GENERAL SPECIFICATION DATA
3
INFORMATION FUEL SYSTEM
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 Kgf/cm
2(3 - 4 lbf/in2) at 1800 rpm .....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter, 1.29:1 drive.......................................................................
ratio, with viscous coupling.
Pump type Centrifugal, impellor, belt driven........................................................................
Thermostat opening 88°C .........................................................
Expansion tank cap pressure 1,06 Kgf/cm
2(15 Ibf/in2) (system pressure) ...........................................
CLUTCH
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................
TRANSMISSION
Main gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward, 1 reverse, all synchromesh.............................................................................
Transfer box
Type LT230 Two speed reduction on main gearbox output. Front......................................................................
and rear drive permanently engaged via a lockable
differential
Rear axle
Type Spiral bevel, fully floating shafts.................................................................................
Ratio 3.54:1.................................................................................
MAINTENANCE
3
MAINTENANCE UNDER BONNET MAINTENANCE
UNDER BONNET COMPONENTS
A - RH drive
1.Brake fluid reservoir
2.Clutch fluid reservoir
3.Air cleaner element
4.Engine breather filter
5.Oil filler cap
6.Oil level dipstick
7.Heater/air conditioning unit
8.Windscreen washer reservoir
9.Power steering pump reservoir10.Intercooler and hoses
11.Radiator filler plug
12.Radiator
13.Oil cooler
14.Fuel filter
15.Accelerator linkage
16.Expansion tank
17.Air cleaner dump valve
10MAINTENANCE
4
MAINTENANCE
UNDER BONNET COMPONENTS
B - LH drive
1.Brake fluid reservoir
2.Clutch fluid reservoir
3.Air cleaner element
4.Engine breather filter
5.Oil filler cap
6.Oil level dipstick
7.Heater/air conditioning unit
8.Windscreen washer reservoir
9.Power steering pump reservoir10.Intercooler and hoses
11.Radiator filler plug
12.Radiator
13.Oil cooler
14.Fuel filter
15.Accelerator linkage
16.Expansion tank
17.Air cleaner dump valve
MAINTENANCE
5
MAINTENANCE REV: 05/99 CHECK COOLING, INTERCOOLING AND HEATING
SYSTEMS
Check cooling, and heater systems for leaks and
pipes/hoses for security and condition. Refill or top up
as necessary.
CAUTION: It is important that the correct
procedure is followed when refilling or
topping up the cooling system to avoid
trapping air in the system.
WARNING: Do not remove caps and plugs
when engine is hot because cooling
system is pressurised and personal
scalding could result.
1.Remove plastic plugs from thermostat housing
and radiator.
2.Fill cooling system with correct concentration
and specification of anti-freeze.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
3.Fill from expansion tank until radiator is full, with
level in expansion tank the same as in radiator.
NOTE: Care should be taken to avoid
excess coolant spillage from radiator.
4.Fit plastic plug in radiator.
5.Add a further 1 litre (1.76 pints) of coolant to
expansion tank and allow to settle.
6.Refit expansion tank cap and thermostat
housing plug.
7.Run engine at idle speed for five minutes.
8.Switch off engine, check that expansion tank
coolant is level with top of indicator post and top
up as necessary.Check intercooler and turbo-charger system for air
leaks and pipes/hoses for security and condition.
All system hoses should be renewed at first signs of
deterioration.
VALVE CLEARANCES - CHECK/ADJUST
Check/adjust valve clearances.
See ENGINE ,
Adjustment, Valve clearances - check and adjust
RENEW FUEL FILTER ELEMENT
Remove
1.Clean area around filter head and position a
container beneath.
2.Unscrew and remove filter, catch fuel released.
Refit
3.Wet seal of new filter with fuel.
4.Screw new filter into position.
5.Ensure drain tap is fully closed.
10MAINTENANCE
6
MAINTENANCE RENEW AIR CLEANER ELEMENT AND CLEAN
DUMP VALVE
Remove
1.Release 2 retaining clips and lift air cleaner from
its cradle sufficiently to gain access to element.
2.Unscrew wing nut and remove end cover.
3.Unscrew second wing nut and withdraw element
from air cleaner casing.
4.Clean interior and exterior of casing and cover.
5.Squeeze open dump valve and check that
interior is clean. Renew valve, if perished.Refit
6.Fit new element, seal first, into casing and
secure with wing nut.
7.Fit end cover, align mating arrows, and secure
with wing nut.
8.Position air cleaner in mounting cradle and
secure with retaining clips.
CLEAN ENGINE BREATHER FILTER
Remove
1.Disconnect breather top hose.
2.Remove single bolt and ease breather from
rocker cover.
3.Disconnect bottom hose and remove engine
breather.
4.Using suitable flushing solvent, thoroughly clean
breather filter. Remove and discard rubber 'O'
ring from breather pipe.
Refit
5.Fit new rubber 'O' ring to engine breather.
6.Connect breather bottom hose.
7.Locate breather into rocker cover and secure
with retaining bolt, tightening to
9 Nm (7 lbf/ft).
8.Connect breather top hose.
MAINTENANCE
9
MAINTENANCE REV: 05/99 UNDER VEHICLE MAINTENANCE
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
maintenance, or remove and refit procedures are
required, it may be necessary to remove the
undertray and/or integral access panels
See
CHASSIS AND BODY, Repair, Front undertray
or
See CHASSIS AND BODY, Repair, Rear undertray
RENEW ENGINE OIL AND FILTER
1.Ensure vehicle is level.
2.Run engine to warm oil, switch off ignition.
3.Disconnect battery.
4.Place suitable drain tray under sump drain plug.
5.Remove drain plug from sump and allow oil to
drain completely.
6.Fit new sealing washer, replace plug and tighten
to
35 Nm (26 lbf/ft).
7.Place drain tray under oil filter.
8.Unscrew filter anti-clockwise, using a strap
wrench if necessary.
9.Clean mating face of oil filter adaptor.
10.Coat rubber sealing washer of new filter with
clean engine oil.
11.Screw filter on clockwise until sealing washer
touches adaptor mating face, tighten a further
half turn by hand only. DO NOT overtighten.
12.Clean and remove filler cap from rocker cover.
13.Pour in correct quantity and grade of new oil
from a sealed container.
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
14.Check that oil level is between upper and lower
marks on dipstick. DO NOT fill above upper
mark.
15.Firmly replace filler cap.
16.Reconnect battery, run engine and check oil filter
for leaks.
17.Stop engine, allow oil to run back into sump for a
few minutes and check oil level again. Top up if
necessary.
10MAINTENANCE
12
MAINTENANCEREV: 05/99 LUBRICATE PROPELLER SHAFT UNIVERSAL
AND SLIDING JOINTS
1.Clean all grease nipples on front and rear
propeller shafts.
2.Using a low pressure hand grease gun, apply
recommended grease
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
to grease
nipples at front and rear propeller shaft universal
and sliding joints.
VISUALLY CHECK BRAKE, FUEL, CLUTCH
HOSES/PIPES/UNIONS FOR CHAFING, LEAKS
AND CORROSION
CHECK EXHAUST SYSTEM FOR LEAKS,
SECURITY AND DAMAGE
RENEW CATALYTIC CONVERTERS
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
manifolds and exhaust system
CHECK FOR FLUID LEAKS FROM POWER
STEERING AND SUSPENSION SYSTEMS,
HYDRAULIC PIPES AND UNIONS FOR CHAFING
AND CORROSION
CHECK/TIGHTEN STEERING UNIT AND STEERING
ROD BALL JOINT FIXINGS, CHECK CONDITION
OF BALL JOINTS AND DUST COVERSBall joints are lubricated for life during manufacture
and require no further lubrication unless the rubber
boot has been dislodged or damaged. All joints should
be checked at specified service intervals, but more
frequently if vehicle is used under arduous conditions.
1.Check for wear in joints by moving ball joint up
and down vigorously. If free movement is
apparent, fit a new joint assembly.
See
STEERING, Repair, Drop arm ball See
STEERING, Repair, Track rod and See
STEERING, Repair, Drag link and drag link
ends
CHECK/TIGHTEN FRONT AND REAR AXLE
SUSPENSION LINK FIXINGS, CHECK CONDITION
OF MOUNTING RUBBERS
DRAIN AND CLEAN FUEL SEDIMENTER, IF
FITTED
The fuel sedimenter is located on a chassis side
member on the RH side of vehicle near rear wheel. It
increases the working life of the fuel filter by removing
larger droplets of water and other matter from fuel.
NOTE: On 110/130 models with a twin tank
fuel system, two sedimenters may be
fitted, one on each side of the vehicle
chassis.
1.Slacken drain plug and allow any water to drain
off.
ENGINE
5
REPAIR
26.Disconnect both pipes from fuel lift pump.
27.Release fuel feed pipe from retaining clip on air
cleaner bracket.
28.Disconnect vacuum hose from brake servo.
29.Remove oil pipes from oil filter adaptor.30.Using suitable hoist, fit chains to lifting brackets
and support engine.
31.Remove nuts and plain washers securing front
engine mountings to chassis.
32.Support gearbox.
33.Remove engine to bell housing fixings, leaving
starter motor attached to engine.
34.Carefully raise engine to release from gearbox.
35.Ensure all relevant connections to engine have
been removed.
36.Remove engine.
Refit
37.Clean bell housing.
38.Apply Hylomar sealant to mating faces of bell
housing and flywheel housing.
39.Lubricate splines of gearbox primary pinion with
Rocol MV 3.
40.Carefully lower engine into position and locate
primary pinion into clutch and engage bell
housing dowels.
41.Fit engine to bell housing fixings. Tighten to
40
Nm (30 lbf/ft).