1995 RENAULT MEGANE SCENIC automatic transmission

Strainer mounting bolts 0.5
Sump mounting bolts1
Mounting bolts for engine mounting
dampers on side member2
Rear support mounting bolts6.5
Wheel bolts9
Strainer mounting bolts0.5
Distributor mounting bolts0.5
AUTOMATIC TRANSMISSION
Hydraulic Distributor
23
REMOVAL
Put the vehicle on a 2 post lift.
Put the lever in the "P" (Park) position.
Drain the automatic transmission (mechanismsec-
tion;
drain plug with triangular socket).
Remove:
- the expansion bottle,
- the air filter,
- the two upper bolts (A) of the engine moun-
ting damper and slacken the other two (B), wi-
thout removing them.
TIGHTENING TORQUES (In daN.m)For versions with ABS
Remove the mounting nut (C) from the ABS
electro-pump assembly on the rubber mounting.
Remove the front left hand wheel and remove the
plastic shield from the wheel arch (in order to be
able to remove the two rear mounting bolts of
the automatic transmission sump at a later stage).
Using the component jack, raise the automatic
transmission.
94933-1R
94933R
94887S
23-9

AUTOMATIC TRANSMISSION
Hydraulic Distributor
23
Remove:
- the sump from the automatic transmission,
- the strainer and its seal (bolt 1),
92084R
- the gear control cable from the selector (2) so
that the lever can be moved past the "Park" po-
sition.
99586R
This extra travel is required to release the drive
from the control sector of the manual valve.
94841R
Disconnect the sealed connector cable by pressing
on the locking ring.
94925S
23-10

AUTOMATIC TRANSMISSION
Hydraulic Distributor
23
Remove the sealed connector after having remo-
ved the bolt (3).
94848-1R
Remove the manual valve selector (4) by firstly re-
leasing at (A) and then at (B).
Extract the manual valve from the hydraulic distri-
butor.
94848R
Remove the 16 mounting bolts from the hydraulic
distributor. The bolts marked (*) remain in place
and secure the distributor closing plate.
94841-1R2
Push the gear control selector in fully and release
the hydraulic distributor by releasing the modula-
ting solenoid valve from the sump (5).
91724R
23-11

AUTOMATIC TRANSMISSION
Hydraulic Distributor
23
Ensure that the inserts (6) and the filter (7) have
stayed in position in the sump’s hydraulic circuit.
94852R2
REFITTING
Ensure that the supply tube F1 (8), the modulating
solenoid valve filter (7), and the circuit inserts (6)
are in place.
94852R1
Engage the hydraulic distributor.
Push the gear control selector in fully taking care
to engage the modulating solenoid valve into the
sump (5) correctly.
91724R
Replace the 16 bolts for mounting the distributor
onto the sump and tighten them to a torque of
0.5 daN.m. in accordance with the order shown.
94841-1R1
23-12

AUTOMATIC TRANSMISSION
Hydraulic Distributor
23
Refit the manual valve and the selector (4) by en-
gaging firstly part (A) and then part (B).
91350R4
Refit the sealed connector fitted with its O-ring
and bolt (3).
94848-1R
Fit a new strainer and new seal.
Tighten to a torque of 0.5 daN.m.
94840R
Replace the sump (Ensure that the seals are not
damaged and check that the magnet is present).
Tighten the bolts to a torque of 1
daN.m.
Refit the automatic transmission.
Replace the bolts of the transmission mounting
dampers.
94933-1S
Reconnect the sealed connector.
Refit the gear selector.
23-13

AUTOMATIC TRANSMISSION
Hydraulic Distributor
23
On versions with ABS
Refit the mounting nut
(C) from the ABS electro-
pump unit on the rubber mounting.
94933R
Refit:
- the plastic shield in the front left wheel arch,
- the front left hand wheel,
- the air filter,
- the expansion bottle.
Fill with oil and check the level.
NOTE :every time the hydraulic distributor is re-
placed or removed, replace the modulating sole-
noid valve filter, the strainer and its seal.
23-14

SPECIAL TOOLING REQUIRED
Mot. 1040-01Dummy cradle for removing-
refitting the engine and
transmission assembly
Mot. 1202Hose clamp pliers
Mot. 1311-06Tool for removing fuel pipes
TIGHTENING TORQUES (in daN.m)
Sub-frame front mounting bolts6
Sub-frame rear mounting bolts11
Shock absorber upper cup mounting bolts3
Wheel bolts9
Brake caliper mounting bolts3.5
Steering universal joint mounting bolt3.5
Nut for mounting rubber engine mounting
onto front left side-member mounting4.5
Put the vehicle on a two post lift.
Disconnect the battery.
Drain:
- the cooling circuit through the lower radiator
hose (radiator end),
- the engine if necessary.
Remove:
- the front wheels,
AUTOMATIC TRANSMISSION
Automatic transmission (Removal - Refitting)
23
K7M
ENGINE
- the left and right hand mudguards,
98710S
- the sub-frame-body tie-rods,
- the brake calipers and secure them to the body,
- the front bumper,
REMOVING FROM UNDERNEATH
PRG23.1
23-15

- the heat shield from the exhaust manifold,
- the catalytic converter (disconnect the oxygen
sensor) and secure the exhaust pipe to the
body,
- the horn,
- the acoustic tie-rod between the shock
absorber turrets,
- the air filter,
- the earth strap,
- the absolute pressure sensor,
- the expansion bottle and secure it to the
engine.
Disconnect:
- the accelerator cable as well as the kickdown
switch connector,
- the brake servo pipe,
- the relay plate and the electrical connectors
from the engine connection unit,
AUTOMATIC TRANSMISSION
Automatic transmission (Removal - Refitting)
23
K7M
ENGINE
- the connector from the automatic transmission
computer,
- the canister pipe.
Remove the battery mounting bracket.
- the heating pipes on the thermostat.
Unclip the radiator and move it away by securing
it to the engine.
98756R
Disconnect:
- the injection supply wire located in the scuttle
panel as well as the starter motor supply,
- the fuel inlet and outlet hoses using Mot. 1311-
06, unclip them from their support,
99461R
23-16