1996 LAND ROVER DEFENDER width

04GENERAL SPECIFICATION DATA
6
INFORMATION SHOCK ABSORBERS
Type Telescopic, double-acting non-adjustable.................................................................................
Bore diameter 35.47mm...................................................................
BRAKES
Front service brake
Caliper AP Lockheed, four opposed pistons..............................................................................
Operation Hydraulic, self adjusting.........................................................................
Disc 90 - Solid, outboard, 110/130 - Ventilated, outboard..................................................................................
Disc diameter 298 mm (11.73 in)...................................................................
Disc thickness 90 - 14,1 mm (0.56in), 110/130 - 24mm (0.95 in)..................................................................
Wear limit 1 mm (0.04in) per side of disc.........................................................................
Disc run-out maximum 0,15mm (0.006 in).....................................................
Pad area 58 cm
2(9.0 in2) ..........................................................................
Total swept area 801,3 cm2(124.2 in2) ...............................................................
Pad material Ferodo 3440 non asbestos.....................................................................
Pad minimum thickness 3 mm (0.12in)...................................................
Rear service brake
Caliper AP Lockheed opposed piston..............................................................................
Operation Hydraulic, self adjusting.........................................................................
Disc Solid, outboard..................................................................................
Disc diameter 90 - 290 mm (11.42 in), 110/130 - 298 mm (11.73)...................................................................
Disc thickness 90 - 12,5 mm (0.49 in), 110/130 - 14,1 mm (0.56 in)..................................................................
Wear limit 90 - 0,38 mm (0.015 in), 110/130 - 1,0 mm (0.04 in).........................................................................
per side of disc
Disc run-out maximum 0,15 mm (0.006 in).....................................................
Pad area 90 - 30,5 cm
2(4.37 in2), 110/130 - 36,2 cm2(5.61 in2) ..........................................................................
Total swept area 90 - 694 cm2(106.98 in2) ...............................................................
Pad material Ferodo 3440 non asbestos.....................................................................
Pad minimum thickness 3 mm (0.12 in)...................................................
Parking brake
Type Mechanical, cable operated drum brake on the rear of.................................................................................
the transfer gearbox output shaft
Drum internal diameter 254 mm (10.0 in).....................................................
Width 70 mm (2.75 in)................................................................................
Pad material Ferodo 3611 non asbestos.....................................................................
Servo/master cylinder
Manufacturer Lucas....................................................................
Servo type LSC 80........................................................................
Master cylinder type 25,4 mm (1.0 in) diameter, tandem.........................................................
Pressure reducing valve, failure conscious Cut-in pressure, 90 - 24 bar (360 Ibf/in
2) ratio 4.0:1, ......................
110 - 43 bar (645 Ibf/in2) ratio 2.9:1*
NOTE: * Pressure reducing valves are not fitted to all 110 specifications.

04GENERAL SPECIFICATION DATA
12
INFORMATION VEHICLE DIMENSIONS
90 models
Overall length:
Soft top and Pick-up 3722 mm (146.5 in)................................................
Hard top and Station wagon 3883 mm (152.9 in)....................................
Overall width: 1790 mm (70.5 in)...................................................................
Overall height:
Soft top 1965 mm (77.4 in)....................................................................
Pick-up and Station wagon 1963 mm (77.3 in)......................................
Hard top 1972 mm (77.6 in)...................................................................
Wheelbase 2360 mm (92.9 in).......................................................................
Track front/rear 1486 mm (58.5 in).................................................................
Width between wheel boxes 925 mm (36.4 in)............................................
110 models
Overall length:
Soft top and Pick-up 4438 mm (175 in)................................................
High capacity pick-up 4631 mm (182 in)..............................................
Hard top/Station and County 4599 mm (181 in)...................................
Overall width: 1790 mm (70.5 in)...................................................................
Overall height: 2035 mm (80.1 in)..................................................................
Wheelbase 2794 mm (110 in).......................................................................
Track front/rear 1486 mm (58.5 in).................................................................
Width between wheel boxes:
High capacity pick-up 1090 mm (43 in)..............................................
all other models 925 mm (36.4 in).......................................................
130 models
Overall length 5132 mm (202 in)...................................................................
Overall width 1790 mm (70.5 in)....................................................................
Overall height 2035 mm (80.1 in)...................................................................
Wheelbase 3226 mm (127 in).......................................................................
Track front/rear 1486 mm (58.5 in).................................................................
Width between wheel boxes 1090 mm (43 in)............................................

WHEELS AND TYRES
1
REPAIR REV: 05/99 GENERAL INFORMATION
WARNING: This is a multi-purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels. The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim
See
Tyre Fitting
.
WARNING: DO NOT fit an inner tube to an
alloy wheel.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment,
See Fault
diagnosis, Tyre Wear Chart
, if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration above.
When the tread has worn to a depth of 1.6 mm the
indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration above.