1995 RENAULT MEGANE SCENIC Fuel

AD4 4
ELF RENAULT MATIC D2 (D20104)
or use: MOBIL ATF 220 (D20104 or D21412)
TEXAMATIC 4011
Automatic
transmission
VALUES AND SETTINGS
Capacity - Grades
07
3 .4 Manual gearboxComponents
Capacity in
litresGradeFeatures
JB1 3 .4
Brake circuit
Brake fluids must be approved by the Technical
DepartmentSAE J 1703
and DOT 3
All countries: TRANSELF TRX 75 W 80 W
( API GL5 or MIL-L 2105 C or D standards)
Normal : 0.7
ABS : 1
Fuel tankapproximately
60
Unleaded
petrol/diesel
JB3
Separate
reservoir
1.1
Cooling circuit
F3R
F8Q
E7J - K7M
GLACÉOL RX
(type D)
Only add coolant
7
7 .5
6
Power assisted
steeringELF RENAULT MATIC
D2 or
MOBIL ATF 220
07-4

VALUES AND SETTINGS
Brake limiter
07
These vehicles are fitted with limiters which are load sensitive.
They are checked and adjusted when :
- the vehicle is unladen,
- the fuel tank is full,
- the driver is in the vehicle.
Vehicle
typeFuel tank
Front RearControl pressure (Bar)
BA0G100 72
BA0A
BA0E
BA0F
BA0L
BA0U
100Full
90966S
+0
-8
62+0
-8
07-23

Engine and peripherals
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories
from which his vehicles are constructed."All copyrights reserved by the Regie Nationale des Usines Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of the
Regie Nationale des Usines Renault.
CRégie Nationale des Usines Renault S.A.1995
ENGINE AND PERIPHERALS
TOP AND FRONT OF ENGINE
FUEL MIXTURE
FUEL SUPPLY - PUMPS
ANTIPOLLUTION
STARTING CHARGING
IGNITION - INJECTION
COOLING - EXHAUST - FUEL TANK
77 11 176 211SEPTEMBER 1995Edition Anglaise
BA0A - BA0E - BA0F - BA0G - BA0L - BA0U
cont INJECTION (Fault finding)

Contents
Consumables
Identification
Oil consumption
Oil pressure
Engine - Gearbox
Engine and transmission assembly
Sump10-1
10-1
10-2
10-3
10-4
10-19
10-43
TOP AND FRONT OF ENGINE
Timing belt
Cylinder head gasketPage Page
11
Engine and
peripherals
11-1
11-12 ENGINE AND PERIPHERALS
10FUEL SUPPLY - PUMPS -
PREHEATING
Fuel supply
Fuel cut-out on impact
Fuel gallery
Injectors
Fuel filter
Pump flow
Supply pressure
Diesel equipment
Specifications
Description of the pump
Tightening torques (in daN.m)
Special notes
Idle speed settings
Microswitches
Pump
Pump - timing
Coded solenoid valve
Operating diagram
Pre-post-heating unit
Injector holder - heater plug
Fuel filter
Coolant temperature sensor
Inlet - exhaust manifolds
Pump
Brake assistance vacuum pump
Mechanical power assisted steering
pump13-1
13-3
13-8
13-9
13-10
13-11
13-15
13-16
13-17
13-18
13-20
13-22
13-23
13-27
13-28
13-29
13-30
13-36
13-37
13-39
13-40
13-41
13-4213
FUEL MIXTURE
Specifications
Throttle body
Inlet manifold
Exhaust manifold
Manifolds12-1
12-7
12-15
12-18
12-2012

Page
COOLING
Specifications
Filling - bleeding
Checking
Radiator
Diagram
Exhaust
General
Catalytic converter
Exhaust pipe assembly
Fuel tank
Fuel tank
Filler neck
Gauge
Pump and sender unit
Engine suspension
Suspended engine mountings
Engine mounting pads19-1
19-2
19-3
19-4
19-6
19-12
19-15
19-16
19-19
19-23
19-25
19-26
19-29
19-32 COOLING - EXHAUST- FUEL TANK -
ENGINE SUSPENSION
1916-1
16-9 STARTING - CHARGING
Alternator
Starter motor
16
IGNITION - INJECTION
IGNITION
Power module
Static ignition
Spark plugs
Injection
General
Location of components
Special notes on semi-sequential
injection
Special notes on sequential injection
Injection fault warning light
Engine immobiliser function
Computer configuration as a
function of the gearbox type
17
14-1
14-9
14-13
14-19
14-21
14-22 ANTIPOLLUTION
Fuel vapour recirculation
Oil vapour rebreathing
Exhaust gas recirculation (EGR)
Catalytic converter
Catalytic converter - oxygen sensor
Test for the presence of lead
14
17-28
17-29
17-32
17-33
17-34
17-36
17-39 IGNITION - INJECTION
(continued)
Injection strategy / automatic
transmission
Injection strategy / air conditioning
Idle speed correction
Idle speed adaptive correction
Richness regulation
Adaptive richness correction
Operating wiring diagram
17
Page
17-1
17-2
17-5
17-6
17-12
17-17
17-19
17-24
17-25
17-26
Contents

ENGINE AND PERIPHERALS
Engine - Gearbox
10
E7J engine
98714R
- the relay plate and the engine connection unit
connector.
98756R
Remove the pipe from the brake servo.
Disconnect the thermistor and the fan unit feed.
Remove:
- the absolute pressure sensor,
- the ignition module,
- the fuel pipes,
- the earth strap,
- the pipe from the canister solenoid valve,
- the injection computer and secure it to the
engine,
- the starter feed wire from the battery.
Disconnect the injection feed wire located in the
scuttle panel.
98754R
Position the load positioning tool.
Lift the engine to remove the three bolts and the
engine tie-bar mounting.
Remove the engine.
REFITTING
Refitting is the reverse of removal.
Fill the gearbox and the cooling circuit and bleed
the circuit (see section 19).
NOTE: ensure the heat shields are correctly
positioned.
10-6

ENGINE AND PERIPHERALS
Engine - Gearbox
10
K7M engine
98749R
Remove:
- the heat shield from the exhaust manifold
- the catalytic converter,
- the gearbox selector rod,
- the nuts (1) from the engine and gearbox
mountings,
- the nuts (2) from the engine tie-bar mounting,
PRJ1001
- the power assisted steering pipe mountings
from the gearbox,
- the speedometer.
Disconnect the reversing light.
Remove:
- the acoustic tie-rod between the two shock
absorber turrets,
- the air filter,
- the accelerator cable from the throttle body,
- the clutch cable from the gearbox,
- the hoses (4), (5), (6), (7) and (8),
- the expansion bottle and secure it to the
wheelarch,
- the fuel supply and return pipes,
- the brake servo pipe,
- the absolute pressure sensor,
- the earth strap.
Disconnect:
- the power assisted steering and air
conditioning pressostats,
- the compressor supply and the fan unit
supply,
- the temperature switch sensor.
99167R
10-8

ENGINE AND PERIPHERALS
Engine - Gearbox
10
F (E) engine
- the relay plate and the engine connection unit
connector,
98756R
- the earth strap,
- the suspended engine mounting cover cap.
Disconnect:
- the injection computer and unclip it from the
computer mounting,
- the injection feed wire located in the scuttle
panel,
- the starter motor feed.
98754R
Remove the fuel supply and return pipes.
Remove the absolute pressure sensor.
Disconnect:
- the air conditioning and power assisted
steering pressostats,
- the compressor and fan unit supply,
- the temperature switch sensor and the oxygen
sensor,
- the canister bleed pipe.
Remove:
- the expansion bottle,
- the injection computer mounting,
- the accessories belt (see section 11),
- the power assisted steering pulley.
Remove the three bolts (1) from the power
assisted steering pump and the four bolts (2) from
the air conditioning compressor.
99502-3R
10-12