1991 MITSUBISHI ECLIPSE brake

BRAKES -El cteronic Control Unit /Parking Brakes
PARKING BRAKESREMOVAL AND INSTALLATION
*i(Refer to GROUP 23-Floor Console.)
SERVICE POINTS OF INSTALLATION
2. INSTALLATION OF ELECTRONIC CONTROL UNIT%When installing the electronic control unit to the bracket,
fasten the connector’s ground wire to the bracket.
After connecting the connector to the electronic control
unit, secure the connector by the holding spring.
Post-installation Operation
aParking Brake Lever Stroke Adjust-
NOSYA-
Parking brake lever removal steps
1. Adjusting nut2. Parking brake stayl + 3. Bushing4. Parking brake switchW 5. Parking brake lever
I I6 7
h
Parking brake cable removal steps
1. Adjusting nut6. Parking clip7. Retainer springl * 8. Parking brake cable
l?TFeverse the removal procedures to reinstall.(2) +e : Refer to “Service Points of Removal”.(3) I)4 : Refer to “Service Points of Installation”.
4

BRAKES - Parking Brakes5-89

Removal steps of the parking brake lever1. Adjusting nut
2. Parking brake stay
W 3. Bushing
4. Parking brake switch
l +5. Parking brake lever
Removal steps of the parking brake cable1. Adjusting nut
::6. Parking clip
7. Retainer spring
l + 8. Parking brake cable
14A0527
Pre-removal OperationaRemoval of Floor Console (Refer toGROUP 23-Floor Console)
@Parking Brake Lever Stroke Adjustment
l installation of
Floor Console (Refer to
NOTE(1) Reverse the removal procedures to reinstall.(2) 4e : Refer to “Service Points of Removal”.(3) l 4 : Refer to “Service Points of Installation”.
SERVICE POINTS OF REMOVAL
N05YBAJ
6. REMOVAL OF PARKING CLIP/7. RETAINER SPRING
Remove the parking clip and retainer spring and disconnectthe parking brake cable from the rear brake
as&mbly.
INSPECTIONNO5YCAIl Check the parking brake lever ratchet for wear.
lCheck the parking brake lever for damage and operation.

5-90BRAKES - Parking Brakes
Identification markSERVICE POINTS OF INSTALLATION
NO!iYDAKa
8. INSTALLATION OF PARKING BRAKE CABLECheck the parking brake cables for an identification
markand install as appropriate on the left and right sides.
ItemFWDAWDI
IdentificationLeft sideNoneYellow
markRight sideWhiteOrange
5.APPLICATION OF GREASE TO PARKING BRAKE LEVER
Apply a coating of the specified grease to each slidingpartsof the ratchet plate or the ratchet
pawl.
Grease: MOPAR Multi-mileage Lubricant
Part No. 2525035 or equivalent
Cross-section A-ACross-section B-B
14A041114AO442
&=4--
13. APPLICATION OF GREASE TO BUSHING
Apply a coating of the specified grease to the inner surfaceof the bushing.
Grease: MOPAR Multi-mileage 1 lhifinnt
Part No. 2525035 or eq
._I. ..v-.--uivalent
114A0414

CLUTCH - Specifications/Special Tool6-3
TORQUE SPECIFICATIONSNMCC-Items
Nmftlbs.Clutch pedal to clutch pedal support bracket
20-2514-18
Clutch pedal support bracket
8-12
6-9
Clutch pedal support bracket to firewall
10-157-l 1Stop light switch
10-157-11
Brake booster installation nut
11-17
8-12
Master cylinder to firewall
10-157-11
Pedal rod to clutch pedal support bracket
17-2612-19
Clutch pedal bracket
8-l 26-9
Pedal rod to clutch pedal bracket
17-2612-19
Clutch tube flare nut
13-17
9-12
Air cleaner bracket
8-12
6-9
Clutch tube clamp to body
8-l 26-9
Reservoir band
5-7
4-5
Clutch release cylinder
15-22
11-16Clutch release cylinder to union bolt
2518Bleeder plug
9-13
7-9
Fulcrum35-4225-30Clutch cover assembly
15-22
11-16
- LUBRICANTSNOSCD-Items
Contact surface of release bearing and fulcrum of clutch
release fork
Inner surface of clutch release bearing
Inner surface of clutch disc splineSpecified lubricants
MOPAR Multi-mileage Lubricant
Part
No.2525035 or equivalent
Contact portion of release fork to release cylinder push rod
Bushing,
clevis pin, washer and bushing
Inner surface of clutch release cylinder and outer
circumference of piston and cupMOPAR Brake Fluid/Conforming to
DOT3Inner surface of clutch master cylinder and outer
circumference of piston assembly
SPECIAL TOOL
ToolNumber
MD9981 26
NameUse
Clutch disc center
guideClutch disc center hole alignment
\\

6-6CLUTCH - Service Adjustment Procedures
5.If the clutch pedal free play and the distance between the
clutch pedal and the firewall when the clutch is disengageddo not agree with the standard values, it is probably the
A
result of either air in the hydraulic system or a faulty master2
cylinder or clutch. Bleed the air, or disassemble and inspectthe master cylinder or clutch.
BLEEDINGWhenever the clutch tube, the clutch hose, and/or the clutch
master cylinder have been removed, or if the clutch pedal is
spongy, bleed the system.
Caution
Use the specified fluid. Avoid using a mixture of the
specified fluid and other fluid.
Specified fluid: MOPAR Brake Fluid/Conforming to DOT3

CLUTCH - Clutch Pedal6-7
CLUTCH PEDAL
-. REMOVAL AND INSTALLATIONNOSPA-
.“-Pre-removal Operation
*Removal of the Lap Cooler Duct,Shower Duct (L.H.) and Knee Pro-tector (Refer to GROUP 23%lnstru-ment Panel.)*Removal of the Steering ColumnAssembly (Refer to GROUP 19-Steering Wheel and Shaft.)*Removal of the Relay Box (Indoor)
17-26 Nm
12-19 ft.lbs.
11-17 Nm
8-12 ft.lbs.
IO-15 Nm’ tl(i/\:/ Fl/Yv .1-m.---I- I I KIDS.Post-installation Operation
l installation of the Relay Box (Indoor)l installation of the Steering ColumnAssembly (Refer to GROUP 19-Steering Wheel and Shaft.)l installation of the Lap Cooler Duct,Shower Duct (L.H.) and Knee Pro-tector (Refer to GROUP 23 Instru-ment Panel.)l Adjustment of the Brake Pedal (Re-fer to GROUP 5-Service Adjust-ment Procedures.)aAdjustment of the Clutch Pedal (Re-
fer to P.6-5.)
!
:k -16
20-25 Nm
14-f8 ft.lbs.
Removal steps
I, Clutch pedal return spring 2. Brake pedal return spring3. Interlock switch
4. Clutch switch control system>
5. Bolt system>6. Stop light switch
7. Clip
l + 8. Bushing
9. Turn over spring
e+ IO. Bushing11. Cotter pinl + 12. Washerl + 13. Clevis pin14. Pedal support bracket assembly
15. Clutch pedal mounting nut
16. Clutch pedal bracket17. Lever
l + 18. Clutch pedal bushing~~ 19. Clutch pedal bushing
20. Pedal rod
e+ 21. Brake pedal bushings
22. Clutch pedal
23. Brake pedal
24. Pedal pad
NOTE(1) Reverse the removal procedures to reinstall.(2) l + : Refer to “Service Points of (3) m : Non-reusable parts

6-12CLUTCH - Clutch Master CylinderResew&r
bandk
oaA0058
08Y517
Grease
SERVICE POINTS OF REASSEMBLYNaaNciAN
6. INSTALLATION OF RESERVOIR BAND
Tighten the resetver band at the illustrated position.
4. APPLICATION OF CLUTCH FLUID TO PISTON ASSEM-
BLYApply specified clutch fluid to the inner surface of the
cylinder and to the entire periphery of the piston assembly.
Specified fluid: MOPAR Brake Fluid/Conforming to
DOT3
2. APPLICATION OF GREASE TO PUSH RODApply a suitable amount of rubber grease on the contact
surfaces between the damper push rod and piston and
between the push rod and boot.

6-14CLUTCH - Clutch Release CylinderDISASSEMBLY AND REASSEMBLY
Post-reassembly Operationl installation of the Clutch ReleaseCylinder (Refer to P.6-13.)

/e
,, #,,“”
7
3
2-36CLO37
,---a
#,J,,, ‘::.”/,,,,d$’ ’.,:..a
<
/ : i 01‘, ., 1
3
Disassembly steps
I. Valve plate2. Spring
6
3. Push rod4. Boots
6CLOOlO
*+ l 5. Piston and cup6. Conical spring
7. Cap
8. Bleeder plug
9. Release cylinder
NOTE(1) Reverse the removal procedures to reassemble.(2) W : Refer to “Service Points of Disassembly”.(3) I)4 : Refer to “Service Points of Reassembly”.
rISERVICE POINTS OF DISASSEMBLYNOOLBAE
5. DISASSEMBLY OF PISTON AND CUP(1) Remove the corrosion from the piston-removal port of
the release cylinder.
(2) Remove the piston from the release cylinder using
++,compressed air.
-JCaution
1.Cover with rags to prevent the piston from popping
out.
2.Apply compressed air slowly to prevent brake fluidfrom
splashing.