1995 NISSAN ALMERA N15 transmission oil

SEM603E
SEM717E OIL
PAN [][]
Removal (Coni'd)

b. Slide Toolbytapping onthe side ofthe Tool withahammer.
c. Remove steeloilpan.
d. Remove
bafflepl
e.

5. Remove fronttube.
6. Set asuitable transmission jackunder transaxle andhoist
engine withengine slinger.
7. Remove centermember.
8. Remove
AIT
shift control cable.
(A/T
only)
9. Remove compressor gussets.

EM-64

SEM978C
SEM980C
SEM213F TIMING
CHAIN
Removal (Cont'd)

23. Remove cylinder headoutside bolts.
24. Remove cylinder headbolts.

• Bolts should beloosened intwo orthree steps.

~5. Remove cylinder headcompletely withintake andexhaust
manifolds.
26. Remove oilpans.
Refer to"Removal" in"OIL PAN" (EM-63).
27. Remove oilstrainer.
28. Remove crankshaft pulley.
29. Set asuitable transmission jackunder mainbearing.

EM-72

SEM092DENGINE
REMOVAL
WARNING:
• Situate vehicle onaflat and solid surface.
• Place chocks atfront andback ofrear wheels.
• Donot remove engineuntilexhaust systemhascompletely
cooled off.
Otherwise, youmay burn yourself and/orfiremay break out
in fuel line.
• For safety during subsequent steps,thetension ofwires
should beslackened againsttheengine.
• Before disconnecting fuelhose, release fuelpressure from
fuel line.
Refer to"Releasing FuelPressure" inEC section.
• Besure tohoist engine andtransaxle inasafe manner.
• For engines notequipped withengine slingers, attach
proper slingers andbolts described inPARTS CATALOG.
CAUTION:
• When liftingengine, becareful nottostrike adjacent parts,
especially thefollowing: Accelerator wirecasing, brake
lines, andbrake master cylinder.
• Inhoisting theengine, alwaysuseengine slingers inasafe
manner.
Removal
1. Remove engineundercoverandhood.
2. Drain coolant frombothcylinder block,andradiator.
3. Drain engine oilfrom drain plugofoil pan.
4. Remove vacuumhoses,fuelhoses, wires,harness andcon-
nectors andsoon.
5. Remove exhausttubes,balljoints anddrive shafts.
6. Remove radiatorandfans.
7. Remove drivebelts.
8. Remove alternator, compressor andpower steering oil
pump fromengine.
9. Set asuitable transmission jackunder transaxle. Hoist
engine withengine slinger.
10. Remove centermember.
11. Remove enginemounting boltsfrombothsides andthen
slowly lowertransmission jack.

EM-99
•

SEF289HSGI233
SGI234 PRECAUTIONS
General Precautions (Cont'd)

• Before jacking upthe vehicle, applywheel chocks orother
tire blocks tothe wheels toprevent thevehicle frommov-
ing. After jacking upthe vehicle, supportthevehicle weight
with safety stands atthe points designated forproper lifting
before working onthe vehicle.
These operations shouldbedone onalevel surface.
• When removing aheavy component suchasthe engine or
transaxle/transmission, becareful nottolose your balance
and drop them. Also,donot allow themtostrike adjacent
parts, especially thebrake tubesandmaster cylinder.
• Before starting repairswhichdonot require batterypower:
Turn offignition switch.
Disconnect thenegative batteryterminal.
• Toprevent seriousburns:
Avoid contact withhotmetal parts.
Do not remove theradiator capwhen theengine ishot.
• Before servicing thevehicle:
Protect fenders, upholstery andcarpeting withappropriate
covers.
Take caution thatkeys, buckles orbuttons donot scratch
paint.
• Clean alldisassembled partsinthe designated liquidor
solvent priortoinspection orassembly.
• Replace oilseals, gaskets, packings, O-rings,locking
washers, cotterpins,self-locking nuts,etc.with newones.
• Replace innerandouter races oftapered rollerbearings
and needle bearings asaset.
• Arrange thedisassembled partsinaccordance withtheir
assembled locationsandsequence.
• Donot touch theterminals ofelectrical components which
use microcomputers (suchasECMs).
Static electricity maydamage internalelectronic compo-
nents.

GI-4

HOWTOUSE THIS MANUAL

ManualTransaxle/Transmission
Automatic Transaxle/
Transmission
Air Conditioner
Power Steering
Special Service Tools
Society ofAutomotive Engineers,

Inc.

Automatic Transmission Fluid
Drive range 1stgear
Drive range 2ndgear
Drive range 3rdgear
Drive range 4thgear
Overdrive
2nd range 2ndgear
2nd range 1stgear
1st range 2ndgear
1st range 1stgear

A/C
PIS

Tool SAE
ATF

0
1

O
2

0
3

0
4

00

2
2

2
1
1
2

1
1

•
The following
SYMBOLS ANDABBREVIATIONS
areused:

to;J,
l\tI
Tightening torque M/T

IE!
Shouldbelubricated withgrease. A/T
Unless otherwise indicated,use
recommended multi-purpose
grease.
Should belubricated withoil.
Sealing point
Checking point
Always replaceafterevery disas-
sembly.
Apply petroleum jelly.
Apply ATF.
Select withproper thickness.
Adjustment isrequired.
Service DataandSpecifications
Left-Hand, Right-Hand
Front, Rear

IE!
~

@

*

1I
SDS LH, RH

FR, RR
• The
UNITS
giveninthis manual areprimarily expressed asthe SlUNIT (International SystemofUnit),
and alternatively expressedinthe metric system andinthe yard/pound system.

"Example" Tightening torque:
59 -78 N'm (6.0-8.0 kg-m, 43-58 ft-Ib)
• TROUBLE DIAGNOSES
areincluded insections dealingwithcomplicated components.

• SERVICE DATAANDSPECIFICATIONS
arecontained atthe end ofeach section forquick reference
of data.
• The captions
WARNING
and
CAUTION
warnyouofsteps thatmust befollowed toprevent personal
injury and/or damage tosome partofthe vehicle.

WARNING
indicatesthepossibility ofpersonal injuryifinstructions arenotfollowed.

CAUTION
indicatesthepossibility ofcomponent damageifinstructions arenotfollowed.

BOLD TYPED STATEMENTS
except
WARNING
and
CAUTION
giveyouhelpful information.

GI-8

HOWTOREAD WIRING DIAGRAMS
Wiring Diagram Codes(CellCodes)

Use thechart below to'find outwhat each wiring diagram code•
stands for,

Code Section WiringDiagram Name
AACIV ECIACV-AAC
Valve
ABS BR
Anti-lock BrakeSystem
A/C HAManualAirConditioner
A/CCUT ECAir
Conditioner CutControl
A/T ATAutomatic Transmission
AIM ELHeadlamp System
AIRREG ECIACV-Air Regulator
AT/C ECA/TControl
AUDIO ELAudio
BACK/L ELBack-up Lamp
CHARGE ELCharging System
CHIME ELWarning Chime
CMPS EC
Camshaft PositionSensor
COOllF ECCooling
FanControl
DEF ELRearWindow Defogger
D/LOCK ELPowerDoorLock
DTRL ELHeadlamp
-With Daytime Light
System
ECTS ECEngine
Coolant Temperature
Sensor
EGR andcanister ControlSolenoid
EGRCIV EC
Valve
FCUT ECFuel
CutSolenoid Valve
F/FOG ELFront
FogLamp
FICO ECIACV-FICD
SolenoidValve
F/PUMP ECFuel
Pump
GLOW ECQuick-glow
system
H/LAMP ELHeadlamp
-Without Daytime
Light System
H/SEAT ELHeated
Seat
HEAT HA
Heater
HLC ELHeadlamp
Washer
H02S ECHeated
Oxygen Sensor
HORN ELHorn,
Cigarette Lighter,Clock
IATS ECIntake
AirTemperature Sensor
IGN/SG ECIgnition
Signal
ILL ELIllumination
INJECT ECInjector
INT/L ELInterior,
SpotandTrunk Room
Lamps Code
Section WiringDiagram Name
KS ECKnock
Sensor
LKUP ECTorque
Converter ClutchSolenoid
Valve
LOAD ECLoadSignal
MAFS ECMass
AirFlow Sensor
MAIN ECMain
Power Supply andGround
Circuit
METER ELSpeedometer,
Tachometer,Temp.
and Fuel Gauges
MIL ECMIL,
Data LinkConnector For
CONSULT
MIRROR ELDOOR
MIRROR
NATS ELNISSAN
ANTI-THEFT SYSTEM
02S ECOXYGEN
SENSOR
EC EVAP
CANISTER PURGECON-
PGCIV TROLSOLENOID VALVE
PLA ECPARTIAL
LOADADVANCE CON-
TROL
EC PARK/NEUTRAL
POSITION
PNP/SW SWITCH
POWER ELPOWER
SUPPLY ROUTING
POWER STEERING OILPRESSURE
PST/SW EC
SWITCH
R/FOG ELREAR
FOGLAMP
SROOF ELSUN
ROOF
SUPPLEMENTAL RESTRAINTSYS-
SRS RS
TEM
S/SIG ECST
ART SIGNAL
START ELSTARTING
SYSTEM
STOP/L ELSTOP
LAMP
TAllIL ELCLEARANCE,
LICENSE,ANDTAIL
LAMPS
TPS ECTHROTTLE
POSITIONSENSOR
TURN SIGNAL ANDHAZARD
TURN EL
WARNING LAMPS
VSS ECVEHICLE
SPEEDSENSOR
VTC ECVTC
SOLENOID VALVE
WARN ELWARNING
LAMPS
WINDOW ELPOWER
WINDOW
WIPER ELFRONT
WIPERANDWASHER
WIP/R ELREAR
WIPER ANDWASHER
GI-17

PRE-DELIVERYINSPECTIONITEMS
Shown belowarePre-delivery InspectionItemsrequired forthe new vehicle. Itis recommended that
necessary itemsotherthanthose listedherebeadded, payingdueregard tothe conditions ineach
country.

Perform applicable itemsoneach model. Consult textofthis section forspecifications .

UNDER HOOD-engine off

o
Radiator coolantlevelandcoolant hosecon-
nections forleaks

o
Battery fluidlevel, specific gravityandcondi-
tions ofbattery terminals

o
Drive beltstension

D
Fuel filter forwater ordusts, andfuel lines
and connections forleaks
[] Engine oillevel andoilleaks

D
Clutch andbrake reservoir fluidlevel and
fluid lines forleaks

o
Windshield andrear window washerand
headlamp cleanerreservoir fluidlevel

D
Power steering reservoir fluidlevel andhose
connections forleaks

ON INSIDE ANDOUTSIDE

D
Remove frontspring/strut spacer(Ifapplica-
ble)

D
Operation ofall instruments, gauges,lights
and accessories

o
Operation ofhorn(s), wiperandwasher
[] Steering lockforoperation
[] Check airconditioner forgas leaks

o
Front andrear seats, andseat belts foroper-
ation

n
All moldings, trimsandfittings forfitand
alignment

[J
Allwindows foroperation andalignment

n
Hood, trunklid,door panels forfitand align-
ment

[1
Latches, keysandlocks foroperation

rl
Weatherstrips foradhesion andfit

[l
Headlamp aiming
I~ Tighten wheelnuts(Inc. inner nutsifapplica-
ble)
IJ Tire pressure (Inc.spare tire)

Il
Check frontwheels fortoe-in
IJ Install clock/voltmeter/room lampfuse(If
applicable)
~ Install deodorizing filtertoair purifier (If
applicable)
~ Remove wiperbladeprotectors (Ifapplicable)
UNDER
BODY

o
Manual transmission/transaxle, transferand
differential gearoillevel

D
Brake andfuel lines andoil/fluid reservoirs
for leaks

D
Tighten boltsandnuts ofsteering linkageand
gear box,suspension, propellershaftsand
drive shafts
~ Tighten rearbody boltsandnuts (Models with
wooden bedonly)

ROAD TEST

D
Clutch operation

D
Parking brakeoperation

[J
Service brakeoperation

D
Automatic transmission/transaxle shifttiming
and kickdown
[] Steering controlandreturnability

o
Engine performance

D
Squeaks andrattles

ENGINE OPERATING ANDHOT

D
Adjust idlemixture andspeed (andignition
timing*1)

n
Automatic transmission/transaxle fluidlevel
~ Engine idlingandstop knob operation (Diesel
only)

FINAL INSPECTION

n
Install necessary parts(outside mirror,wheel
covers, seatbelts, mat,carpet ormud flaps)

[1
Inspect forinterior andexterior metaland
paint damage
[] Check forspare tire,jack, tools (wheel
chock), andliterature

n
Wash, cleaninterior andexterior

"1: Not required onmodels withadirect ignition system
~ :Not appiicable tothis model.
•

MA-5

ON-VEHICLESERVICE
Replacing OilSeal
DIFFERENTIAL OILSEAL

1. Drain gearoilfrom transaxle.
2. Remove driveshafts. RefertoFA section ("Removal",
"FRONT AXLE-Drive Shaft").
3. Remove differential oilseal.
4. Install differential oilseal.

• Apply multi-purpose greasetoseal lipofoil seal before
installing.

5.- Install driveshafts -Refer toFA section ("Installation",
"FRONT AXLE-Drive Shaft").

- F30A
&
F31A-
•

F30A F31A
LH and RHsides LHand RHsides

Drift

ST33400001
SMT684C
.P
-F32A
-

• Install differential oilseal sothat dimension "A"and"B"
are within specifications.
F32A
Transmission
case side Clutch
housing side
Oil seal
SMT7388
A

5.9 -6.1 (0.232 -0.240)
MT-5
Unit:
mm(in)

B

0.5 (0.020)
or
less