1994 MAZDA MX-5 ABS

ANTILOCK BRAKE SYSTEM (ABS) ABS WHEEL SPEED SENSOR (REAR) Removal 1 Inspection I Installation 1. Remove the filler pipe protector (left side). 2. Remove the spare tire (right side). 3. Remove in the order shown in the figure. 4. Install in the reverse order of removal. 1. Connector 2. Mud guard 3. Bolts 4. Wheel speed sensor lnspection . . . . . . . . . . . . . . . . . . . . . . . below lnspection Wheel speed sensor 1. Measure resistance between terminals of the wheel speed sensor. Resistance: 1 .O-1.2 kR 2. If not as specified, replace the wheel speed sensor. Gartner Banana

ANTILOCK BRAKE SYSTEM (ABS) P ABS SENSOR ROTOR (REAR) Removal / Inspection 1. Inspect the ABS sensor rotor for missing and damaged teeth. Note The sensor rotor does not need to be removed unless you are replacing it. 2. Remove in the order shown in the figure, referring to Removal Note. 25uopx-o: 1. Drive shaft 2. Sensor rotor Removal . :. . . . . . . . . . . . . . . . . . . section M Removal Note . . . . . . . . . . . . . . . . . . . below 3. Boot band and boot Removal note Sensor rotor Tap the sensor rotor off the drive shaft with a chisel. Gartner Banana

P ANTILOCK BRAKE SYSTEM (ABS) -.A 1. Sensor rotor 3. Drive shaft ................... ................. Installation Note below Installation section M 2. Boot and boot band ................... Installation section M lnstallation note ABS sensor rotor Set a new sensor rotor on the drive shaft and press it on with the SST. Gartner Banana

Q OUTLINE, TROUBLESHOOTING GUIDE OUTLINE Wheels SPECIFICATIONS Tires -2 TROUBLESHOOTING GUIDE Temporary spare 14x4T - - TY Pe Item Size Offset mm {in) Pitch circle diameter mm {in) Material Size Air pressure kPa {kgf/cm2, psi} Standard 14x5 112-JJ 45 11.77) 1 00 (3.94) Aluminum Alloy 185160R14 82H 177 {I .8, 26) Page Excessive or irregu- tar tire wear Premature tire wear Tire squeal body vibration I Unbalanced wheel@) 1 Adjust I Q-5 Steel T1 l5/7ODl4 41 2 {4.2,60) Action Problem 1 Tre deterioration 1 Replace I - I Deformed wheel(s) or tire(s) I Repair or replace I - Possible Cause Refer to page Q-4 for details. Road noise or I Insufficient tire pressure [ Adjust Incorrect tire pressure ( Adjust Incorrect tire pressure 1 Adjust Q-3 Q-3 0-3 Shake [Steering wheel "Ibrates Excessive tire and wheel runout Loose lug nuts Unbalanced wheel(s) Insufficient tire pressure Unevenly worn tires Malfunction of shock absorber Loose shock absorber mounting bolts Stuck or damaged lower arm ball joint Cracked or worn suspension bushings Shimmy (Steering wheel vibrates lefiIright) Replace Tighten Adjust or replace Adjust Replace Replace Tighten Replace Replace Irregular tire wear Excessive tire and wheel runout Loose lug nuts Unbalanced wheel(s) - Q4 Q-5 Q-3 - section R section R section R section R Cracked or worn engine mount Cracked or worn steering gear mount Loose steering gear mounting bolts Stuck or damaged steering ball joint I Damaged or worn front wheel bearing ( Replace ( section M Replace Replace Tighten Adjust or replace I Improperly adjusted front wheel alignment 1 Adjust I section R Uneven (one-sided) I Unequal tire pressures 1 Adjust 1 Q-3 - - Q-4 Q-5 Replace Replace Tighten Replace section B section N section N section N braking Steering wheel I Incorrect tire pressure 1 Adjust doesn't return properly or pulls to either left or right . General driving Instability Excessive steering (2-3 wheel play Irregular tire wear (lefthight) Unequal tire pressures Different types or brands of tires mixed (leftlright) Loose lug nuts Unequal tire pressures Damaged or unbalanced wheel(s) Loose lug nuts Loose lug nuts I 15UOQX-00 Replace Adjust Replace Tighten Adjust Replace or adjust Tighten Tighten - Q-3 - Q-4 Q-3 Q-5 Q-4 Q-4 Gartner Banana

Before beginning any service procedure. refer to section T of this manual for I air bag system service warnings and audio antitheft system alarm conditions . INDEX ....................................... R- 2 OUTLINE ..................................... R- 4 SPECIFICATIONS ........................... R- 4 TROUBLESHOOTING GUIDE .................. R- 5 WHEEL ALIGNMENT .......................... R- 6 PRE-INSPECTION .......................... R- 6 FRONT WHEEL ALIGNMENT ................. R- 6 .................. REAR WHEEL ALIGNMENT R- 9 FRONT SUSPENSION (DOUBLE-WISHBONE) ... R-11 PREPARATION ............................. R-11 SHOCK ABSORBER AND SPRING ............ R-11 LOWER ARM ............................... R-15 UPPER ARM ............................... R-17 STABILIZER ................................ R-19 CROSSMEMBER ........................... R-20 REAR SUSPENSION (DOUBLE-WISHBONE) .... R-21 PREPARATION ............................. R-21 SHOCK ABSORBER AND SPRING ............ R-22 LOWER ARM ............................... R-23 UPPER ARM ............................... R-24 STABILIZER ................................ R-25 CROSSMEMBER ........................... R-26 25UORX-001 Gartner Banana

INDEX INDEX FRONT SUSPENSION 1. Shock absorber and spring 3. Upper arm ....... Removal / Installation page R-1 1 Removal / Inspection / ............... Disassembly / Inspection / Installation page R-17 ................ Assembly page R-13 4. Stabilizer 2. Lower arm Removal / Inspection 1 Removal / Inspection 1 Installation ............... page R-19 -, ............... Installation page R-15 5. Crossmember Removal / Inspection / Installation ............... page R-20 Gartner Banana

INDEX R REAR SUSPENSION 1. Shock absorber and spring 3. Upper arm Removal I Installation ....... page R-22 Removal 1 Inspection 1 Disassembly 1 Inspection / Installation ............... page R-24 Assembly ................ page R-13 4. Stabilizer 2. Lower arm Removal 1 Inspection 1 L' Removal I Inspection / Installation ............... page R-25 Installation ............... page R-23 5. Crossmember Removal / Inspection 1 Installation ............... page R-26 Gartner Banana

OUTLINE OUTLINE SPECIFICATIONS Front Suspension - Transmission item (Stabilizer Specifications MT I AT - I Susoension tvoe I . , . , I . , Shock absorber Cylindrical double acting, low-pressure-gas charged I Double-wishbone TY pe Torsion bar Coil spring I - Diameter mm linl I 20.0 10.79) Identification mark color 19.0 (0.75) White Wire diameter mm (in) Coil inner diameter mm {in) I Blue Free length mm {in) Coil number 11 .O (0.43) 83 i3.27) 11 .O (0.43) 83 (3.27) 292.5 (1 1 32) 6.32 3 +. 3 (0.12 + 0.12) 0°18' + 18' Total toe-in I - I 35UORX-001 Rear Suspension 302.0 (1 1.89) 6.32 mm {in) degree Total toe-in (per side) 1 degree Front wheel alignment (Unladedt1) 0°09' +. 09' Caster anglee3 4"26' +. 45' Kingpin angle 11 "20' Maximum steering angle Transmission Specifications MT I AT Item Differential - Suspension type Inner Outer "TORSEN" LSD 1 Standard Double-wishbone Coil springs 370 23' a 2" 32" 32' -t 2" Camber anglee2 Torsion bar 12.0 (0.47) 1 11.0 (0.43) 1 11 .O (0.43) Cylindrical double acting, low-pressure-gas charged - Stabilizer Identification mark color Wire diameter mm {in) 0°24' + 45' Type Diameter mm {in) I Coil number I 7.68 I 7.96 I Shock absorber Yellow 10.1 {0.40} Coil inner diameter mm {in) Free length mm {in) Green 10.2 {0.40) 35UORX-002 *I Fuel tank full; radiator coolant and engine oil at specified levels; spare tire, jack, and tools in designated positions. '2 Difference between left and right must not exceed I O. '3 Difference between left and right must not exceed 1'30'. "TORSEN" is a registered trademark of ZEXEL-GLEASON USA.INC 83 I3.27) 348.5 j13.72) Rear wheel alignment (Unladed*') 83 (3.27) 356.5 (1 4.04) Total toe-in Total toe-in (per side) mm (in) degree degree 3 -c 3 (0.12 + 0.121 0°18' + 18' 0°09' + 09' Camber angle*2 -0°43' 2 30' Gartner Banana