1996 LAND ROVER DEFENDER ground clearance

04GENERAL SPECIFICATION DATA
10
INFORMATION TOWING WEIGHTS
On-road Off-road
Unbraked trailers 750 Kg (1653 lb).............................................................. 500 Kg (1102 lb)
Trailers with overrun brakes 3500 Kg (7716 lb)............................................. 1000 Kg (2204 lb)
4 wheel trailers with coupled brakes * 4000 Kg (8818 lb).............................. 1000 Kg (2204 lb)
NOTE: * Only applies to vehicles modified to accept coupled brakes.
NOTE: All weight figures are subject to local restrictions.
OFF-ROAD PERFORMANCE
90 models
Max. gradient (EEC kerb weight) 45° .....................................
Approach angle:
Soft top and Pick-up (EEC kerb weight) 48° ..................
Hard top and station wagon (EEC kerb weight) 51.5° ......
Departure angle
Soft top and Pick-up (EEC kerb weight) 49° ..................
Hard top and Station wagon (EEC kerb weight) 53° ...............
Wading depth 500 mm (20 in)...................................................................
Min. ground clearance (unladen):
Soft top and pick-up 191 mm (7.5 in).................................................
Hard top and station wagon 229 mm (9.0 in).....................................
NOTE: Departure angles do not account for the addition of a tow hitch.
110 and 130 models
Max. gradient (EEC kerb weight) 45° .....................................
Approach angle (EEC kerb weight) 50° ..................................
Departure angle (EEC kerb weight)
110 models 35° ......................................................................
130 models 34° ......................................................................
Wading depth 500 mm (20 in)...................................................................
Min. ground clearance (unladen 215 mm (8.5 in).......................................
NOTE: Departure angles do not account for the addition of a tow hitch.

MAINTENANCE
1
MAINTENANCE SERVICE SCHEDULE
The following section describes the items detailed in
the vehicle Service Schedule. Where required
instructions are given for carrying out the service
procedure, or a cross reference is given to the section
in the manual where the procedure may be found.
Service Maintenance Schedules are published
separately to reflect the needs and intervals for each
vehicle variant. Procedures in the Workshop Manual
must be used in conjunction with the Service
Schedule sheets.
Service Maintenance Schedules are available from:
Land Rover Publications,
Character Mailing,
Heysham Road,
Bootle,
Merseyside, L70 1JL
VEHICLE INTERIOR
CHECK SEATS & BELTS
Check condition and security of seat belts, seat belt
mountings, seat belt buckles and operation of inertia
seat belts.
CHECK OPERATION OF LAMPS
Check operation of all lamps, horns and warning
indicators.
CHECK OPERATION OF WIPERS
Check operation of front/rear wipers and washers and
condition of wiper blades.CHECK OPERATION OF HANDBRAKE
Handbrake check/adjust
1.Chock road wheels.
2.Raise one rear wheel clear of ground and
support securely with axle stand.
3.Release handbrake lever.
4.Underneath vehicle, tighten adjuster bolt
clockwise to
25 Nm (18 lbf/ft)to fully lock brake
drum.
5.Slacken adjusting bolt by 1.5 turns to give brake
shoes running clearance. Check that the drum is
free to rotate.
6.Adjust handbrake cable locknuts to give pawl
two notches free movement on the rachet before
being fully operational on third notch of rachet.
NOTE: Cable adjustment must ONLY be
used for initial setting and to compensate
for cable stretch. It MUST NOT be used to
take up brake shoe wear, which MUST be adjusted
at brake drum.
7.Operate handbrake to settle brake shoes.
Recheck handbrake is fully operational on third
notch of rachet pawl. Readjust if necessary.
8.Remove axle stand and wheel chocks.

FRONT SUSPENSION
1
DESCRIPTION AND OPERATION DESCRIPTION
The front suspension design allows maximum wheel
travel and axle articulation providing good ground
clearance without loss of traction or directional
stability.
Long radius arms are fitted to the front axle and
provide maximum axle articulation which is vital for off
road performance. The radius arms are secured to
fabricated mounting brackets welded to the front axle.
Flexible rubber bushes are used on a stem end joint
to secure the rear of the radius arms to mountings on
the chassis cross member.
A panhard rod, which ensures that the front axle
remains centrally located, is fitted transversely and
also uses ferrule rubber bush mountings at both axle
and chassis locations.Two rubber bearing bushes, with retaining straps,
secure the rear of the anti-roll bar to the chassis
mountings, while bushed links support the front of the
bar to the front axle.
Conventional long travel coil springs and hydraulic
shock absorbers are used to control body movement
in all conditions. The shock absorbers are secured to
fabricated towers which are bolted to the chassis. The
upper and lower fixings use a single location stud with
flexible rubber bushes, support washers and securing
nuts. Retaining plates are used to secure the coil
springs to the fabricated towers and axle mountings.
Rubber bump stops are fitted underneath the chassis,
adjacent to the front road springs, and prevent
possible damage that could occur should there be
excessive axle to chassis movement.
Front suspension
1.Panhard rod
2.Radius arms
3.Coil springs
4.Shock absorber
5.Anti-roll bar

70BRAKES
16
REPAIRREV: 05/99 TRANSMISSION BRAKE SHOES
Service repair no - 70.45.18
Remove
1.Park vehicle on level ground, chock road wheels
and release handbrake. Alternatively, raise
vehicle on a ramp.
2.Disconnect rear propeller shaft from
transmission output flange at brake drum.
3.Slacken off transmission brake drum adjustment
bolt.
4.Remove single screw securing brake drum to
output flange.
5.Withdraw drum to expose brake assembly.
6.Release top and bottom springs from brake
shoes, see J6337.
7.Grip dished washer with a pair of pliers, depress
washer and turn through 90°.
8.Remove dished washer, complete with hold
down spring and pin from both shoes.
9.Move brake shoes out from adjuster slides,
release from abutment plate and remove from
backplate.
10.Check that springs are satisfactory for continued
use. If new brake shoes are to be fitted, the
srings should also be renewed.Refit
11.Locate RH brake shoe in slide and secure brake
shoe and lever assembly to backplate with hold
down pin, spring and dished washer.
12.Locate LH brake shoe in slide and fit abutment
plate between both brake shoes. Secure LH
shoe with hold down pin, spring and dished
washer.
13.Fit pull-off springs to brake shoes.
14.Fit brake drum. Tighten screw to
25 Nm (18
lbf/ft).
15.Check that hand brake lever is released.
16.Screw in and tighten adjuster bolt until brake
drum will not rotate by hand.
17.Tighten adjuster bolt to
25 Nm (18 lbf/ft)to
ensure brake drum is locked.
18.Slacken off adjuster bolt by 1.5 turns to give
shoes a running clearance. Check that the drum
is free to rotate.
19.Fit propeller shaft to output flange. Tighten
fixings to
46 Nm (34 lbf/ft).
20.Remove wheel chocks and check operation of
handbrake.

BRAKES
17
REPAIR HANDBRAKE CABLE
Service repair no - 70.35.25
Remove
1.Park vehicle on level ground, chock road wheels
and release handbrake. Alternatively, raise
vehicle on ramp.
2.Remove 3 trim studs and lift up handbrake
gaiter.
3.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever.
4.Slacken off transmission brake drum adjusting
screw.
5.Disconnect propeller shaft from output flange.
6.Remove retaining screw and withdraw brake
drum.
7.Release handbrake cable clevis from abutment
on cable lever, see J6337, and pull through
aperture in back plate.
8.Pull cable from heelboard and remove from
vehicle.
Refit
9.Feed new cable through heelboard ensuring
rubber grommet is correctly located.
10.Position cable over guide plate, insert through
backplate and connect to cable lever.
11.Fit cable to handbrake lever and secure with
clevis pin and split pin.
12.Fit handbrake gaiter.
13.Fit brake drum. Tighten screw to
25 Nm (18
lbf/ft).
14.Screw in and tighten adjuster bolt until brake
drum will not rotate by hand.
15.Tighten adjuster bolt further to
25 Nm (18 lbf/ft)
to ensure brake drum is locked.
16.Slacken off adjuster bolt by 1.5 turns to give
brake shoes running clearance. Check that the
drum is free to rotate.
17.Slacken locknut and adjust cable to give the
handbrake pawl two notches free movement on
the rachet before being fully operational on third
notch (brake shoes are fully expanded against
drum).
NOTE: Cable adjustment is for a new cable
or to compensate for cable stretch. Cable
adjustment must not be used to take up
brake shoe wear.
18.Fit propeller shaft to output flange. Tighten
fixings to
46 Nm (34 lbf/ft).
19.Remove wheel chocks and check operation of
handbrake.