1994 HONDA INTEGRA lock

Regulator Valve Body
Disassembly/lnspection/Reassembly
NOTE:
a Clean all pans thoroughly in solvent or carburetor cleaner, and dry with compressed ait.a Blow out all passages.
a Replace valve body as an assembly it any parts are worn or damaged.a Check all valves for free movement. lf any fail to slide freely, see Valve Body Repair on page 14-117.
1. Hold the .egulator spring cap in place while removing the lock bolt. Once the bolt is removed. release the spring
cap slowlv.
CAUTION: The .egulator spring c8p can pop out whsn the lock bolt is removod.
2. Reassembly is in the reverse order of the disassembly procedute.
NOTE:
. Coat all pans with ATF.
a Align the hole in the regulator spring cap with the hole in the valve body, press the spring cap into the body andtighten the lock bolt.
LOCK.BOLT6 x 1.0 mm12 N.m (1.2 kgl.m, 8.7 lbf.ftl
REGULATOR SPRING CAP
COOLER CHECK
OOWEL PINS, 2
ROLLER
SPRING SPECIFICATIONS
Unit of length: mm (in)
../
I',.-2" ll"%=
VALVE SLEEVE
t,-V
,*6t'"
REGULATOR VALVE
REGULATOR VALVE BODY
No.Spring
Standard (New)
Wiro Dia.o.D.Free LonglhNo. of Coils
o/a
@
\9/
Regulator valve spring A
Regulator valve spring B
Stator reaction spring
Lock-up control valve spring
Cooler check valve spring
Torque converter check valve spring
1.80 (O.O71)
1.80 (0.071)
5.50 (O.2171
o.80 (o.o31)
1 .10 (0.043)
1 .10 (O.O43t
14.70 (O.5791
9.60 (0.378)'26.40 (1.O39)
6.60 (O.260)
8.40 (O.331)
8.40 (0.331)
88.60 (3.488t
44.OO t't.7321
30.30 (1 .1 93t
39.50 (1.555)
33.80 (1 .331 I
33.80 (1 .331 )
16.5
2.1
25.O'l2.5
12.5
14-122
lnside Diameter

NOTE:
a Clean all paris thoroughly in solvent or carburetor cleaner, and dry with compressed air.
a Blow out all passages.
a Replace valve body as an assembly it any parts are worn or damaged.
a Check all valves tor free movement. lf any fail to slide fre€ly, see Valve Body Repair on page 14-117.
a Coat all parts with ATF before reassembly.
LOCK-UP SHIFT VALVE
LOCK.UP TIMING 8 VALVE
,ar
\,/
SPRING SPECIFICATIONS
CAP
Unit ot length; mm (in)
No.Spring
Standard {Nsw}
Wile Di8.o.D.Flee LengthNo. of Coils
o
@
Lock-up shift valve spring
Lock-up timing B valve spring
o.90 (o.035)
o.80 (o.031)7.60 (0.299)
6.60 {O.260)
73.70 i.2.9021
60.80 (2.394)32.O
22.1
Disassembly/lnspection/Reassembly
14-123

Mainshaft
Disassembly/lnspection/Reassembly
NOTE:
a Lubricate all pans with ATF during reassembly.
a Install the thrust needle bearings with unrolled edge of bearing retainer lacing washer.
a Inspect the thrust needle bearings and the needle bearings for galling and rough movement.
a Betore installing the O-rings, wrap the shaft splines with tape to prevent damaging the O-rings.
a Locknut has lett-hand threads.
RING
\
MAINSHAFTCheck splines tor excessivewear or damage.Check bearing surface for scoring,scralches or excessive wear,
CONICAL SPRING WASI{ERReplace.
LOCKNUT (FLANGE NUT)19 x 1.25 mm93 N.m {9.5 kgf.m, 69 lbf.ftlReplace.Left-hand threads
SNAP
THRUST WASHER
THRUST NEEDLEBEARING
lST CLUTCHASSEMBLY
o-ntNGsReplace.
THRUST WASHER
THRUST NEEDLEBEARING4TH GEAR
NEEOLE BEARIT{GS
4TH GEAR COLLAR
lST GEAR
THRUST WASHER
BEANING
1ST GEARCOLLAR
TRANSMISSIONHOUSING BEARING
SEALING RINGS,35 mm
2ND/4TH CLUTCHASSEMBLY
NEEDLE BEARING
THRUST NEEDLEBEARING
O.RINGSReplace.
THRUST WASHER, 36.5 x 55 mmSolective part.
THRUST NEEDLEBEAFING
2ND GEAR
SEALING RING.29 mm
NEEDLE BEARING
SET RII{G

Mainshaft
Inspection
a Clearance Measurement
NOTE: Lubricate all parts with ATF during assembly.
1 . Remove the mainshaft bearing lrom the transmission
housing (see page 14-152).
2. Assemble the parts below on the mainshaft.
NOTE: Do not assemble the O-rings while in-
specting.
LOCKNUT
/ 1ST CLUTCH ASSEMBLY
THRUST WASHER
lST GEAR COLLAR
TBANSMISSIONHOUSING BEARING
THRUST WASHER
4TH GEAR COLLAR
2ND/4TH CLUTCHASSEMBLY
THRUST WASHERSelective part.
TI{RUST NEEDLEBEARING
2ND GEAR
NEEDLE BEARING
THRUST NEEOLEBEARING
MAINSI.IAFT
14-130
3RD GEAR2ND GEAR
Torque the mainshaft locknut to 29 N.m (3.0
kgf .m, 22 lbf.ft).
NOTE: Mainshaft locknut has lett-hand threads.
29 N.m (3.0 kgl.m, 22 lbt.ft)
4. Hold 2nd gear against the 2nd clutch. then meas-
ure the clearance between 2nd gear and 3rd gear
with a feeler gauge.
NOTE: Take measurements in at least three Dlaces
and take the average as the actual clea.ance.
STANDARD: 0.05-0.13 mm {0.002-0.005 inl
THRUST WASHER-36.5 x 55 ftm
3RD GEAR 2ND GEAR

Countershaft
Disassembly/lnspection/Reassembly
NOTE:
a Lubricate all parts with ATF belore reassembly.a Install the thrust needle bearings with unrolled edge of bearing retainer facing washer.a Inspect the thrust needle bearings and the needle bearings tor galling and rough movement.a Before installing the O rings, wrap the shaft splines with tape to prevent damaging the O-rings.a Locknut has left-hand threads.
CONICAL SPRINGWASHERReplace.
LOCKNUT {FLANGE NUTI23 x 1.25 mm1O3-0-lO3N.m{10.5-O-'l0.5ksf.m,75.9*O-75.9tbf.fr)Replace.Left-hand threads
REVERSE GEAR COLLAR
NEEDLE EEARINGPARKING GEAR
ONE.WAYCLUTCHREVERSEGEAR
BEVERSESELECTOR
REVERSE SELECTORHUB
4TH GEAR
NEEDLE BEARING
DISTANCE COLLAR,28 mmSelective part.
.I ST GEAR
NEEDLE EEARING
lST GEAR COLLAR
TRANSMISSIONHOUSING BEARING
COUNTERSHAFTCheck splines for excessivewear or damage.Check bearing surface for scoring,scratches or excessive wear_
2ND GEAE
THRUST NEEDLEBEARING
3RD GEAR
NEEDLE BEARING
THRUST NEEDLE BEARING
3RD GEAR COLLAR
3RD CLUTCH ASSEMBLY
O-RINGSReplace.

Install the parts below on the countershaft sub-
assembly, then torque the locknut to 29 N'm (3.O
kgf.m, 22 lbf.ft).
LOCKNUTLeft-hand threads
CONICAL SPRI GWASHER
PARKING GEAR/ONE-WAYCLUTCH/1ST GEARASSEMBLY
NEEEDLE BEARING
lST GEAR COLLAR
TRANSMISSION HOUSINGBEARING
REVERSE GEARCOLLAR
Measure the clearance between the 2nd gear and
the distance collar, 28 mm wilh a feeler gauge.
NOTE: Take measurements in at least three places.
and take the average as the actual clearance.
STANDARD: O.O5-0.13 mm (0.OO2-O.O05 in)
DISTANCE COLLAR,28 mm2ND GEAR
2ND GEAR
(cont'd)
14-135

Transmission
NOTE:
a Coat all parts with ATF.a Replace the parts below:. O-rings. Lock washers. Gaskets. Locknuts. Conical spring washers. Sealing washers
TOROUE: 12 N.m (1.2 kgt.m, 8.7 tbf.fr)
LOCK-UP VALVEEODY
OOWEL PINS, 2
COOLER CHECK VALVE
Reassembly
Bolts,4
DOWEL PINS. 2
MAIN VALVE
OIL FEED PIPE
/ LUBRTcAToR
, PLATE
fln /
| / /""n
v{*' e'f _\
_! 1.-...-]]
-. :-,.
OOWEL PINS, 2
orLFEEDPIPES
OIL FEED PIPES
ACCUMULATOB COVER
OIL FEED PIPE
Bolts,3
e
"o't
CONTROL
E SHAFT
LOCK WASHER
SERVO DETENTBASE
REGULATOR VALVEBODY
OIL FEED PIPES
SERVO BODY
SERVO SEPARATORPLATE
EoDY | . "1-
OIL PUMP DRIVEN
GEAR SHAFT
OIL PUMP DRIVEN GEAR
MAIN S€PARATORPLATE
SECONDARY VALVEBODY
DOWEL PINS, 2
SECONDARY SEPARATORPLATE
vaLVE spRtNGS \_(< \
ToRou E coN vE RTE n \-\.--CHECK VALVE ----.-. --'r -
Bolt
14-156
ATF MAGNET

2.
1.Install the ATF magnet and suction pipe collar in the
torque converter nousrng.
Install the main separator plate with two dowel pins
on the torque converter housing. Then install the oil
pump drive gear, driven gear and driven gear shalt.
NOTE| Install the oil pump driven gear with its
grooved and chamtered side facing down.
OIL PUMPDRIVE GEAR
OIL PUMPORIVEN GEAR
Grooved and chamferedside faces separatorplate.
J.Loosely install the main valve body with Iour bolts.
Make sure the oil pump drive gear rotates smoothly
in the normal operating direction and the oil pump
driven gear shaft moves smoothly in the axial and
normal operating directaons.
Install the secondary valve body, separator plate and
two dowel pins on the main valve body.
Installthe control shaft in the housing, with the con-
trol shatt and manual valve togelher.
Install the detent arm and arm shatt in the main valve
body, then hook the detent spring to the detent arm.
SERVO SEPARATOR PLATE
--- 8ixli"'
6.
36
DETENTSHAFT
DETENT ARM
MANUAL VALVE
DETENI SPRING
17. Install the oil feed pipes.
14-157
E'.:
7. Install the servo body and separator plate with six
bolts.
8. lnstall the accumulator cover with three bolts
9. lnstall the servo detent base and ATF strainer with
three bolts and new lock washers.
10. Tighten the four bolts to 12 N.m (1.2 kgf'm, 8.7
lbf.ft) on the main valve body.
Make sure the oil pump drive gear and oil pump
driven gear shaft move smoothly same as in the step
11. lf the oil pump drive gear and oil pump driven gear
shaft do not move freelY. loosen the four bolts on
the main valve body and disassemble the valve
bodies.
Realign the oil pump driven gear shaft and reassem-
ble the valve bodies, then retighten the bolts to the
specified torque,
CAUTION: Failure to align the oil pump d1iv6n gear
shaft corroctly will result in a seized oil pump drivo
geal of oil pump drivon gear shatt.
l\
(...l
=..N
L,1ffi#
j-*/:
OIL PUMPDRIVE GEABOIL PUMP OIL PUMPDRIVEN GEAR DRIVEN GEARSHAFT
12. Install the stator shaft and stopper shatt.
13. Install the stopper shatt stay on the secondary valve
body with the bolt.
14. Install the regulator valve body with the bolt.
1 5. Install the torque converter check valve, cooler check
valve and valve springs in the requlator valve body.
16. Install the lock-up valve body, separator plate, two
dowel pins and lubricator plate with the eight bolts.
(cont'dl