1996 LAND ROVER DEFENDER oil level

GENERAL SPECIFICATION DATA
5
INFORMATION SUSPENSION
Type Coil springs controlled by telescopic dampers front.................................................................................
and rear.
Front Transverse location of axle by Panhard rod, and fore.................................................................................
and aft location by two radius arms. Anti-roll bar fitted
as standard on 90 models with 265/75 tyres and 130
models.
Rear Fore and aft movement inhibited by two tubular trailing.................................................................................
links. Lateral location of axle by a centrally positioned
'A' frame, upperlink assembly, bolted at the apex to a
ball joint mounting. Anti-roll bar fitted as standard on
90 models with 265/75 tyres, 110 models with self
levelling unit, and 130 models.
ROAD SPRING DATA
90 (2400 Kg) Part No. Colour Code
Front - Driver's side NRC 9446 Blue/green
Front - Passenger side NRC 9447 Blue/yellow
Rear - Driver's side NRC 9448 Blue/red
Rear - Passenger side NRC 9449 Yellow/white
90 (2550 Kg)
Front - Driver's side NRC 9446 Blue/green
Front - passenger side NRC 9447 Blue/yellow
Rear - Driver's side NRC 9462 Green/yellow/red
Rear - Passenger side NRC 9463 Green/yellow/white
110 (3050 Kg)
Front - both sides NRC 8045 Yellow/yellow
Rear - both sides NRC 6904 Red/green
110 Levelled (2950 Kg)
Front - both sides NRC 8045 Yellow/yellow
Rear - both sides NRC 7000 Green/white
110 (3400 Kg)
Front - both sides NRC 8045 Yellow/yellow
Rear - both sides NRC 6904 Red/green
Rear helper springs - both sides RRC 3266 No colour code
110 (3600 Kg)
Front - Driver's side NRC 9448 Blue/red
Front - passenger side NRC 9449 Yellow/white
Rear - both sides NRC 6904 Red/green
Rear helper springs - both sides RRC 3226 No colour code
130 (3500 Kg)
Front - driver's side NRC 9448 Blue/red
Front - passenger side NRC 9449 Yellow/white
Rear - driver's side NRC 6389 Red/red
Rear - passenger side NRC 6904 Red/green
Front/rear helper springs - both sides RRC 3266 No colour code

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION REV: 05/99 CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Pints
Engine sump oil 5,8................................................................ 10.20
Extra when refilling after fitting new filter 0,85.......................... 1.50
Manual gearbox 2,67............................................................... 4.70
Transfer gearbox oil 2,30......................................................... 4.00
Front differential 1,70............................................................... 3.00
Rear differential 1,70................................................................ 3.00
Power steering box and reservoir LHD 2,90............................ 5.00
Power steering box and reservoir RHD 3,40............................ 6.00
Swivel pin housing oil/grease (each) 0,35................................ 0.60
Fuel tank usable fuel 79,5........................................................ 17.5 gall
Cooling system 11,50................................................................ 20.20
Washer bottle 3,0................................................................... 5.28
NOTE: * All levels must be checked by dipstick or level plugs as applicable.
ANTI-FREEZE
PERCENTAGE CONCENTRATION - 50%
PROTECTION - LOWER TEMPERATURE LIMIT
Complete protection
Vehicle may be driven away immediately from cold,
-33°C (-36°F).
Safe limit protection
Coolant in semi-frozen state. Engine may be started
and driven away after warm-up period, -41°C (-42°
F).Lower protection
Prevents frost damage to cylinder head, block and
radiator. Thaw out before starting engine, -47°C (-53°
F).
CAUTION: Anti-freeze content must never
be allowed to fall below 25% (pre 99MY) or
50% (99MY on) otherwise damage to the
engine is liable to occur. Anti-freeze content
should not exceed 60% (all models) as this will
greatly reduce cooling efficiency.

MAINTENANCE
3
MAINTENANCE UNDER BONNET MAINTENANCE
UNDER BONNET COMPONENTS
A - RH drive
1.Brake fluid reservoir
2.Clutch fluid reservoir
3.Air cleaner element
4.Engine breather filter
5.Oil filler cap
6.Oil level dipstick
7.Heater/air conditioning unit
8.Windscreen washer reservoir
9.Power steering pump reservoir10.Intercooler and hoses
11.Radiator filler plug
12.Radiator
13.Oil cooler
14.Fuel filter
15.Accelerator linkage
16.Expansion tank
17.Air cleaner dump valve

10MAINTENANCE
4
MAINTENANCE
UNDER BONNET COMPONENTS
B - LH drive
1.Brake fluid reservoir
2.Clutch fluid reservoir
3.Air cleaner element
4.Engine breather filter
5.Oil filler cap
6.Oil level dipstick
7.Heater/air conditioning unit
8.Windscreen washer reservoir
9.Power steering pump reservoir10.Intercooler and hoses
11.Radiator filler plug
12.Radiator
13.Oil cooler
14.Fuel filter
15.Accelerator linkage
16.Expansion tank
17.Air cleaner dump valve

MAINTENANCE
9
MAINTENANCE REV: 05/99 UNDER VEHICLE MAINTENANCE
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
maintenance, or remove and refit procedures are
required, it may be necessary to remove the
undertray and/or integral access panels
See
CHASSIS AND BODY, Repair, Front undertray
or
See CHASSIS AND BODY, Repair, Rear undertray
RENEW ENGINE OIL AND FILTER
1.Ensure vehicle is level.
2.Run engine to warm oil, switch off ignition.
3.Disconnect battery.
4.Place suitable drain tray under sump drain plug.
5.Remove drain plug from sump and allow oil to
drain completely.
6.Fit new sealing washer, replace plug and tighten
to
35 Nm (26 lbf/ft).
7.Place drain tray under oil filter.
8.Unscrew filter anti-clockwise, using a strap
wrench if necessary.
9.Clean mating face of oil filter adaptor.
10.Coat rubber sealing washer of new filter with
clean engine oil.
11.Screw filter on clockwise until sealing washer
touches adaptor mating face, tighten a further
half turn by hand only. DO NOT overtighten.
12.Clean and remove filler cap from rocker cover.
13.Pour in correct quantity and grade of new oil
from a sealed container.
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
14.Check that oil level is between upper and lower
marks on dipstick. DO NOT fill above upper
mark.
15.Firmly replace filler cap.
16.Reconnect battery, run engine and check oil filter
for leaks.
17.Stop engine, allow oil to run back into sump for a
few minutes and check oil level again. Top up if
necessary.

10MAINTENANCE
10
MAINTENANCEREV: 05/99 RENEW GEARBOX OIL
1.Ensure vehicle is level.
2.Place suitable tray under gearbox.
3.Disconnect battery.
4.Clean area around filler/level plugs.
5.Remove both plugs and allow oil to drain
completely.
WARNING: When draining gearbox, care
should be taken to ensure that oil is not
hot as personal scalding could result.
6.Refit drain plug and tighten to
30 Nm (22 lbf/ft).
7.Inject new oil into gearbox until it runs out of filler
hole. Allow excess oil to drain and wipe clean.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
lubricants and fluids
8.Refit filler/level plug and tighten to30 Nm (22
lbf/ft).
9.Reconnect battery.
RENEW TRANSFER GEARBOX OIL
1.Ensure vehicle is level.
2.Disconnect battery.
3.Clean area around filler/level and drain plugs.
WARNING: When draining gearbox care
should be taken to ensure that oil is not
hot as personal scalding could result.
4.Place suitable tray under transfer gearbox.
5.Remove filler/level plug to vent gearbox and
assist draining.
6.Remove drain plug and allow oil to drain.
7.Thoroughly clean drain plug threads and apply
fresh 'Hylomar' sealant.
8.Refit drain plug and tighten to
30 Nm (22lbf/ft).
9.Inject new oil of correct quantity and grade into
gearbox until oil runs out from filler/level hole.
Allow excess oil to drain and wipe clean.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
10.Thoroughly clean filler/level plug and apply fresh
'Hylomar' sealant.
11.Refit plug and tighten to
30 Nm (22 lbf/ft).
12.Reconnect battery.
CHECK/TOP UP TRANSFER GEARBOX OIL
1.Ensure vehicle is level.
2.Disconnect battery.
3.Clean area around filler/level plug.
4.Remove plug, check oil level and top up if
necessary with correct grade of oil,
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
until oil runs out from filler/level hole.
Allow excess oil to drain and wipe clean.
5.Thoroughly clean filler/level plug threads and
apply fresh 'Hylomar' sealant.
6.Refit plug and tighten to
30 Nm (22 lbf/ft).
7.Reconnect battery.

MAINTENANCE
11
MAINTENANCE REV: 05/99 RENEW FRONT AND REAR AXLE OIL
1.Ensure vehicle is level and place suitable tray
under axle to be drained.
2.Using 13mm square drive wrench, remove drain
and filler/level plugs from axle and allow oil to
drain completely.
3.Clean and refit drain plug.
A- Front and rear axle, 90 models, front, 110/130
models.B- Rear axle, 110/130 models.
4.Inject new oil,
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended lubricants and fluids
until it
runs out from filler/level hole. Allow excess oil to
drain and wipe clean.
5.Clean and refit filler/level plug.
CHECK/TOP UP FRONT AND REAR AXLE
1.Ensure vehicle is level.
2.Using 13 mm square drive wrench, remove
filler/level plug.3.If necessary inject new oil until oil runs out from
filler/level hole. Allow excess oil to drain and
wipe clean.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
lubricants and fluids
4.Clean and refit filler/level plug.
RENEW SWIVEL PIN HOUSING OIL
1.Ensure vehicle is level and place suitable tray
under swivel to be drained.
2.Remove drain and level plugs, allow oil to drain
completely. Clean and refit drain plug.
3.Remove filler plug and inject new oil until oil runs
out from level hole.
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
Allow
excess oil to drain and wipe clean.
4.Clean and refit filler and level plugs.
NOTE: On later vehicles, the level and
drain plugs have been deleted. The swivel
pin housing is filled with grease on
manufacture, for life service, and maintenance is
not required.
CHECK/TOP UP SWIVEL PIN HOUSING OIL
1.Ensure vehicle is level.
2.Remove level and filler plug, check oil level and
top up if necessary with new oil until oil runs out
from level hole. Allow excess oil to drain and
wipe clean.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
lubricants and fluids
3.Clean and refit filler and level plugs.

10MAINTENANCE
14
MAINTENANCEREV: 05/99 ADDITIONAL MAINTENANCE SCHEDULES
Camshaft drive belt
The engine timing gears are driven by a toothed
rubber belt which must be renewed at intervals
determined by the severity of operating conditions. In
reasonable, temperate climate operation, the belt
should be renewed every 120,000 km (72,000 miles)
or every six years whichever occurs earlier.
In adverse operating conditions, such as work in dusty
atmospheres, high ambient temperatures, desert and
tropical zones, renew the belt every 60,000 km
(36,000 miles) or every three years, whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious engine damage.
Oil change diesel engines
If the vehicle is operated on fuel with a high sulphur
content (over 1%) the oil change intervals must not
exceed 5000 km (3000 miles).
Anti-freeze
At two yearly intervals or at the onset of the second
winter, the cooling system should be drained, flushed
and refilled with the required water and anti-freeze
solution.
Hydraulic brake fluid.
It is recommended that at 40,000 km (24,000 miles)
intervals or every two years, whichever is the earlier,
the hydraulic brake fluid should be completely
renewed.
At 80,000 km (48,000 miles) intervals or every four
years, whichever is the earlier, all hydraulic brake fluid
seals and flexible hoses should be renewed. All
working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.Air cleaner
When the vehicle is used in dusty or field conditions or
deep wading, frequent attention to the air cleaner may
be required.
Dampers
At 60,000 km (36,000 miles) intervals remove all
suspension dampers, test for correct operation, refit or
renew as necessary.
SPECIAL OPERATING CONDITIONS
When the vehicle is operated in extremely arduous
conditions or on dusty, wet or muddy terrain, more
frequent attention should be paid to all servicing
requirements.
Additional daily or weekly attention depending on
operating conditions:
Check/top-up transfer box oil.
Check steering rubber boots for security and
condition. Renew if damaged.
Check brake fluid level: Investigate cause if any fluid
loss is suspected.
Clean brake discs and calipers.
Lubricate front and rear propeller shaft
universal/sliding joints. Under tropical or severe
conditions, particularly where sand is encountered,
the sliding joints must be lubricated very frequently to
prevent ingress of abrasive material.
Every week and every maintenance inspection check
tyre pressures and inspect tyre treads and side walls.
Under arduous cross-country conditions the tyre
pressures should be checked much more frequently,
even to the extent of a daily check.
Monthly
Renew gearbox oil.
Renew transfer box oil.
Check air cleaner element and renew every 6 months
or as necessary.