1996 LAND ROVER DEFENDER wheel size

01INTRODUCTION
4
INFORMATIONREV: 05/99 ACCESSORIES AND CONVERSIONS
DO NOT FITunapproved accessories or conversions,
as they could affect the safety of the vehicle.
Land Rover will not accept liability for death, personal
injury, or damage to property which may occur as a
direct result of the fitting of non-approved conversions
to the vehicle.
WHEELS AND TYRES
WARNING: DO NOT replace the road
wheels with any type other than genuine
Land Rover wheels which are designed for
multi-purpose on and off road use and have very
important relationships with the proper operation
of the suspension system and vehicle handling.
Replacement tyres must be of the make and sizes
recommended for the vehicle, and all tyres must
be the same make, ply rating and tread pattern.
STEAM CLEANING
To prevent consequential rusting, any steam cleaning
within the engine bayMUSTbe followed by careful
re-waxing of the metallic components affected.
Particular attention must be given to the steering
column, engine coolant pipes and hose clips.
SPECIFICATION
The specification details and instructions set out in
this Manual apply only to a range of vehicles and not
to any one. For the specification of a particular vehicle
purchasers should consult their Dealer.
The Manufacturer reserves the right to vary
specifications with or without notice, and at such times
and in such manner as it thinks fit. Major as well as
minor changes may be involved in accordance with
the Manufacturer's policy of constant product
improvement.
Whilst every effort is made to ensure the accuracy of
the particulars contained in this Manual, neither the
Manufacturer or Dealer, by whom this Manual is
supplied, shall in any circumstances be held liable for
any inaccuracy or the consequences thereof.SPECIAL SERVICE TOOLS
The use of approved special service tools is
important. They are essential if service operations are
to be carried out efficiently, and safely. Where special
tools are specified,only these tools should be used
to avoid the possibility of personal injury or
damage to the components.Also, the amount of
time which they save can be considerable.
Special tools bulletins will be issued periodically giving
details of new tools as they are introduced.
All orders and enquiries from the United Kingdom
should be sent direct to Cartool (UK) Ltd. Overseas
orders should be placed with the local Cartool
distributor, where one exists. Countries where there is
no distributor may order direct from:
Cartool (UK) Ltd.
Unit 3,
Sterling Business Park,
Brackmills,
Northampton,
England, NN4 7EX.
The tools recommended in this Workshop Manual are
listed in an illustrated catalogue, obtainable from:
Land Rover Publications,
Character Mailing,
Heysham Road,
Bootle,
Merseyside, L70 1JL
COPYRIGHT
Ó1999 Rover Group Limited
All rights reserved. No part of this publication may be
produced, stored in a retrieval system or transmitted
in any form, electronic, mechanical, recording or other
means without prior written permission of Rover
Group.

GENERAL SPECIFICATION DATA
11
INFORMATION REV: 05/99 TYRE SIZE AND PRESSURES
90 models Front Rear
Normal - all load conditions
205 R16 radial
& 265/75 R16 (multi-terrain)1,9 bar .................................. 2,4 bar
28 Ibf/in
235 Ibf/in2
2,0 kgf/cm22,5 kgf/cm2
750 R16 radial1,9 bar ........................................................ 2,75 bar
28 Ibf/in240 Ibf/in2
2,0 kgf/cm22,8 kgf/cm2
110 models
Normal - all load conditions
750 R16 Radial1,9 bar ....................................................... 3,3 bar
28 Ibf/in
248 Ibf/in2
2,0 kgf/cm23,4 kgf/cm2
130 models
Normal - all load conditions
750 R16 Radial3,0 bar ....................................................... 4,5 bar
44 Ibf/in
265 Ibf/in2
3,1 kgf/cm24,6 kgf/cm2
WARNING: Tyre pressures must be
checked with the tyres cold, as the
pressure is about 0,21 bar (3 Ibf/in
2, 0,2
kgf/cm2) higher at running temperature. If the
vehicle has been parked in the sun or high
ambient temperatures, DO NOT reduce the tyre
pressures, move the vehicle into the shade and
wait for the tyres to cool before checking the
pressures.
WHEELS
90 models
Steel wheel size:
Heavy duty - UK and Western Europe 6.5F X 16.............................
Other markets 5.5F X 16..................................................................
Alloy wheel size 7J X 16................................................................
110 models
Steel wheel size:
Heavy duty - UK and Western Europe 6.5F X 16.............................
Other markets 5.5F X 16..................................................................
130 models
Steel wheel size:
Heavy duty - UK and Western Europe 6.5F X 16.............................
Other markets 5.5F X 16..................................................................
WARNING: Always use the same make and
type of radial-ply tyres, front and rear. DO
NOT use cross-ply tyres, or interchange
tyres from front to rear.
·If the the wheel is marked 'TUBED', an inner
tube MUST be fitted, even with a tubeless tyre.
·If the wheel is marked 'TUBELESS', an inner
tube must NOT be fitted.

57STEERING
2
ADJUSTMENT STEERING LOCK STOPS
Service repair no - 57.65.03
Check
1.Measure clearance between tyre wall and radius
arm at full lock. This must be not less than 20
mm.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check clearance between tyre wall and radius
arm on each lock.
NOTE: Alternatively lock stop adjustment
may be carried out using following
procedure.
Check
1.Measure stop bolt protrusion 'A'. Refer to table
for correct setting.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check wheel position at full lock.LOCK STOP SETTINGS
Tyre & wheel size - alloys
Make Size Setting
BF Goodrich Mud Terrain 265 59,7 mm
Goodyear GT+4 235 55,7 mm
Michelin M+S 4x4 235 54,2 mm
Tyre & wheel size - steel
Make Size Setting
Goodyear 205 52,2 mm
Michelin 205 52,2 mm
Avon 7.50 56 mm
Michelin 7.50 56 mm
Goodyear 7.50 56 mm

WHEELS AND TYRES
1
DESCRIPTION AND OPERATION TYPES OF WHEEL RIMS AND TYRES
Description
Dependent on specification and model type, the
vehicle is equipped with pressed steel or alloy wheel
rims, both using tubeless radial ply tyres.
Tyre codes
The text, codes and numbers moulded into the tyre
wall vary between tyre manufacturers, however most
tyres are marked with the information shown in the
illustrated example.
NOTE: The illustration is an example of the
type of markings moulded into tyres and is
for guidance only. For specific tyre
specifications
See GENERAL SPECIFICATION
DATA, Information, Tyre size and pressures
.1.Type of tyre construction -Radial Ply
2.Load index -104
3.Speed symbol -SorT
4.USA Tyre quality grading -Tread wear 160
Traction A temperature B
5.Tread wear indicators moulded into tread pattern
are located at intervals around the tyre and
marked by a code -E66 103S6
6.Tyres with 'Mud Snow' type tread pattern are
marked -M&S
7.Tyre reinforcing mark -Reinforced
8.USA Load and pressure secification -
(900Kg(1984LBS) at 340KA (50PSI) MACS
PRESS
9.Tyre size -205 16 ot 235/70 R16
10.Type of tyre -TUBELESS
11.Country of manufacture -MADE IN GREAT
BRITAIN
12.USA Compliance symbol and identification -
DOT AB7C DOFF 267
13.European type approval identification -E11
01234
14.Tyre construction -SIDE WALL 2 PLIES
RAYON. TREAD 2 RAYON 2 STEEL
15.Manufacturers brand name/type -TRACTION
PLUS mzx M

WHEELS AND TYRES
1
REPAIR REV: 05/99 GENERAL INFORMATION
WARNING: This is a multi-purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels. The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim
See
Tyre Fitting
.
WARNING: DO NOT fit an inner tube to an
alloy wheel.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment,
See Fault
diagnosis, Tyre Wear Chart
, if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration above.
When the tread has worn to a depth of 1.6 mm the
indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration above.