Carry out the passenger seat position adjustments procedure below under each of the conditions stated below:
Key in ignition barrel
. Passenger's door open
. Passenger's closed within the last 30 seconds
0 . Auxiliary ON
Passenger seat position adjustments
1.
2.
3.
4.
5.
0
6.
7.
8.
Locate seat switch pack on the side of the seat cushion.
Operate the fore
/ aft movement control switch. Does the seat respond in the correct manner?
Yes: Proceed to step
3.
No:
Operate front and rear, raise / lower movement control switches. Does seat respond in the
correct manner in each case?
Yes: Proceed to step
4.
No:
Operate squab recline / incline movement control switch. Does squab respond in correct
manner?
Yes: Proceed to step
5.
No:
Operate lumbar pump inflate / deflate control switch. Does lumbar pad stiffen and slacken
accordingly?
Yes: Proceed to step
6
No:
Operate headrest raise / lower switch. Does headrest respond in correct manner?
Yes: Proceed to step
7.
No:
Remove key from ignition, close passenger's door and allow 30 seconds to elapse. Repeat
steps
1 - 6 and check that adjustment cannot be made.
Test complete; proceed to Memory Position Set
Abort
test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Memory
set position - passenger's side
1.
2.
0 3.
4.
5.
6.
7.
0
Insert the key in the ignition.
Operate switches to adjust seat to preferred positions.
Select 'memory' on the passenger's door switch pack. Check that switch surround
i I I um i nates.
Depress desired memory button,
1,2 or 3, on door switch pack within 4 seconds of
memory select. Check that
a chime sounds to confirm memory storage.
Operate the switches
so that memorized positions are changed. Depress relevant memory
option button,
1, 2 or 3 and check that all positional settings are restored as memorized.
Yes: Proceed to step
6.
No:
Remove key from ignition, close door and allow 30 seconds to elapse. Repeat steps 1 - 4
and check that adjustment cannot be made.
Test complete. Abort
test and refer to Diagnostic Sub
-Routines.
X300 EDM 15.4 - 15 Issue 1 August 1994
Electrical rl
15.4.8 DlAG NOSTIC SUB-ROU T1 NES
0
The following information details possible fault conditions, causes and remedies. Detail test procedures for compo-
nents are covered in 'PIN-POINT TESTS' (Sub-Section 15.4.9).
Fault:
Possible causes:
Remedy:
Fault: Possible causes:
Remedy:
0
Fault:
Possible causes:
Remedy:
Fault:
Possible causes:
Remedy: Driver's
seat adjustment inoperative
1.
2.
3. Mechanical mechanism fault.
1.
2.
3.
No power supply to SCM.
Wiring harness or connectors faulty.
Check fuses
in 'A' post base fuse boxes.
Check harness and connectors between
SCM -fuse box,
SCM
-switch pack and SCM - motors.
Identify and repair mechanical faults.
Seat positional adjustment restricted
1.
2. Motor faulty.
3. Switch faulty.
4. Mechanical mechanism fault.
5. SCM faulty.
1.
2. Renew motor.
3. Renew switch pack.
4.
5. SCM faulty.
Harness
wiring or connector fault.
Examine wiring and connectors between SCM
- switch
pack and SCM
- motors.
Identify and repair mechanical faults.
Seat lumbar pump only inoperative
1.
2.
3. Motor faulty.
4. Switch faulty.
5. Mechanical mechanism
fault.
1.
2.
3. Renew motor.
4. Renew switch.
5. No
power supply to SCM.
Harness wiring or connector fault.
Check fuses in
'A' post base fuse boxes.
Examine wiring and connectors between SCM
- switch
pack and SCM
- motors.
Identify and repair mechanical faults.
Seat heaters only inoperative
1.
2.
3. Heater element faulty.
4. Heater thermostat faulty.
5. Heater switch faulty.
6. Body processor signal fault.
1.
2.
3.
4. Renew faulty switch.
5.
No power supply to SCM.
Wiring harness or connectors faulty.
Check fuses in
'A' post base fuse boxes.
Examine harness and connectors between SCM
- heater
circuit and SCM
- BPU.
Locate and renew faulty heater and thermostat unit.
Refer to BPU fault diagnosis.
X300 EDM 15.4 - 17 Issue 1 August 1994
