1996 TOYOTA LAND CRUISER Rear axle

SA1UK−01
Z15176
SST
R13186
SST
SA1973
SST
SA1969
SST
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
SA−21
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL
2. REMOVE FRONT PROPELLER SHAFT
(See page PR−3 )
3. REMOVE COMPANION FLANGE
(a) Using a chisel and hammer, loosen the staked part of the
nut.
(b) Using SST to hold the flange, remove the nut and plate washer.
SST 09330−00021
(c) Using SST, remove the companion flange. SST 09950−30010 (09951 −03010, 09953−03010,
09954 −03010, 09955 −03030, 09956−03020)
4. REMOVE OIL SEAL AND OIL SLINGER
(a) Using SST, remove the oil seal. SST 09308−10010
(b) Remove the oil slinger.
5. REMOVE REAR BEARING
Using SST, remove the rear bearing from the drive pinion. SST 09556−22010
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2430
SST
SA2271
R13155
SSTSST
Oil Storage Ring
Rear Bearing
SA2411
SST
1.0 mm (10.039 in.)
R13139
SST
SA−22
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
1996 LAND CRUISER (RM451U)
6. REMOVE REAR BEARING OUTER RACE
Using SST, remove the bearing outer race.
SST 09308−00010
NOTICE:
Do not scratch the taper surface of the outer race.
7. REMOVE OIL STORAGE RING
Using a screwdriver, bend the oil storage ring and drive it out.
8. REMOVE BEARING SPACER
9. INSTALL BEARING SPACER
10. INSTALL OIL STORAGE RING
Using SST, install a new oil storage ring. SST 09316−60011 (09316 −00011, 09316−00021)
11. INSTALL REAR BEARING
(a) Using SST, install the bearing outer race.
SST 09316−60011 (09316 −00011, 09316−00021)
(b) Install the rear bearing.
12. INSTALL OIL SLINGER AND OIL SEAL
(a) Install the oil slinger.
(b) Using SST, install a new oil seal, as shown. SST 09214−76011
Oil seal drive in depth: 1.0 mm (0.039 in.)
(c) Coat the lip of the oil seal with MP grease.
13. INSTALL COMPANION FLANGE
(a) Using SST, install the companion flange on the drive pin- ion.
SST 09950−30010 (09951 −03010, 09953−03010,
09954 −03010, 09955 −03030, 09956−03020)
(b) Place the plate washer on the companion flange.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1960
SST
RA1072
Filler Hole
Oil
0 − 5 mm (0 − 0.20 in.)
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
SA−23
1996 LAND CRUISER (RM451U)
(c) Apply light coat of gear oil on threads of a new companion
flange nut.
(d) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 196 N·m (2,000 kgf·cm, 145 ft·lbf)
14. ADJUST DRIVE PINION PRELOAD (See page SA−36 )
15. STAKE DRIVE PINION NUT
16. INSTALL FRONT PROPELLER SHAFT (See page PR−5 )
17. FILL DIFFERENTIAL WITH GEAR OIL Torque: 49 N·m (500 kgf·cm, 39 ft·lbf)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
Capacity:
w/o Differential lock:
2.80 liters (2.9 US qts, 2.5 Imp. qts)
w/ Differential lock:
2.65 liters (2.8 US qts, 2.3 Imp. qts)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W00530
w/o Differential LockSide Gear Thrust WasherPinion Gear
Pinion Gear Thrust Washer
 Dust Deflector
Front Bearing Outer Race
 Oil Seal
Companion Flange
Bearing Cap
Differential Carrier

Adjusting Nut Lock Oil Slinger
Differential Case
Drive Pinion
Ring Gear
Side Baring
Straight Pin
Adjusting Nut
 Bearing Spacer


Oil Storage Ring
Outer Race
Outer Race
 Non− reusable part 
Lock Plate
x 10
x 5 Pinion Shaft
Pinion Gear
Pinion Washer
Rear Bearing
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−25
882
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W00531
w/ Differential LockSide Gear
Thrust Washer
Pinion Gear
Thrust Washer
Outer Race

Oil Seal Companion Flange
Bearing Cap
Differential Carrier
 Adjusting Nut Lock Oil Slinger
Drive Pinion
Ring Gear
Side Baring
Adjusting Nut

Bearing Spacer

Oil Storage Ring
Outer Race
 Non− reusable part

Lock Plate x 8
x 4 
O− Ring
Pinion Washer
Rear Bearing

 Dust Deflector
Front Bearing Outer Race
Adjusting Nut
Sleeve
Spider Side GearLH Differential Case
RH Differential Case
x 8
 Precoated part 
Gasket Indicator Switch
Actuator

Straight Screw Plug
Spring Seat
Compression Spring
Ball

Shaft Retainer Shift Fork Shaft Shift Fork

Slotted Spring Pin
Pinion Gear
SA−26
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
883
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2405
SST
R13141
SST
SA2402
SST
Z00641
SST
R13142
Matchmarks
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−31
1996 LAND CRUISER (RM451U)
11. REMOVE COMPANION FLANGE
(a) Using a chisel and hammer, unstake the nut.
(b) Using SST to hold the flange, remove the nut and plate
washer.
SST 09330−00021
(c) Using SST, remove the companion flange. SST 09950 −30010 (09951 −03010, 09953 −03010,
09954 −03010, 09955 −03030, 09956−03020)
12. REMOVE OIL SEAL AND OIL SLINGER
(a) Using SST, remove the oil seal from the dif ferential carrier.
SST 09308−10010
(b) Remove the oil slinger.
13. REMOVE REAR BEARING
Using SST, remove the rear bearing from the drive pinion. SST 09556−22010
14. REMOVE DIFFERENTIAL CASE
(a) Place matchmarks on the bearing cap and dif ferential car-
rier.
(b) Remove the 2 adjusting nut locks.
(c) Remove the 4 bolts and 2 bearing caps.
(d) w/o Differential lock: Remove the 2 adjusting nuts.
(e) w/o Differential lock: Remove the differential case with the side bearing outer
races from the carrier.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FA2045
SST
SA2431
SST
Rear Bearing Outer Race
SA2410
Oil Strage Ring
Front Bearing
Outer Race
SA−32
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
HINT:
Tag the disassembled parts to show the location for reassemb-
ly.
(f) w/ Differential lock:
Remove the differential case with the side bearing outer
race, adjusting nuts and sleeve from the differential carri-
er.
(g) w/ Differential lock: Remove the shift fork.
15. REMOVE DRIVE PINION AND BEARING SPACER
(a) Remove the drive pinion with the front bearing.
(b) Remove the bearing spacer.
16. REMOVE DRIVE PINION FRONT BEARING
(a) Using SST and a press, remove the bearing from the drive
pinion.
SST 09950−00020
HINT:
If the drive pinion or ring gear are damaged, replace them as
a set.
(b) Remove the plate washer from the drive pinion.
17. REMOVE FRONT AND REAR BEARING OUTER
RACES AND OIL STORAGE RING
(a) Using SST, remove the rear bearing outer race. SST 09308−00010
(b) Using a brass bar and hammer, remove the oil storage ring and front bearing outer race.
HINT:
Do not remove the oil storage ring unless replacing it with a new
one.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2465
SA2406
SST
SA2203
SSTSST
Front
Rear
FA2042
SST
R13140
SST
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−39
1996 LAND CRUISER (RM451U)
7. CHECK RING GEAR RUNOUT
(a) Install the differential case onto the carrier and tighten the
adjusting nut just to where there is no play in the bearings.
(b) Using a dial indicator, check the ring gear runout. Maximum runout: 0.10 mm (0.0039 in.)
(c) Remove the differential case.
8. INSTALL OIL STORAGE RING
Using SST and a hammer, install a new oil storage ring. SST 09316−60011 (09316 −00011, 09316−00021)
9. INSTALL DRIVE PINION FRONT AND REAR BEARING
OUTER RACES
Front side:
Using SST and a press, install the 2 outer races.
SST 09316−60011 (09316 −00011, 09316−00051)
Rear side:
Using SST and a press, install the 2 outer races.
SST 09316−60011 (09316 −00011, 09316−00021)
10. INSTALL DRIVE PINION FRONT BEARING
(a) Install the plate washer on the drive pinion with the cham-
fered end facing the pinion gear.
(b) Using SST and a press, install the front bearing onto the
drive pinion.
SST 09506−30012
11. TEMPORARILY ADJUST DRIVE PINION PRELOAD
(a) Install the drive pinion, rear bearing and oil slinger.
HINT:
Assemble the spacer and oil seal after adjusting the gear con-
tact pattern.
(b) Install the companion flange with SST. SST 09550 −30010 (09951 −03010, 09953 −03010,
09954 −03010, 09955 −03030, 09956−03020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010