1991 MITSUBISHI ECLIPSE oil

AUTOMATIC TRANSAXLE - Valve Body21-327
SERVICE POINTS OF REASSEMBLY42./33.
LOCATION OF STOPPER PLATES/SO. N-D PLATE/
19. TEFLON BALL/18. STEEL BALL
Install the stopper plates, N-D plate, teflon ball and steel
ball in the upper valve body in the positions shown in the
figure.
17. INSTALLATION OF UPPER VALVE BODY SUB ASSEM-
BLYInstall the special tool, then, after securing the upper
separating plate and the intermediate plate by the eight
installation bolts, remove the special tool.
MD998226
18. INSTALLATION OF OIL FILTER/IS. STEEL BALL/
14. RELIEF SPRINGInstall, to the intermediate plate, the oil filter, the two steel
balls, and the spring.
10. INSTALLATION OF LOWER VALVE BODY SUB ASSEM-
BLY(1) Install the special tool to the intermediate plate.
(2) Install the separating plate.

AUTOMATIC TRANSAXLE - Transfer Assembly
TRANSFER ASSEMBLY
- DISASSEMBLY AND REASSEMBLY
21-333
NElVE-35-42
Nm26-30 ft.lbs.
TFAO601
Disassembly steps
1. Cover
2. Cover gasket
3. Extension housing assembly
4. Oil guide
l I5. Transfer case sub assemblyl 6. Spacer7. O-ring
l +8. Transfer case adapter sub assembly
$?everse the disassembly procedures to reassemble.(2) l 4 : Refer to “Service Points of Reassembly”.
(3) m : Non-reusable parts

AUTOMATIC TRANSAXLE- Extension Housing Assembly 211337
EXTENSION HOUSING ASSEMBLY
- DISASSEMBLY AND REASSEMBLY
NZlVGAA
>-
Disassembly steps
l +1. Air breather2. Dust seal guardl * 3. Oil seal4. Extension housing
NOTE(I) Reverse the disassembly procedures to reassemble.(2) W : Refer to “Service Points of Reassembly”.(3) q : Non-reusable parts
R3
MD99881 2MD998822
TFA03192010043
SERVICE POINTS OF REASSEMBLY
3. INSTALLATION OF OIL SEALUsing the special tool, install the oil seal.
1. INSTALLATION OF AIR BREATHER
Apply sealant to the air breather port and fit the air breatherin position.
Specified sealant: MOPAR Part No.4318025 or equiva-lent

AUTOMATIC TRANSAXLE- Transfer Case Sub Assembly 21-341
TRANSFER CASE SUB ASSEMBLY
- DISASSEMBLY AND REASSEMBLY
NZlVJAA
Ii35-42
irn26-30 ftlbs.
Disassembly steps
1.Transfer cover
2.O-ring
r)+3.Spacer4.Outer race
5. Drive bevel gear shaft
6.Outer race
**7.Spacer
I)+ 8. Oil seal9.Transfer case
10. Drive bevel gear
~~ e+ 11. Taper roller bearing~~ e+ 12. Taper roller bearing
TFA0603
NOTE(1) Reverse the disassembly procedures to reassemble.(2) +e : Refer to “Service Points of Disassembly”.(3) ~~ : Refer to “Service Points of Reassembly”.(4) m : Non-reusable parts

21-342AUTOMATIC TRANSAXLE -Transfer Case Sub Assembly
MD99891 2\
MD998827.
MD998812
MD998818
TFA0302
SERVICE POINTS OF DISASSEMBLY11./12. REMOVAL
OF TAPER ROLLER BEARINGSriUsing the special tool, remove the taper roller bearing.
-I
SERVICE POINTS OF REASSEMBLY
12./l 1. INSTALLATION OF TAPER ROLLER BEARINGSUsing the special tool, install the taper roller bearing.
r,
8. INSTALLATION OF OIL SEALUsing the special tool, install the oil seal.

22-6WHEELS AND TIRES - Wheel and Tire
INSTRUCTIONS FOR ALUMINUM TYPE
WHEELSUzzGfM
1. Aluminum is vulnerable to alkalies. If a vehicle
washing detergent has been used, or salt from
sea water or road chemicals has adhered, washthe vehicle as soon as possible. After washing
the vehicle, apply body or wheel wax to the
aluminum type wheels to prevent corrosion.
2. When cleaning the vehicle with steam, do not
direct steam onto the aluminum type wheels.
When tightening nuts for aluminum type
wheels, particularly observe the following:
(1) Clean the hub surface of aluminum type
wheels.(2) After finger-tightening wheel nuts, tighten
them to specifications.
(3) Do not use an impact wrench or push the
wrench by foot to tighten the wheel nuts.
(4) Do not apply oil to the threaded portions.
INSTRUCTIONS FOR TIRE CHAINS AND
SNOW TIRESNZZGGAA
1.Use tire chains only on front wheels. Do not usetire chains on rear wheels.
2. When using snow tires, use them on all four
wheels for maneuverability and safety.
INSTRUCTIONS FOR COMPACT SPARE
TIRE;c.1. The compact spare tire is designed to. save
space in the luggage compartment, and its
L’lighter weight makes it easier to use if a fiat tire
occurs.
2.The following instructions for the compact sparetire should be observed.
(1) Check the inflation pressure after installing
the spare, and adjust to the specified pres-
sure.(2) Avoid driving through automatic car washes
and over obstacles that could possibly dam-
age the vehicle’s undercarriage. Because
the tire is smaller than the original tire, car
ground clearance is slightly reduced.
(3) The compact spare tire should not be used
on any other wheels, nor should standard
tires, snow tires, wheel covers or trim rings
be used with the compact spare wheel. If
such use is attempted, damage to these
items or other vehicle components may
occur.

23-2
SPECIFICATIONS
GENERAL SPECIFICATIONS
BODY - Specifications
N23CA--
Items
Hood
We
Door
Construction
Regulator system
Locking system
Liftgate
We
Slass installation method
Windshield glass
Quarter window glass
Liftgate window glass
Zlass thicknessmm (in.)
Windshield glass
Liftgate window glass
Door glass
Quarter window glass
‘ower window motor
Type
Revolutions under no loadwm
Revolutions under load
wmAt 1
Nm t.72 ft.lbs.1At 2
Nm (1.45 ft.lbs.1Bound current A
Direction of rotation
‘ower window main switch
Type
Rated load currentA
Lock switch
Power window switch
‘ower window sub switch
TvwRated load current A
‘ower window relay
Maximum contact currentA
Rated coil currentA
Voltage drop between terminalsV(At 12 V and the rated load current)
Specifications
Rear hinged, front opening type
Front-hinged, sash construction
Wire type
Pin-fork type
Inner-hinged, with gas damper
Adhesive type
Adhesive type
Adhesive type5.3
i.21)3.5
t.1413.5
t.1413.5
t.141
Permanent magnet type (Built-in circuit breaker)
75 or more65-95
50-80
34 or less
Clockwise and counter-clockwise
Automatic reset type
10
10
Automatic reset type
10
20
Max. 0.2
0.2 or less

BODY - Specifications23-3
Items
Door lock control unitEffective voltage
V
Current consumption (when not in operation)
Door lock power relay
Range of voltage used
V
Rated load current (at 13.5 VIA
Rated coil currentA
Voltage drop between terminalsV
Door lock actuator
Bound current (at 12 VIA
Operating voltage rangeV
l Tripping time (at 12 V)second
Remote control mirror
Remote control mirror motorBound current
mA
Operating voltage range
V
Door mirror control switchRated load
mA
4utomatic seat belt motor
TypeRated voltage
V
No-load speedwmNo-load current A
mASpecifications
lo-16
3 or less8-16
10
0.2 or less
0.2 or less2.5-4.5
9-15
5-30
500 or less
9.5-l 5
50
Ferrite magnet motor
12
140
4
NOTEl : Tripping time is the time consumed until current reaches 0.5 A after power connection.
SERVICE SPECIFICATIONSN23CB--
ItemsSpecifications
Standard valueDoor
inside handle playmm (in.)2.5-8.5 (.09-,331
Door outside handle playmm (in.)2.5-6.5 (.09-.25)
TORQUE SPECIFICATIONS
ItemsNmft.lbs.
Hoodhingetohood9-14
7-10
Hoodhingetobody(bolt)17-2612-19
Hoodhingetobody(nut)9-147-10
Hoodlatchtobody7-115-8