1991 MITSUBISHI 3000GT rims

52A-12INTERIOR - Trims
19POO70
4Trim
19POO80
hornm
in.)
19POO8,
Pin
Trim
19POO8219POO80TRIMS
IM52UCW
TRIM CLIP REMOVAL/INSTALLATION
PROCE-DURES
The type of clip shown in the illustration, which is used for the
Eli ~
installation of instrument panel, should be removed and
installed by the following procedures described below.
REMOVAL
(1) Use a cross-tip (+) screwdriver to push inward the pin (at
the center of the trim clip) to a depth of about 2 mm
(.08
in.).(2) Pull the trim clip outward to remove it.
Caution
Do not push the pin inward more than necessary
because it may damage the grommet, or the pin may
fall in, if pushed too far.
INSTALLATION
(1) With the pin pulled out, insert the trim clip into the hole in
the trim.
(2) Push the pin inward until the pin’s head is flush with the
grommet.
(3) Check whether the trim is secure.
TSB Revision

INTERIOR - Trims52A-13EMOVAL AND INSTALLATION
19FOO33
Scuff plate
D-D1Quart&
upper trim19FOO2C
1B-B
Front piiar trimc-cIQuart&
upper trim
,wca*
Rear roof rail trim 1 igFoo22Cowl side trim removal steps
1. Scuff plate
2. Cowl side trim
Front pillar trim removal steps
4. Hanger bracket
5. Sash guide cover mounting bolt
6. Clip
7. Front pillar trimRear roof rail trim removal steps
8. Screw
10. Rear roof rail trim
Quarter upper trim removal steps
3. Quarter trim (Refer to
P.52A-14.)48: ;;;;anger9. Quarter upper trim
1 TSB Revision
NOTE(1) @: Location of metallic clip(2) c: Location of resin clip(3)* indicates trim clip. (Refer to P.52A-12.)(4)For door trim,. refer to GROUP 42 - Door TrimandWaterproof Film.
I

52A-14
INTERIOR - Trims
Scuff plate
19FOO46
33 ftlbs.19FOl60
Quarter trim removal steps
** ** 11. Rear seat
12. Shelf cover assembly
13. Shelf catcher
14. Cover
15. Garnish19. Rear seat belt anchor plate mounting bolt
20. Screw
21. Quarter trim
22. Rear side trim (Refer to
P.52A-15.)23. Quarter trim bracket
16. Sash guide cover mounting bolt
17. Front seat belt anchor plate mounting bolt
18. Retractor cover
NOTE*: Location of resin clipSERVICE POINT OF REMOVAL
11. REMOVAL OF REAR SEAT
With the lever pulled forward, raise the seat cushion to
remove it.
TSB Revision

INTERIOR - Trims52A-15

ISERVICE POINT OF INSTALLATION
11. INSTALLATION OF REAR SEAT
(1) Fit the seat cushion attachment wire under the seat-back positively.
(2) Pass the rear seat belt buckles through the. seat
cushion.
(3) Insert the lock plate of seat cushion in the hole provided
in the floor positively.
4-A{-
Rear endtrimB-Br-Rear side trim, rear end trim removal steps
I. Luggage compartment floor box (R.H.)2. Luggage compartment floor box (L.H.)9. Luggage compartment light connector con-
nection_ -10. Hear side trim
NOTE(1) @ : Location of metallic clip(2) * : Location of resin clip 3. Lid
(R.H.)4. Lid (L.H.)5. Rear end trim
6. Screws
7. Floor mat mounting clip
8. High floor center board
1 TSB Revision

52A-16INTERIOR
- Trims
A-AIB-B[
1Liftgate lower trim
Clip
Liftgate lower trim
D-D
Liftbate side trim19FO173Liftgate trim removal steps
1. Shelf hook
2.
Liftgate lower trim
3. Liftgate upper trim
4. Liftgate side trim
19FOO27
NOTE(1) @: Location of metallic clip(2) l: Location of resin clip
1 TSB Revision