1996 LAND ROVER DEFENDER ECU

57STEERING
12
REPAIR STEERING DAMPER
Service repair no - 57.55.21
Remove
1.Park vehicle on level ground and chock rear
wheels.
2.Raise vehicle and locate axle stands or use a
ramp.
3.Remove bolt securing steering damper to drag
link bracket.
4.Remove retaining nuts, washers and rubber
bush securing damper to chassis mounting.
5.Withdraw damper.
6.Check rubber bushes and washers, renew if
necessary.Refit
7.Ensuring rubber bushes and washers are
correctly positioned, fit steering damper to
chassis mounting.
8.Fit damper to drag link bracket.
9.Remove axle stands or vehicle from ramp.

STEERING
13
REPAIR REV: 05/99 TRACK ROD AND LINKAGE
Service repair no - 57.55.09
Remove
1.Park vehicle on level ground and chock rear
wheels.
2.Raise vehicle and locate axle stands or use a
ramp.
3.Centralise steering
See Adjustment,
Centralise steering box
.
4.Unscrew 2 bolts and remove track rod protection
bracket from axle differential housing.
5.Remove split pin and castellated nut securing
track rod to swivel housing arms.
6.Disconnect track rod ball joints using
LRT-57-018.
7.Remove track rod.
8.Slacken clamp bolts.
9.Unscrew ball joints.

STEERING
15
REPAIR REV: 05/99 DRAG LINK AND DRAG LINK ENDS
Service repair no - 57.55.17
Remove
1.Park vehicle on level ground and chock rear
wheels.
2.Set road wheels in straight ahead position.
3.Raise vehicle and fit axle stands or use a ramp.4.Remove front road wheel.
5.Disconnect steering damper at drag link bracket.
6.Remove split pin and castellated nut securing
drag link ball joint to swivel housing arm.
7.Disconnect drag link ball joints using
LRT-57-018.
8.Remove drag link.
9.Slacken clamp bolts.
10.Unscrew ball joints and remove from drag link.
11.Clean internal threads of drag link.
12.Fit new ends to drag link and loosely fit clamp
bolts.
13.Set ball joints to drag link measurement to 28,5
mm.
14.Adjust ball pin centres to nominal length of 924
mm, this length is adjusted during refit.

STEERING
1
OVERHAUL POWER STEERING BOX - ADWEST
Service repair no - 57.10.07
Overhaul
NOTE: Overhaul of steering box should
not be carried out during the warranty
period.
WARNING: Wear safety glasses while
removing and refitting circlips and
retaining ring.
CAUTION: Absolute cleanliness is
essential when overhauling power steering
box.
1.Remove steering box from vehicleSee Repair,
Power Steering Box
. Mark drop arm and
steering box for realignment on assembly.
Remove drop arm using extractorLRT-57-012.
Loosen drop arm securing nut, but do not
remove before using extractor. Remove dirt
excluder from output shaft.
2.Drain oil, remove blanking plugs and bleed
screw. Hold steering box over suitable container,
turn input shaft from lock to lock, until oil is
drained. Refit bleed screw.
3.Rotate retainer ring until one end is 12 mm from
extractor hole. Using a drift through hole in
cylinder, lift retaining ring from groove in cylinder
bore.
4.Remove retainer ring, using a screwdriver.
5.Turn input shaft (left lock on left hand drive, right
lock on right hand drive) until piston pushes out
cover. Turn input shaft fully in opposite direction,
applying pressure to piston.
6.Remove set screw retaining rack pad adjuster.
7.Remove rack adjuster and pad.
8.Remove sector shaft adjuster locknut.
9.Remove four bolts from sector shaft cover.
10.Screw in sector shaft adjuster until cover is
removed.
NOTE: Sealant is applied to hexagon
socket to 'tamperproof' sector shaft
adjuster.
11.Slide out sector shaft.

STEERING
9
OVERHAUL Input shaft oil seal
92.Fit seal, lip side first, into housing. Use seal
saverLRT-57-016and seal installer
LRT-57-026. Note that seal is fitted to a depth of
4.75 - 5.00 mm from face of box.
93.Secure seal with circlip.
94.Smear inner lip of dirt excluder with PTFE
grease. Fit dirt excluder usingLRT-57-027.
When fitted correctly outer shoulder of excluder
is 4.00 - 4.50 mm from face of box, dimension X.
95.Remove drop arm. Smear inner lip of dirt
excluder with PTFE grease and refit, ensuring
outer lip is flush with casing.
96.With input shaft on centre, align assembly marks
on drop arm and steering box. Fit drop arm to
steering box using a new tab washer. Tighten to
176 Nm (130 lbf/ft),bend over tab.
97.Fit steering box
See Repair, Power Steering
Box
.

FRONT SUSPENSION
1
DESCRIPTION AND OPERATION DESCRIPTION
The front suspension design allows maximum wheel
travel and axle articulation providing good ground
clearance without loss of traction or directional
stability.
Long radius arms are fitted to the front axle and
provide maximum axle articulation which is vital for off
road performance. The radius arms are secured to
fabricated mounting brackets welded to the front axle.
Flexible rubber bushes are used on a stem end joint
to secure the rear of the radius arms to mountings on
the chassis cross member.
A panhard rod, which ensures that the front axle
remains centrally located, is fitted transversely and
also uses ferrule rubber bush mountings at both axle
and chassis locations.Two rubber bearing bushes, with retaining straps,
secure the rear of the anti-roll bar to the chassis
mountings, while bushed links support the front of the
bar to the front axle.
Conventional long travel coil springs and hydraulic
shock absorbers are used to control body movement
in all conditions. The shock absorbers are secured to
fabricated towers which are bolted to the chassis. The
upper and lower fixings use a single location stud with
flexible rubber bushes, support washers and securing
nuts. Retaining plates are used to secure the coil
springs to the fabricated towers and axle mountings.
Rubber bump stops are fitted underneath the chassis,
adjacent to the front road springs, and prevent
possible damage that could occur should there be
excessive axle to chassis movement.
Front suspension
1.Panhard rod
2.Radius arms
3.Coil springs
4.Shock absorber
5.Anti-roll bar

FRONT SUSPENSION
3
REPAIR REV: 05/99 Refit
11.Assemble shock absorber components.
12.Position shock absorber, complete with bracket
and secure with 4 fixings.
13.Secure shock absorber lower fixing.
14.Fit road wheel, remove chassis stands and jack.
Tighten wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
FRONT ROAD SPRING
Service repair no - 60.20.11.
Remove
1.Remove front shock absorber
See Front
shock absorber
.
CAUTION: Avoid over stretching brake
hoses. If necessary, loosen hose
connector locknuts to allow hoses to
follow axle.
2.Lower axle sufficient to free road spring.
3.Withdraw road spring.
4.Withdraw shock absorber bracket securing ring.
Refit
5.Fit shock absorber bracket retaining ring. Retain
in position with a nut.
6.Position road spring and raise axle.
7.Remove nut retaining securing ring.
8.Fit front shock absorber
See Front shock
absorber
.

60FRONT SUSPENSION
4
REPAIR BUMP STOP
Service repair no - 60.30.10.
Remove
1.Remove fixings.
2.Remove bump stop.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
Refit
3.Position bolts in slots in chassis brackets.
4.Fit bump stop, secure with washers and nuts.ANTI-ROLL BAR
Service repair no - 60.10.01
Remove
1.Mark for reassembly position of rubber bushes
on anti-roll bar.
2.Remove 4 nuts, bolts and washers securing both
anti-roll bar bush straps to chassis mounting
brackets.
3.Remove nuts, bolts, washers and rubber bushes
securing anti-roll bar to both links
4.Remove anti-roll bar.
Refit
5.Position bushes on anti-roll bar. Ensure split
points towards axle on RH bush and away from
axle on LH bush.
6.Fit anti-roll bar with two straps. To ensure correct
fit angled sides of bar should point down.
Loosely fit the bolts, washers and nyloc nuts.
7.Fit bolt, washers and rubber bushes. Using new
nuts fit anti-roll bar to links and tighten to
68Nm
(50 lbf/ft).
8.Tighten nuts securing straps to30Nm (22lbf/ft).