1996 LAND ROVER DEFENDER Workshop Manual

26COOLING SYSTEM
4
REPAIRREV: 05/99 AUXILIARY MOUNTING BRACKET AND GASKET
Service repair no - 26.50.04
Remove
1.Disconnect battery.
2.Drain cooling system
See Adjustment, Drain
and refill cooling system
.
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Remove viscous fan unit.
See Viscous
coupling and fan
6.Remove fan cowl.See Fan cowl
7.Slacken power steering pump pulley retaining
bolts.
8.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary Drive belt
9.Unscrew 3 bolts and remove power steering
pump pulley.
10.Remove 4 bolts securing power steering pump
mounting bracket.
11.Lower pump and bracket. Do not disconnect fluid
pipes.
12.Remove generator.
See ELECTRICAL, Repair,
Generator
13.Unscrew retaining nut and remove drive belt
tensioner.
14.Release hose clip from bracket above water
pump.15.Disconnect bottom hose/heater return hose at
water pump and heater rail.
16.Disconnect by-pass hose from water pump and
thermostat housing.
17.Remove 5 bolts (one with nut) and single
retaining nut, securing auxiliary mounting
bracket to cylinder block.
18.Withdraw mounting bracket, complete with water
pump.
19.Remove gasket and clean mating faces.
Refit
20.Using 2 slave studs, fit new gasket.
NOTE: All fixing bolts and nuts should be
tightened to
25 Nm (18 lbf/ft)unless
otherwise stated.
21.Locate mounting bracket, complete with water
pump on slave studs and secure with 4 other
fixings.
22.Remove slave studs and fit remaining bolts/nuts.
23.Fit by-pass hose to thermostat housing and
water pump.
24.Fit bottom hose/heater return hose to water
pump and heater rail.
25.Fit heater hose clip to mounting bracket.
26.Fit drive belt tensioner. Tighten nut to
45 Nm (33
lbf/ft).
27.Fit generator.See ELECTRICAL, Repair,
Generator
Do not fit drive belt at this stage.

COOLING SYSTEM
5
REPAIR 28.Secure steering pump and bracket to auxiliary
mounting bracket.
29.Fit steering pump pulley.
30.Fit drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
31.Fit fan cowl
See Fan cowl.
32.Fit viscous fan unit
See Viscous coupling and
fan
.
33.Fit intercooler top hose.
34.Fit radiator top hose.
35.Refill cooling system.
See Adjustment, Drain
and refill cooling system
36.Reconnect battery.THERMOSTAT
Service repair no - 26.45.01
Remove
1.Partially drain cooling system, until coolant level
is below thermostat housing.
2.Disconnect top hose from outlet elbow.
3.Disconnect electrical connections to water
temperature switch.
4.Unscrew 2 bolts and remove outlet elbow.
5.Withdraw thermostat. Note 88°C rating of
thermostat.
6.Place thermostat in a container half full of water.
Heat water and observe temperature at which
thermostat begins to open. Thermostat is
satisfactory if it opens between 85°-89°C.
Refit
7.Fit thermostat with jiggle pin/vent hole upwards.
8.Secure outlet elbow to thermostat housing.
Tighten bolts to
25 Nm (18 lbf/ft).
9.Fit water temperature switch connections.
10.Fit top hose to outlet elbow.
11.Refill cooling system.
See Adjustment, Drain
and refill cooling system

26COOLING SYSTEM
6
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Disconnect radiator bottom hose and drain
cooling system.
See Adjustment, Drain and
refill cooling system
2.Disconnect radiator top hose.
3.Remove viscous fan unit.
See Viscous
coupling and fan
4.Remove fan cowl.See Fan cowl
5.Disconnect oil cooler pipes. Plug all connections
to prevent oil spillage and ingress of dirt.
6.Disconnect top and bottom intercooler hoses.
7.Disconnect bleed hose at radiator.
8.Remove 2 bolts from both sides securing
radiator mounting brackets to bonnet platform.
9.Lift and remove radiator/intercooler assembly
from vehicle.
10.Remove 2 bolts from both sides and detach
radiator top cover from side covers.
11.Lift and remove radiator from intercooler and RH
side frame.
12.Check condition of locating grommets in radiator
top cover and lower mounting bushes. Renew if
necessary.Refit
13.Position radiator between intercooler and RH
side frame.
14.Fit radiator top cover to side covers.
15.Lower radiator/intercooler assembly into
position.
16.Secure radiator mounting brackets to bonnet
platform.
17.Fit radiator bleed hose.
18.Fit top and bottom intercooler hoses.
19.Fit oil cooler pipes.
20.Fit fan cowl
See Fan cowl.
21.Fit viscous fan unit.
See Viscous coupling
and fan
22.Fit radiator top hose.
23.Fit radiator bottom hose and refill cooling
system.
See Adjustment, Drain and refill
cooling system

COOLING SYSTEM
7
REPAIR EXPANSION TANK
Service repair no - 26.15.01
Remove
1.Position container to collect coolant spillage.
2.Slacken retaining clips and disconnect both
hoses from base of expansion tank.
3.Remove 3 bolts securing expansion tank to
inside wing and mounting bracket.
4.Remove expansion tank.
Refit
5.Fit expansion tank to inside wing and mounting
bracket.
6.Fit both hoses to base of tank.
7.Check and top up cooling system
See
SECTION 10, Maintenance, Under bonnet
maintenance

MANIFOLD AND EXHAUST SYSTEM
1
DESCRIPTION AND OPERATION MANIFOLDS AND EXHAUST SYSTEM
Description
The exhaust systems fitted on all models with the
300Tdi engine comprise three sections; front pipe
assembly, intermediate silencer assembly, and tail
pipe and silencer assembly. All sections, including
silencers, are manufactured from luminised steel to
give the system a durable working life under all
conditions. Special clamps are provided to ensureleak proof jointing between the various sections,
which are supported by flexible rubber mountings.
Catalytic convertor
When fitted, the catalytic converter is integral with the
front pipe assembly, which also incorporates a flexible
joint. The catalyst forms part of the engine emission
control that can also include an EGR valve system
See FUEL SYSTEM, Repair, EGR valve
Exhaust system - 90
1.Gasket
2.Front pipe
3.Front pipe with catalytic converter
4.Front mounting bracket
5.Intermediate silencer6.Intermediate mounting brackets
7.Tail pipe silencer*
8.Tail pipe silencer mounting
9.Tail pipe mounting
* Deleted on later models

30MANIFOLD AND EXHAUST SYSTEM
2
DESCRIPTION AND OPERATION The catalyst comprises platinum coated ceramic
elements. The Hydrocarbons (HC), Oxides of nitrogen
(NOx) and Carbon monoxide (CO) emitted by the
engine react with the catalytic element and exhaust
temperature to convert the toxic gas into Nitrogen
(N
2), Carbon dioxide (CO2) and water vapour.
Exhaust system - 110/130
1.Gasket
2.Front pipe
3.Front pipe with catalytic converter
4.Front mounting bracket
5.Intermediate silencer6.Intermediate mounting brackets
7.Tail pipe silencer
8.Tail pipe silencer mounting
9.Tail pipe mounting

MANIFOLD AND EXHAUST SYSTEM
1
REPAIR INDUCTION MANIFOLD
Service repair no - 30.15.02
Remove
1.Disconnect battery.
2.Remove oil filler cap and remove rocker cover
insulation.
3.Remove hose intercooler to induction manifold. If
fitted, remove EGR valve.
See FUEL SYSTEM,
Repair, EGR valve
4.Remove 2 screws and release heat shield from
induction manifold.
5.Slacken induction manifold lower securing nuts,
located below exhaust manifold.
6.Remove induction manifold upper securing bolts.
7.Remove induction manifold. Plug apertures in
cylinder head with clean rag to prevent any items
falling into engine.
8.Check gasket is satisfactory for further use.
Refit
9.Clean induction manifold mating face.
10.Position induction manifold and secure with
upper and lower fixings.
11.Tighten securing nuts and bolts to
25 Nm (18
lbf/ft).
12.Fit manifold heat shield.
13.Fit hose intercooler to induction manifold.
14.Fit rocker cover insulation.
15.Reconnect battery.INDUCTION/EXHAUST MANIFOLD GASKET
Service repair no - 30.15.15
Remove
1.Remove induction manifold
See Induction
manifold
.
2.Remove turbocharger outlet hose.
3.Raise vehicle and slacken exhaust front pipe to
intermediate silencer flange nuts. Ensure pipe is
free to turn.
NOTE: If removing exhaust manifold and
turbocharger assembly from vehicle,
remove manifold to exhaust front pipe
nuts while working under vehicle.
4.Remove exhaust manifold securing nuts,
removing centre lower nut first.
5.Move heater rail clear of exhaust manifold.
6.With exhaust manifold and turbocharger still
attached to exhaust front pipe, withdraw from
head by turning front pipe until sufficient access
is gained to remove gasket.
7.Suitably support exhaust manifold and
turbocharger assembly to prevent damage.
8.Remove induction manifold lower nuts.
9.Remove gasket.
10.Clean mating faces.

30MANIFOLD AND EXHAUST SYSTEM
2
REPAIR Refit
11.Fit new gasket over manifold studs.
12.Loosely fit induction manifold lower nuts to
studs.
13.Fit exhaust manifold and secure with central
upper and lower nuts.
14.Locate heater rail to its correct position and
secure with outer exhaust manifold nuts.
15.Tighten all exhaust manifold nuts to
45 Nm (33
lbf/ft).
16.Tighten exhaust front pipe to intermediate
silencer nuts to
50 Nm (37 lbf/ft).
17.Fit turbocharger outlet pipe.
18.Fit induction manifold
See Induction manifold
.EXHAUST MANIFOLD/TURBOCHARGER
ASSEMBLY
Service repair no - 30.15.10
Remove
1.Remove induction manifold
See Induction
manifold
.
2.Disconnect turbocharger inlet hose.
3.Disconnect boost pressure pipe at turbocharger.
4.Remove intercooler bottom hose.
5.Place suitable container under engine and
disconnect turbocharger oil feed and return
pipes at cylinder block.
6.Remove 3 nuts securing exhaust front pipe to
manifold flange.
7.Remove 7 nuts and lift exhaust manifold and
turbocharger assembly from cylinder head.
8.Discard manifold gasket.
Refit
9.Fit new manifold gasket.
10.Position exhaust manifold assembly onto
location studs and secure to cylinder head.
Tighten nuts to
45 Nm (33 lbf/ft).
11.Secure exhaust front pipe to manifold flange.
Tighten fixings to
50 Nm (37 lbf/ft).
12.Reconnect turbocharger oil feed and return
pipes at cylinder block.
13.Fit intercooler bottom hose.
14.Fit boost pressure pipe at turbocharger.
15.Fit turbocharger inlet hose.
16.Fit induction manifold
See Induction manifold
.