1991 MITSUBISHI 3000GT service

IQ-WHEEL STEERING SYSTEM (4WS) - Control Valve37B-9CONTROL VALVE
Pre-removal Operationl Cleaning of Pipings with Steaml Dratning of Power Steering Fluid(Refer to GROUP 37A - Service Adjustment
Procedures.)
l Removal of Rear Suspension Assembly(Refer to GROUP 34- Rear Suspension Assembly.)
El56I.I
--
iEl7’
1Post-installation Operationl Installation of Rear Suspension Assembly(Refer to GROUP 34 - Rear Suspension Assembly.)l Refillrng and Bleedrng of Power Steering System
(Refer to GROUP 37A-Service AdjustmentProcedures.)l Bleeding of 4WS System(Refer to P.37B-4.)l Checking of 4WS System for Operation
(Refer to P.37B-5.)
M37UA- -
12 Nm
35 Nm24Nm15Nm9 ftlbs.25 ft.lbs.17ft.lbs.
R \
ft.lbs.113012 Nm.\,9ft Ihc
REMOVAL AND INSTALLATION
LRemoval steps
1.Pressure hose2.Pressure tube3.O-ring
4. Pressure tube (RR)
5.O-ring6. Pressure tube (RL)
7.O-ring8. Pressure tube (FL. FR)9.O-ring10.Return pipe11.O-ring
cd
12.Control valve
\35 Nm25 ftlbs.
13FOO25TSB Revision

37B-10$-WHEEL STEERING SYSTEM (4WS) - Rear Oil Line
REAR OIL LINEM37YFv -
REMOVAL AND INSTALLATION
35 Nm25 ftlbs.
\Removal steps
12 Nm9 ftlbs.
13FOO24
1. Return hose
2. Suction hose
3. Protector
4. Pipe assembly to pressure
tube connection
5. Pipe assembly
6. Suction hose
7. Rubber hose
8. Feed pipe assembly
9. Return pipe assembly
10. Pressure tube assembly to
pipe assembly connection
11. Suction hose
12. Reserve tank
l Cleaning of Pipings with Steam
Post-installation Operationl Refilling and Bleeding of Power Steering System
(Refer to GROUP 37A-Service AdjustmentProcedures.)l Bleeding of 4WS System
(Refer to P.37B-4.)l Checking of 4WS System for Operation
(Refer to P.37B-5.)
INSPECTIONM37YCAnl
Check tubes and pipes for cracking, damage or corrosion.
l
Check hoses for cracking, damage, leakage or fluid seep-
age.l Check flare nuts for damage.
TSB Revision
I

4-WHEEL STEERING SYSTEM (4WS) - Rear Oil Pump37B-11
REAR OIL PUMP
REMOVAL AND INSTALLATION/
l Draining of Power Steering Fluid
(Refer to GROUP 37A- Service Adjustment
l Removal of Main Muffler Assembly(Refer to GROUP 15 - Exhaust Pipe and Muffler.)
Post-installation Operationl Installation of Main Muffler Assembly(Refer to GROUP 15 - Exhaust Pipe and Muffler.)l Refilling and Bleeding of Power Steering System
(Refer to GROUP 37A- Service AdjustmentProcedures.)l Bleeding of 4WS System
(Refer to P.37B-4.)l Checking of 4WS System for Operation
(Refer to P.37B-5.)
IIO-130Nm80- 94 ft.lbs.Removal steps
1. Rear shock absorber lower mounting bolt4*2. Crossmember bracketa*3. Crossmember mounting nut4.~rry~~,ff~h;t~Jside)
5.Suction hose6. Rear-wheel oil pump7. O-ring80
-94ft.lbs.
13FOO23
NOTEDo not disassemble the rear-wheel oil pump.
M3?MA- -12AOlOS
3
SERVICE POINTS OF REMOVALM37MBAA
2. REMOVAL OF CROSSMEMBER BRACKET / 3. CROSS-MEMBER MOUNTING NUT (ON DIFFERENTIAL SIDE)
(1) Support the differential case with the transmission jack,
then remove the crossmember bracket and crossmem-
ber mounting nut (on the differential side).
(2) Slightly lower the crossmember.
2TSB Revision

42-1
BODY
CONTENTSM42AA- -
CENTER PILLAR GLASS........................................................32
CENTRAL DOOR LOCKING SYSTEM
................................55
DOOR ASSEMBLY....................................................................40
DOOR GLASS AND REGULATOR
........................................42
DOOR HANDLE AND LATCH
................................................54
DOOR TRIM AND WATERPROOF FILM
............................41
DRIP LINE WEATHERSTRIP....................................................65
ENGINE HOOD........................................................................18
FENDER*....................................................................................23
FUEL TANK FILLER DOOR
....................................................22
LIFTGATE....................................................................................20
LIFTGATE GLASS....................................................................37
LOOSE PANEL
........................................................................24
POWER WINDOW
....................................................................43
QUARTER WINDOW GLASS
................................................33SERVICE ADJUSTMENT PROCEDURES
............................
Door Adjustment................................................................Door inside Handle Play Check............................................Door Window Glass Adjustment........................................Floor Pan inspection............................................................Fuel Filler Door Adjustment................................................Hood Adjustment................................................................Liftgate Adjustment............................................................
SPECIAL TOOLS........................................................................
SPECIFICATIONS....................................................................
General Specifications........................................................Sealants and Adhesives........................................................
ServiceSpecifications........................................................
TROUBLESHOOTING............................................................
WINDOW GLASS....................................................................
WINDSHIELD............................................................................
13
14
16
14
17
14
13
13
4
2
2
3
3
5
25
28
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the
SRS or any SRS-related component.

BODY - SDecifications
L
)
L
Item
Door lock power relay
Range of voltage used
V
Rated load current (at 13.5 VIA
Rated coil current
A
Voltage drop between terminals
V
Door lock actuator
Bound current (at 12
V)A
Operating voltage range
V
*Tripping time (at 12 VIsecond
Specifications8-16
IO
0.2 or less
0.2 or less
2.5
- 4.59-15
5-30
NOTE*: Tripping time is the time consumed until current reaches 0.5 A after power connection
SERVICE SPECIFICATIONSM42CB. -
ItemsStandard value
Play of door inside handlemm (in.)
A (play)
B (OPEN)
C (FULL)
Adjustmentof glass
inclination
amountFront pillarRoof
7 (.28)
46 f 9 (1.81 31 .35)
69 (2.72)
11.7 I!I 1 .O (.46 ?I .04)
11.8 f 1 .O (.46 + ,041L
SEALANTS AND ADHESIVES
Adjustment
of glass
longitudinal
inclinationQuarter pillar
Front
pillar
Roof
Quarter pillar20.5
f 1 .O (.80 f .04)7.0
i 1 .O (.28 -+ ,0417.7
If: 1 .o i.30 5 ,04112.0
f 1 .o I.47 + .04)
M42CE- -
Items1 Specified sealantRemarks
Front fender panel
Splash shield
Waterproof film
3M ATD Part No. 8625 or equivalentRibbon sealer
Windshield3M SUPER FAST URETHAN 8609 or equivalentQuarter window glass.and 3M SUPER FAST URETHAN PRIMER 8608
Liftgate glassor equivalentTSB Revision

BODY - Service Adjustment Procedures42-13
SERVICE ADJUSTMENT PROCEDURES
HOOD ADJUSTMENTM42FAA.L
1.Loosen the hood mounting bolts, and then adjust the hood
by moving it so that the clearance is equal on all sides.
2. Turn the bumpers A and B, adjust the height of the hood.,’
ii
18P058t
3.Loosen the hood latch mounting bolts, and move the hood
latch to adjust the attachment between the hood latch and
hood striker.
LIFTGATE ADJUSTMENTM42FCAF
1.Loosen the liftgate hinges mounting bolts, and then adjust
the
liftgate by moving it so that the clearance is equal on all
sides.
2. Turn the bumper to adjust the liftgate height.
3. Loosen the
liftgate latch mounting bolts, and move the
liftgate latch to adjust the attachment between the liftgate
latch and
liftgate striker.
TSB Revision

42-14BODY - Service Rdiustment ProceduresMB990834-0118A0381
18Ac-46118A0465FUEL FILLER DOOR ADJUSTMENT
M42FDAFLoosen the fuel filler door mounting screw and adjust the fuel
filler door so that the clearance around the fuel filler door is
even without any height differences.
DOOR ADJUSTMENT
M42FEAG
1.Use the special tool to loosen the hinge mounting bolts on
the body side, and then adjust the clearance around the
door so that it is uniform on all sides.
2.If the door is not flush with the body, remove the spring pin
from the door check, use the special tool to loosen the bolts
for mounting the door hinges to the door. Move the door to
adjust the door position along the body surface.
CautionAttach protection tape to the fender edges where the
hinge is installed.
3.If the door does not open freely, adjust the engagement of
the striker with the door latch by means of the striker
mounting shim and move the striker up and down or from
side to side.DOOIR WINDOW GLASS ADJUSTMENT
M42FFAL
1. Remove the door trim and waterproof film. (Refer to
P.42-41.)2. Remove the front pillar trim.
3. Remove the drip line weatherstrip.
4. Loosen the bolts and nuts of the following parts.
l Glass guide front track
l Glass guide rear track
l Delta sash
l Stabilizer inner front
l Stabilizer inner rear
. up stop
l Door belt line outer weatherstrip
NOTEMove the window glass down to the lowest position before
removing the delta sash bolt.
1 TSB Revision-1

BODY - Service Adjustment Procedures42-15lSFO15
2
5 mm (20 in.)
14.5 mm
(.57 in.)
Stabilizer
inner rear
I18FO15‘5. Remove the stabilizer inner front and adjust the adjusting
bolt for the dimension shown here.
6. Adjust the adjusting bolt for the stabilizer inner rear
dimension shown here.
7. Raise door window glass. Push glass against the outer
stabilizer of the door belt line outer weatherstrip and insert
cloth or the like between the door inner panel and glass.
8. Adjust glass to have standard clearance between the weatherstrip holder and window glass.
Caution
Measure the clearance, specified in section A-A, B-B and C-C, at the corresponding weatherstripholder screws as
shown in the illustration.
Adjustment procedures
of theglass guidereartrack same amount.
18N0114
Adjust-Move the stabilizer Inner front and
ment ofup stop up and down to adjust
forwardthe forward or rearward tilt of
or back-glass when glass is fully closed.2 ward tilt
of glass Caution
Do not turn the stabilizer
inner front adjusting bolt.
Stabilizer
inner front17.07.712.0iI 1.0+ 1.0iz 1.0-(.28 -i.30-t.47t ,041z!z .04)IL .04)
P
18FOl62
TSB Revision