1996 LAND ROVER DEFENDER change time

01INTRODUCTION
4
INFORMATIONREV: 05/99 ACCESSORIES AND CONVERSIONS
DO NOT FITunapproved accessories or conversions,
as they could affect the safety of the vehicle.
Land Rover will not accept liability for death, personal
injury, or damage to property which may occur as a
direct result of the fitting of non-approved conversions
to the vehicle.
WHEELS AND TYRES
WARNING: DO NOT replace the road
wheels with any type other than genuine
Land Rover wheels which are designed for
multi-purpose on and off road use and have very
important relationships with the proper operation
of the suspension system and vehicle handling.
Replacement tyres must be of the make and sizes
recommended for the vehicle, and all tyres must
be the same make, ply rating and tread pattern.
STEAM CLEANING
To prevent consequential rusting, any steam cleaning
within the engine bayMUSTbe followed by careful
re-waxing of the metallic components affected.
Particular attention must be given to the steering
column, engine coolant pipes and hose clips.
SPECIFICATION
The specification details and instructions set out in
this Manual apply only to a range of vehicles and not
to any one. For the specification of a particular vehicle
purchasers should consult their Dealer.
The Manufacturer reserves the right to vary
specifications with or without notice, and at such times
and in such manner as it thinks fit. Major as well as
minor changes may be involved in accordance with
the Manufacturer's policy of constant product
improvement.
Whilst every effort is made to ensure the accuracy of
the particulars contained in this Manual, neither the
Manufacturer or Dealer, by whom this Manual is
supplied, shall in any circumstances be held liable for
any inaccuracy or the consequences thereof.SPECIAL SERVICE TOOLS
The use of approved special service tools is
important. They are essential if service operations are
to be carried out efficiently, and safely. Where special
tools are specified,only these tools should be used
to avoid the possibility of personal injury or
damage to the components.Also, the amount of
time which they save can be considerable.
Special tools bulletins will be issued periodically giving
details of new tools as they are introduced.
All orders and enquiries from the United Kingdom
should be sent direct to Cartool (UK) Ltd. Overseas
orders should be placed with the local Cartool
distributor, where one exists. Countries where there is
no distributor may order direct from:
Cartool (UK) Ltd.
Unit 3,
Sterling Business Park,
Brackmills,
Northampton,
England, NN4 7EX.
The tools recommended in this Workshop Manual are
listed in an illustrated catalogue, obtainable from:
Land Rover Publications,
Character Mailing,
Heysham Road,
Bootle,
Merseyside, L70 1JL
COPYRIGHT
Ó1999 Rover Group Limited
All rights reserved. No part of this publication may be
produced, stored in a retrieval system or transmitted
in any form, electronic, mechanical, recording or other
means without prior written permission of Rover
Group.

MANUAL GEARBOX
1
ADJUSTMENT GEAR CHANGE LEVER BIAS SPRING - ADJUST
Service repair no - 37.16.26
1.Remove gear lever and transfer box lever knobs.
2.Remove gear lever cover.
3.Remove nut and washer securing gear lever.
4.Mark gear lever spline setting, remove lever and
gaiter from lower lever.
5.Remove insulation pad from tunnel aperture.
6.Fit gear lever and select 3rd or 4th gear.
7.Slacken adjustment screw locknuts.
8.Adjust screws until both legs of bias springs are
approximately 0.5mm clear of gear lever cross
pin.
9.Apply a slight load to gear lever in a LH direction
and adjust RH screw downward until RH spring
leg just makes contact with cross pin.
10.Repeat procedure for LH adjustment screw.
11.Lower both adjustment screws equal amounts
until radial play is eliminated.
12.Tighten locknuts.
13.Return gear lever to neutral position and rock
across gate several times. The gear lever should
return to 3rd and 4th gate.
14.Remove gear lever.
15.Fit insulation pad.
16.Locate gaiter over lower lever and bias springs.
17.Fit gear lever to lower lever spline, secure with
new nyloc nut and tighten to
25 Nm (18 lbf/ft).
18.Fit gear lever cover.
19.Fit gear lever and transfer box lever knobs.

57STEERING
10
FAULT DIAGNOSISREV: 05/99 VISUAL AND SAFETY CHECKS
WARNING: Before taking vehicle out on
the public highway for road test, it is
important that the following basic visual
checks are carried out to ensure that the vehicle
complies with legal requirements.
Tyres and wheel rims
1.Check and adjust tyre pressures
See
GENERAL SPECIFICATION DATA,
Information, Tyre Pressures
.
Note that this information refers to standard tyres
fitted as original equipment.
2.Check condition of tyres. Inspect for signs of
uneven wear, damage and feathering. Check
tread depth.
3.Ensure that the tyre make, type and general
condition are common across each axle.
4.Check wheel rims for signs of damage and
excessive run out.
5.Carry out road test
See Road Test Procedure
.
ROAD TEST PROCEDURE
General steering/handling problems can usually be
classified into one of the categories listed and ARE
GENERALLY RELATED TO THE AGE, CONDITION
AND USE OF THE VEHICLE.
WARNING: Ensure that all road tests are
conducted by suitably qualified drivers in
a safe and legal manner, and where local
traffic conditions allow.
1.Carry out visual and safety checks
See Visual
and Safety Checks
.
Confirm general nature of complaint with customer,
simulating where possible the conditions under which
the problem occurs. Carry out following road test
procedure to establish the problem.2.Steering load assessment - drive at 16 km/h (10
mph). Put 90°turn input into steering wheel,
check self centering. The self centering should
be equal on each lock but not necessarily return
to exactly straight ahead without assistance from
the driver.
3.Steering assessment - drive at 64 km/h (40 mph)
on a staight FLAT road (no camber), check for
steering veer. The vehicle should follow a
straight path with NO tendency to follow a
curved path. If vehicle veers towards the kerb,
vehicle may be 'camber sensitive'. A small
amount of veer in direction of camber is
acceptable.
4.Directional stability assessment - drive at 112
km/h (70 mph) or maximum legal speed on a
straight flat road. Carry out a normal lane
change. Vehicle should quickly settle into a new
straight path.
5.Braking assessment (medium effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply
steady medium braking effort, noting any
tendency to veer. Carry out brake test three
times, if a veer is consistently noted carry out a
braking efficiency test on a rolling road.
6.Braking assessment (full effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply full
braking effort, noting any tendency to veer. Carry
out brake test three times, if a veer is
consistently noted carry out a braking efficiency
test on a rolling road.
If the symptom described by the customer is stiff
steering or steering niggle, carry out stiff steering
procedure
See Stiff Steering Checklist.
If not, proceed with basic checks and adjustments
See Visual Check and Basic Adjustments.