1994 MAZDA MX-5 ABS

R REAR SUSPENSION (DOUBLE-WISHBONE) SHOCK ABSORBER AND SPRING Removal / Installation 1. Jack up the front of the vehicle and support it with safety stands. 2. Remove in the order shown in the figure, referring to Removal Note. 3. Inspect all parts and repair or replace as necessary. 4. Install in the reverse order of removal. 5. Loosely tighten the stabilizer control link bolt. Tighten all other nuts and bolts to the specified torques. 6. Lower the vehicle. 7. With the vehicle unloaded, tighten the stabilizer control link bolt to the specified torques. 8. Adjust the rear wheel alignment. (Refer to page R-9.) Nm (kgfm, ft4bf) 1. Wheel and tire 2. Filler pipe protector (left side) 3. Stabilizer control link bolt 4. Shock absorber and spring Removal Note . . . . . . . . . . . . . page R-22 Disassembly l Inspection / Assembly . . . . . . . . . . . . . . . . page R-13 Removal note Shock absorber and spring Caution Do not lower the arms excessively, which may damage the brake hose. 1. Loosen the upper arm and Adjusting cam nuts. 2. Lower the upper and lower arms to remove the shock absorber and spring. Gartner Banana

REAR SUSPENSION (DOUBLE-WISHBONE) LOWER ARM Removal / Inspection / Installation 1. Jack up the rear of the vehicle and support it with safety stands. 2. Remove in the order shown in the figure. 3. lnspect all parts and repair or replace as necessary. 4. Install in the reverse order of removal. 5. Loosely tighten the lower arm, shock absorber, and stabilizer control link bolts. Tighten all other nuts and bolts to the specified torques. 6. Lower the vehicle. 7. With the vehicle unloaded, tighten the lower arm, shock absorber, and stabilizer control link bolts to the - specified torques. 8. Adiust the rear wheel alignment. (Refer to page R-9.) 1. Wheel and tire 2. Stabilizer control link bolt 3. Shock absorber bolt 4. Lower arm lnspect for damage and cracks 5. Lower arm bushing (crossmember side and knuckle side) lnspect for deterioration and wear Gartner Banana

R REAR SUSPENSION (DOUBLE-WISHBONE) CROSSMEMBER Removal I Inspection I Installation 1. Jack up the vehicle and support it with safety stands. 2. Remove the wheels and tires. d 3. Remove the differential and the power plant frame. (Refer to section M.) 4. Lower the crossmember and other suspension parts as an assembly, and then separate the parts. 5. Remove in the order shown in the figure. 6. lnspect parts and repair or replace as necessary. 7. Install in the reverse order of removal. 8. Loosely tighten the stabilizer bracket, upper arm, and lower arm bolts. Tighten all other nuts and bolts to the specified torques. 9. Lower the vehicle. 10. With the vehicle unloaded, tighten the stabilizer bracket, upper arm, and lower arm bolts to the specified torques. 11. Adjust the rear wheel alignment. (Refer to page R-9.) 12. Bleed the air from the brake system. (Refer to section P.) 13. Adjust the parking brake lever stroke. (Refer to section P.) 1. Differential mounting pipe 6. Shock absorber bolt 2. Parking brake cable 7. Stabilizer bracket Removal / Installation . . . . . . . . . Section P 8. Upper arm bolt 3. Brake pipe 9. Adjusting cam bolt Removal / Installation . . . . . . . . . Section P 10. Rear crossmember assembly 4. Brake pipe joint Inspect for damage 5. Battery cable bracket Gartner Banana

WINDSHIELD WIPER AND WASHER S WINDSHIELD WIPER AND WASHER TROUBLESHOOTING i/ Circuit Diagram WINDSHIELD WIPER & WASHER MAIN FUSE BLOCK MAIN BOA FUSE BLOCK // WIPER \ & 20A IGNITION SWITCH WINDSHIELD WIPER AND WASHER SWITCH i WIPER SWITCH --------------------- o -I MIST o OFF HIGH o o LOW INT I I I - MOTOR - I I I WINDSHIELO WIPER MOTOR ( ( I -01 WINDSHIELD WASHER MOTOR (F) IITHOUT ABS - ----- 'ITH ABS 1-02 WINDSHIELO WIPER MOTOR (F) 1-03 WINDSHIELD WTPER AND WASHER SWITCH(F) Gartner Banana

s WINDSHIELD WIPER AND WASHER WITH ABS A B WIPER MOTOR lnspection Check for continuity between the terminals with the wiper in parked position. Terminals A-B A-C A-D WASHER MOTOR lnspection Connect battery positive voltage to terminal A and a ground to terminal 6, and verify that the motor operates. Continuity NO Check operation by applying battery positive voltage and a ground to the terminals of the motor connector. B+: Battery positive voltage FRONT WIPER AND WASHER SWITCH lnspection Refer to Section T. Yes Yes Terminal B+ A Terminals B-C Operation speed Low Continuity NO B-D C-D No Yes Gartner Banana

WINDSHIELD WIPER AND WASHER s COMPONENTS Removal l lnstallation u 1. Disconnect the negative battery cable. 2. Remove in the order shown in the figure. 3. Install in the reverse order of removal, referring to Installation Note. WITHOUT ABS 1. Wiper arm and blade 6. Wiper link Adjustment ................ page S-42 7. Washer tank Installation Note ........... page S-42 8. Washer motor 2. Cowl grille Inspection ................. page S-38 3. Baffle cover 9. Washer nozzle 4. Fuse box Adjustment ................ page S-42 5. Wiper motor 10. Washer pipe Inspection .................. page S-38 Gartner Banana

s WINDSHIELD WIPER AND WASHER WITH ABS 1. Washer tank cover 4. Washer tank hose 2. Front bumper and bracket 5. Washer tank Removal / Installation . . . . . . . page 5-24 6. Washer motor 3. Tank bracket Inspection . . . . . . . . . . . . . . . . . page S-38 Gartner Banana

FUSE SPECIFICATIONS Main Fuse Block u I Fuse Amperes Protected circuit HEAD INJ MAIN BTN 30A 30A COOLING FAN (AD FAN) 1 ABS I 60A I Antilock brake svstem I Headlight relay, Headlight switch Alternator, Diagnostic module (for air bag system) 80A 40A ST SIG RETRACTOR Fuse Box No.1 Except circuits protected in main fuse block: INJ 30A, HEAD 30A, RETRACTOR 30A TNS relay, Headlight switch 30A 20A EGI main relay, Coolant fan relay A/C relay 10A 30A Park l Neutral switch, Circuit-opening relay Retractable headlight actuator Fuse ENGINE METER (POWER WIND) Amperes 15A WIPER TAIL ROOM I 10A I PCME, Key reminder switch, Audio unit I Protected circuit EGI main relay, Coolant fan relay 15A 30A STOP HAZARD CIGAR 15A I Cigarette lighter, Audio unit 1 Instrument cluster, Turn signal switch, Timer and buzzer unit, Cruise control main switch Power window switch 20A 15A Fuse Box No.2 Blower switch, Wiper switch Taillights, Side marker lights, License plate lights, Parking lights 15A 15A Fuse Amperes Protected circuit I Stoplight switch, Horn switch, Cruise control unit Flasher unit Fuse Color Code (DEFOG) (ANTENNA) I Fuse amperes I Color code Fuse type 25UOTX-013 20A 20A I I 10A Red 1 I Rear window defroster Power antenna Plate type 15A 20A Light blue Yellow 30A 30A 80A Light green Pink Black Cartridge type Gartner Banana