1996 LAND ROVER DEFENDER air filter

12ENGINE
6
REPAIR 42.Raise engine, and locate front engine mountings
to chassis.
43.Remove gearbox support and lower engine.
44.Tighten front engine mounting to chassis fixings
to
45 Nm (33 lbf/ft).
45.Release chains from engine lifting brackets and
remove hoist.
46.Connect oil cooler pipes to oil filter adaptor.
47.Fit vacuum hose to brake servo adaptor.
48.Secure fuel feed pipe in retaining clip on air
cleaner bracket.
49.Fit fuel lift pump pipes.
50.Connect feed and spill return pipes to injector
pump.
51.If fitted, reconnect hand throttle cable to
mounting bracket and injector pump.
52.Fit outer cable adjusting nut into injector pump
mounting bracket.
53.Fit inner throttle cable to injector pump and
secure with clevis and split pin.
54.Secure bleed hose in retaining clips on front
timing cover.
55.Fit bleed hose to thermostat housing.
56.Connect inlet and outlet hoses to power steering
pump.
57.Fit down pipe to exhaust manifold and secure
with 3 nuts.
58.Connect starter motor battery and fuse box
leads.
59.If fitted, connect EGR valve multi-plug and
vacuum pipe.
60.Secure breather pipe clip to cylinder head.
61.Connect engine harness multi-plug.
62.Fit heater plug feed wire.
63.Connect electrical feed plug at rear of cylinder
head.
64.Fit heater hoses to cylinder head and heater
rails.
65.Fit feed pipe/hose to turbo-charger and
intercooler.
66.Fit rocker cover insulation.
67.Fit radiator assembly.
See COOLING SYSTEM,
Repair, Radiator
If applicable, fit air
conditioning condenser, compressor pipes and
heater matrix hoses.
See AIR CONDITIONING,
Repair, Condenser
68.Fit bonnet.
69.Reconnect battery.CRANKSHAFT PULLEY
Service repair no - 12.21.01
Remove
1.Disconnect battery.
2.Drain coolant.
See COOLING SYSTEM,
Repair, Drain and refill cooling system
3.Remove top hose from radiator.
4.Remove intercooler to induction manifold hose.
5.Remove viscous coupling and fan.
See
COOLING SYSTEM, Repair, Viscous
coupling and fan
6.Remove fan cowl.See COOLING SYSTEM,
Repair, Fan cowl
7.Remove drive belt.See ELECTRICAL, Repair,
Auxiliary drive belt
8.Fit crankshaft pulley retainerLRT-12-080and
secure with 4 bolts.
9.Remove crankshaft pulley retaining bolt
anti-clockwise using socket and suitable long
bar.
10.Remove pulley retainer.
11.Remove pulley, if necessary using extractor
LRT-12-049with thrust pad fromLRT-12-031.

ENGINE
19
REPAIR OIL FILTER
Service repair no - 12.60.01
Remove
1.Place drain tray under oil filter.
2.Unscrew filter anti-clockwise, using a strap
wrench, if necessary.
Refit
3.Clean mating face of oil filter adaptor.
4.Coat rubber sealing ring of new filter with clean
engine oil.
5.Screw on filter until sealing ring touches
machined face, then tighten a further half turn by
hand only. DO NOT over tighten.OIL TEMPERATURE CONTROL VALVE
Service repair no - 12.60.69
Remove
1.Clean adaptor housing.
2.Disconnect oil cooler feed pipe from thermostat
extension housing and plug to prevent ingress of
dirt.
3.Remove 2 bolts and carefully withdraw
thermostat extension housing (1) complete with
'O' ring seal (2), thermostat (3), 2 washers (4)
and spring (5).
4.Inspect all parts and renew as necessary.
Refit
5.Fit thermostat to extension housing ensuring pin
locates in hole.
6.Fit two washers and spring to thermostat.
7.Fit a new 'O' ring to extension housing.
8.Insert spring into adaptor and secure extension
housing to adaptor. Tighten bolts to
9Nm(7
lbf/ft).

12ENGINE
20
REPAIR OIL FILTER HEAD GASKET
Service repair no - 12.60.03
Remove
1.Clean filter head adaptor.
2.Disconnect oil cooler pipes and plug to prevent
ingress of dirt.
3.Disconnect oil pressure switch lead.
4.Remove 4 bolts and withdraw filter head,
complete with gasket.
5.Clean mating faces of filter head and cylinder
block.
6.Fit head with new gasket.
7.Tighten bolts to
45 Nm (33 lbf/ft).
8.Reconnect oil pressure switch lead.
9.Reconnect oil cooler pipes.CYLINDER HEAD GASKET
Service repair no - 12.29.02
Remove
1.Disconnect battery
2.Remove bonnet.
3.Drain coolant.
See COOLING SYSTEM,
Repair, Drain and refill cooling system
4.Remove air cleaner.See FUEL SYSTEM,
Repair, Air cleaner
5.Detach crankcase ventilation valve and side
breather hose from rocker cover and move to
one side.
6.Remove fuel injectors and pipes.
See FUEL
SYSTEM, Repair, Fuel injectors
7.Remove heater plugs.See FUEL SYSTEM,
Repair, Heater plugs
8.Disconnect radiator top hose from thermostat.
9.Disconnect bleed hose at thermostat.
10.Disconnect water pump hose at thermostat.
11.Disconnect water temperature sensor lead.

ENGINE
3
SPECIFICATIONS, TORQUENm
Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Starter motor (bolt and nut) 45........................................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................
Generator to auxiliaries mounting bracket 25.................................................
Tachometer electrical connection 4...............................................................

19FUEL SYSTEM
2
DESCRIPTION AND OPERATION A mechanical lift pump, with a hand priming facility, is
driven by the camshaft, and is mounted on the RH
side of the engine.
A fuel filter, with a replaceable element and
incorporating a water separator, is mounted on the
front RH side of the engine compartment.
A fuel sedimentor may be fitted when the vehicle is
operating in more arduous conditions, and is used to
minimise water deposits in the fuel system before
reaching the fuel pump and filter.
Fuel injection is carried out by a Bosch direct injection
pump, incorporating a cold start advance unit and a
high idle setting. The pump is mounted on the RH side
of the engine and is driven directly by gears in the
front cover from the crankshaft. The pump meters and
distributes fuel to 4 pintle type injectors located in
pre-combustion chambers in the cylinder head. Four
heater plugs, located in the cylinder head directly
below each injector, are fitted to improve cold starting.
An optional hand throttle, for use with a centre power
take off, is located on the fascia to the LH side of the
fuse box, and is linked independently to the fuel
injection pump throttle lever.
Air intake
The air cleaner is mounted on the RH side of the
engine and is connected by hoses to the cold air
intake duct and turbocharger inlet. Fitted between the
air cleaner and turbocharger is the crankcase breather
hose which connects to a breather filter on the rocker
cover.
A single stage turbocharger, fitted between the
exhaust manifold and exhaust down pipe, is
connected by hoses to the air cleaner and an
intercooler which is mounted on the LH side of the
radiator. The intercooler is connected by a hose to the
inlet manifold. When an EGR valve is fitted to the
turbocharger, additional pipes/hoses are used to
connect the components.Exhaust gas recirculation (EGR), when fitted.
Exhaust gas recirculation is controlled by an ECU
mounted under the front centre seat or cubby box and
receives the following inputs:
·Engine temperature from coolant temperature
sender unit on LH side of cylinder head.
·Throttle position from potentiometer on injection
pump.
·Engine speed from speedometer.
When all correct signals are received, the EGR
solenoid allows vacuum to open EGR valve and
recirculate a portion of the exhaust gas. See J6196 for
the EGR system component location and 'Operation'
for full system function.

FUEL SYSTEM
7
DESCRIPTION AND OPERATION
FUEL SYSTEM COMPONENT LOCATION
1.Fuel filter bleed screw
2.Fuel filter
3.Turbocharger
4.Actuator
5.Air cleaner
6.Fuel injector7.Heater plug
8.Heater plug controller
9.Coolant temperature transmitter
10.Fuel injection pump
11.Fuel lift pump
12.Intercooler

FUEL SYSTEM
9
DESCRIPTION AND OPERATION OPERATION
Diesel engines operate by compression ignition. The
rapid compression of air in the cylinder during the
compression cycle heats the air and when fuel is
injected into the heated air, it ignites instantaneously.
During cold tarting, automatically controlled heater
plugs assist in raising the temperature of the
compressed air to ignition point.
A cold start advance unit advances the injection timing
to further assist starting. Idle quality is improved by
the high idle setting.
The engine is supplied with pre-compressed air by a
single stage turbocharger.
Exhaust gases passing over a turbine cause it to
rotate, driving a compressor mounted on the turbine
shaft. Air drawn from the cold air intake passes, via
the air cleaner, to the turbocharger where it is
compressed. Compression in the turbocharger warms
up the air considerably, so that it expands. As a result
the air mass per cylinder is reduced, having a
negative effect on power output. By fitting a charge-air
intercooler, located on the LH side of the radiator, the
air is cooled before reaching the cylinders. This
increases power output through increased mass of
oxygen in the combustion process, as well as
maximising engine durability, through maintaining
lower piston and head temperatures.
Fuel is drawn from the tank by a mechanical lift pump
and passes to the injection pump via a filter. In
addition to removing particle contamination from the
fuel, the filter incorporates a water separator, which
removes and stores water.
The sedimentor/s, when fitted, is located adjacent to
the fuel tank/s and separates contamination and water
particles in the fuel before reaching the fuel lift pump.
The injection pump meters a precisely timed, exact
quantity of fuel to the injectors in response to throttle
variations, injection timing varying with engine speed.
Any excess fuel delivered to the injection pump is
passed back to the tank via the spill return line.
Fuel is injected in a finely atomised form into the main
combustion chamber, the burning fuel expands
rapidly, creating extreme turbulence which mixes the
burning fuel thoroughly with the compressed air,
providing complete combustion.Cold Starting is assisted by heater plugs, a cold start
advance unit and a high idle setting.
Heater plugs
Heater plug operation is controlled by a timer unit,
start relay and resistor. When the ignition is turned on
the timer unit is energised, the heater plugs start to
operate and a warning light on the dashboard
illuminates, remaining on until the heater plugs are
automatically switched off.
The length of time the heater plugs will operate is
dependent on under bonnet temperature, which is
monitored by a sensor located in the timer unit.
Starting the engine results in the power supply to the
heater plugs passing through the resistor, which
reduces their operating temperature. The heater plugs
are cut out either by the temperature sensor in the
timer, or by a microswitch on the injection pump which
operates when the throttle is depressed.
Cold start advance
The cold start advance unit is connected to the engine
cooling system via hoses. It contains a temperature
sensitive element which is retracted when cold and
pulls the advance lever, via cable, towards the rear of
the pump against spring pressure. As coolant
temperature rises, the cold start element expands
releasing tension on the cable and allowing spring
pressure to move the advance lever forwards.
Exhaust gas recirculation (EGR), when fitted
Operation of the EGR system is dependent on the
following:
·Engine temperature - must be between 20°C and
100°C approx.
·Engine speed - must be between 630 and 2850
rev/min.
·Engine load - calculated by throttle position
sensor.
·EGR valve lift position.
·Duration of engine idling.

19FUEL SYSTEM
4
ADJUSTMENT TURBOCHARGER BOOST PRESSURE - CHECK
Service repair no - 19.42.06
1.Disconnect actuator hose from turbocharger and
insert a suitable 'T' piece connector.
2.Connect a short length of suitable hose to
turbocharger and 'T'piece.
3.Connect further hose to 'T' piece and pressure
gaugeLRT-12-011. The pressure gauge hose
must be long enough to reach into the vehicle
cab so that the gauge can be observed by driver
or passenger.
4.To check maximum boost pressure, drive
vehicle normally, but in such a manner that full
throttle can be maintained whilst climbing a hill
with engine speed held steady between 2,500
and 3,000 rev/min. Under these circumstances
boost pressure should read 0,95 - 1,09 Kgf/cm
2
(13.5 - 15.5 lb/in2).PRIMING THE FUEL SYSTEM
Service repair no - 19.50.01
NOTE: If the fuel system has been
completely drained carry out the
procedures for priming both the
sedimentor, if fitted, and fuel filter and injection
pump.
Sedimentor and fuel filter
If the sedimentor or fuel filter have been dismantled
and air has entered the fuel system carry out the
following procedure:
1.Slacken fuel filter bleed screw.
2.Operate hand priming lever on fuel lift pump until
fuel, free from air, emerges from filter.
NOTE: Ensure that the fuel pump lever is
on the bottom of operating cam when
priming, otherwise maximum movement of
the lever cannot be achieved.
3.Tighten filter bleed screw whilst fuel is still
emerging.