeutral
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN−36
−
INTRODUCTION TERMS
36
Author: Date:
1996 LAND CRUISER (RM451U)
NA
Natural Aspiration
No.Number
O/DOverdrive
OEMOriginal Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead V
alve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take−Off
R & PRack And Pinion
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight−Hand
RHDRight−Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear−Engine Rear −Wheel Drive
RRSRigid Rear Suspension
RWDRear− Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SMTSequential Manual T ransmission
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold−Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1DC−04
R05477
A
−
BRAKE LOAD SENSING PROPORTIONING AND BY− PASS
VALVE (LSP & BV)BR−45
1027
Author: Date:
1996 LAND CRUISER (RM451U)
ON−VEHICLE INSPECTION
1. SET REAR AXLE LOAD
Rear axle load (include vehicle weight):
1,330 kg (2,932 lb)
2. INSTALL LSPV GAUGE (SST) AND BLEED AIR SST 09709−29018
3. RAISE FRONT BRAKE PRESSURE TO 7,845 kPa (80 kgf/cm
2, 1,138 psi) AND CHECK REAR BRAKE PRES-
SURE
Rear brake pressure:
5,984 ± 589 kPa (61 ± 6 kgf/cm
2, 869± 86 psi)
HINT:
The brake pedal should not be depressed twice and/or returned
while setting to the specified pressure. Read the value of rear
pressure 2 seconds a fter adjusting the specified fluid pressure.
4. IF NECESSARY, ADJUST FLUID PRESSURE
(a) Disconnect the No.2 shackle from the shackle bracket.
(b) Adjust the length of the No.2 shackle turning it. Low pressure − Lengthen A.
High pressure − Shorten A
Initial set: 90 mm (3.54 in.)
Adjusting range: 84 − 96 mm (3.31 − 3.78 in.)
HINT:
One turn of the No.2 shackle changes the fluid pressure by
about 98.1 kPa (1.0 kgf/cm
2, 14.2 psi).
(c) In event the pressure cannot be adjusted by No.2 shackle, raise or lower the valve body.
Low pressure − Lower
High pressure − Raise
(d) Torque the 2 nuts. Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(e) Adjust the length of the No.2 shackle again.
If it cannot be adjusted, inspect the valve housing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1DH−01
R05477
A
BR−52−
BRAKE LOAD SENSING PROPORTIONING AND BY− PASS
VALVE (LSP & BV)
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL LSP & BV ASSEMBLY
Install the LSP & BV assembly to the frame with the 4 bolts. Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
2. CONNECT SHACKLE NO.2 TO BRACKET
(a) Set the dimension A by turning shackle No.2. Initial set: 90 mm (3.54 in.)
(b) Tighten the lock nut. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Install the 2 bushings and collar to the load sensing spring
shackle.
(d) Install the load sensing spring shackle to the shackle bracket with a retainer and nut.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(e) Install a new cotter pin.
3. CONNECT BRAKE LINES
Using SST, connect the 3 brake lines. SST 09751−36011
Torque: 15 N·m (155 kgf·cm, 11 ft·lbf)
4. SET REAR AXLE LOAD (See page BR−45 )
5. SET VALVE BODY
(a) When pulling down the load sensing spring, confirm that the valve piston moves down smoothly.
(b) Position the valve body so that the valve piston lightly contacts the load sensing spring.
(c) Tighten the 2 valve body mounting nuts. Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
6. BLEED BRAKE SYSTEM (See page BR−4 )
7. CHECK FLUID LEAKAGE
8. CHECK AND ADJUST LSP & BV FLUID PRESSURE (See page BR−45 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1DQ−02
BR−66
−
BRAKE REAR SPEED SENSOR
1996 LAND CRUISER (RM451U)
REMOVAL
HINT:
When replacing the sensor or sensor harness, replace the sen-
sor and sensor harness together as a set.
1. DISCONNECT SPEED SENSOR CONNECTOR
(a) Disconnect the speed sensor connector.
(b) Remove the 3 clamp bolts and 2 clips holding the sensor wire harness from the suspension arm and frame.
2. REMOVE SPEED SENSOR
Remove the installation bolt and speed sensor from the axle
end. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1NO−01
R04775
−
BRAKE REAR SPEED SENSOR
BR−67
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SPEED SENSOR
(a) Disconnect the speed sensor connector.
(b) Measure the resistance between terminals.
Resistance: 0.5 − 1.6 kΩ
If resistance value is not specified, replace the sensor.
(c) Check there is no continuity between each terminal and sensor body.
If there is continuity, replace the sensor.
(d) Connect the speed sensor connector.
2. INSPECT SENSOR INSTALLATION
Check the sensor installation bolt is tightened properly and
there is no clearance between the sensor and axle end.
If not, tighten the bolt. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
3. VISUALLY INSPECT SENSOR ROTOR SERRATIONS
(a) Remove the brake disc (See page BR−40).
(b) Inspect the sensor rotor serrations for scratches, cracks,
warping or missing teeth.
(c) Install the brake disc.
NOTICE:
To prevent damage to the serrations, do not strike the axle
hub.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R04759
R04775
BR3795
OKNG
-
DIAGNOSTICS ANTI-LOCK BRAKE SYSTEM
DI-214
1996 LAND CRUISER (RM451U)
4 Check sensor rotor and sensor installation.
Front
PREPARATION:
Remove front axle hub and knuckle spindle (See page
SA-8).
CHECK:
Check the sensor rotor serrations.
OK:
No scratches or missing teeth.
CHECK:
Check the sensor tip and grease.
OK:
No scratches or foreign objects on the sensor tip and
grease.
Rear
PREPARATION:
Remove the rear brake caliper and disc.
CHECK:
Check the sensor rotor serrations.
OK:
No scratches or missing teeth.
CHECK:
Check the sensor tip.
OK:
No scratches or foreign objects on the sensor tip.
CHECK:
Check the speed sensor installation.
OK:
The installation bolt is tightened properly and there is
no clearance between the sensor and steering
knuckle or rear axle carrier.
NG Replace speed sensor or rotor.
NOTICE:
Check the speed sensor signal last (See page DI-189).
OK
Check and replace ABS ECU.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL ENGINE UNIT
EM−79
1996 LAND CRUISER (RM451U)
16. Differential Side:
INSTALL FRONT AND REAR PROPELLER SHAFTS
(a) Align the matchmarks on the flanges and connect the
flanges with the 4 bolts and nuts.
(b) Torque the bolts and nuts. Torque:
74 N·m (750 kgf·cm, 54 ft·lbf) for front shaft
88 N·m (900 kgf·cm, 65 ft·lbf)for rear shaft
17. Transfer Side: INSTALL FRONT AND REAR PROPELLER SHAFTS
(a) Align the matchmarks on the flanges and connect the flanges with the 4 nuts.
(b) Torque the nuts. Torque:
74 N·m (750 kgf·cm, 54 ft·lbf) for front shaft
88 N·m (900 kgf·cm, 65 ft·lbf) for rear shaft
18. INSTALL STABILIZER BAR
(a) Temporarily install the stabilizer bar to the axle housing with the bolt and nut.
(b) Connect the stabilizer bar with the 2 bolts. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(c) Bounce the vehicle up and down to stabilize the suspen- sion.
(d) Torque the bolt and nut holding the stabilizer bar to the axle housing.
Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010