1991 MITSUBISHI 3000GT oil pressure

GENERAL - Master Troubleshootina00-27HARD STEERING
L
L
Symptom
Hard steeringProbable causeLoose power steering oil pump belt
Reference page or remedy37A-8
1POOR RETURN OF STEERING WHEEL TO CENTER
Symptom
Poor return of steering wheelto center
Probable cause
Improper front wheel alignment
Improper tire pressure
Excessive tightened rack support cover
Damaged front wheel bearing
Reference page33A-4
31-3
37A-1926-10
Low fluid levelReplenish
Air in power steering system37A-10
Low tire pressure
313
Excessive turning resistance of lower arm ball33A-9joint
Excessively tightened steering gear box
rack support cover
37A-19
Improper front wheel alignment
Excessive turning resistance of tie-rod ball
joint
Sticky flow control valve
Bent rack in steering gear box33A-437A-6
37A-30
37A-19
TSB Revision1

GENERAL - Master Troubleshootinn
VEHICLE PULLS TO ONE SIDE
Symptom
Vehicle pulls to one sideProbable cause
Improper front or rear wheel alignmentReference page or remedy33A-4
34-5,23
lmbalanced or worn tires
Uneven tire pressure31-3
Excessive turningresistance of lower arm ball33A-9
I--_Wheel beanng serzureReplace
I---Broken or worn coil spring33A-5Ir
~~~~~~Bent front or rear axle drive shaft126-11I
I-Deformed lower arm1 33A-8I
Improper tire pressure31-3
lmbalanced wheelsReplace
Poor turning resistance of lower arm ball joint33A-9
Excessive play of steering wheel37A-5
Broken or weak front stabilizer33A-10
Worn lower arm bushing33A-8
Malfunctioning shock absorber33A-5
34-l 3,33
Broken or weak coil spring
Wear, play, or seizure of wheel bearing
Wear, play, or seizure of drive shaft ball jointReplace
26-l 127-l 8 STEERING WHEEL SHIMMY
SymptomProbable cause
Steering wheel shimmyImproper front or rear wheel alignmentReference page or remedy33A-434-5,23
Boll-OMING
Symptom
BottomingProbable cause
Overloaded vehicleReference page or remedy
Correct
Broken or weak coil spring33A-5
34-l 3.33
IMalfunctioning shock absorber
1 TSB Revision

GENERAL - Maintenance Service00-39ogPOO268. ENGINE OIL FILTER (Change)
MOOEAEJThe quality of replacement filters varies considerably. Only high
quality filters should be used to assure most efficient service.
Genuine oil filters require that the filter be capable of
withstanding a pressure of 256 psi are high quality filters and
are recommended as follows:
Oil Filter Part No.
MITSUBISHI Genuine Parts: MD136790
ENGINE OIL FILTER SELECTIONThis vehicle is equipped with a full-flow, throw-away oil filter.
The same type of replacement filter is recommended as a
replacement filter for this vehicle. It is possible, particularly in
cold weather, that this vehicle may develop high oil pressure
for a short duration. You should be sure that any replacement
filter used on this vehicle is a high-quality filter and is capable of
withstanding a pressure of 256 psi (1,765
kpa) (manufacturer’s
specifications) to avoid filter and engine damage. The following
is a highquality filter and is strongly recommended for use on
this vehicle: Mitsubishi Engine Oil Filter P/N MD136790.
Any replacement oil filter should be installed in accordance with
the oil filter manufacturer’s installation instructions.
(1) Remove the engine oil filter by using the oil filter wrench.
(2) Clean the oil filter mounting surface of the oil filter bracket.
(3) Coat engine oil to the O-ring of new oil filter.
(4) Turn the oil filter by hand and install to the filter bracket.
NOTEThe oil filter tightening torque is 14 Nm (11
ft.lbs.1.(5) Start and run engine and check for engine oil leaks.
(6) After stopping engine, check oil level and refill as neces-
sary.
9. MANUAL TRANSAXLE (Inspect oil level)
MOOSBCGInspect each component for evidence of leakage, and check
the oil level by remaining the filler plug. If the oil is contami-
nated, it is necessary to replace it with new oil.
(1) With the vehicle parked at a level place, remove the filler
plug.
-Revision

00-40
GENERAL - Maintenance Service
(2) Check that the transaxle oil level is at the lower portion of
the filler plug hole. For AWD-vehicles, check that the
transfer oil level is at the portion shown in the illustration.
(3) Check to be sure that the transmission oil is not noticeably
‘ddirty, and that it has a suitable viscosity.
10. AUTOMATIC TRANSAXLE
(Inspect fluid level)
MOOSEDL
1.Drive until the fluid temperature reaches the usual tempera-
ture
[70 - 80°C (160 - 18O”F)I.2. Place vehicle on level floor.
3. Move selector lever sequentially to every position to fill
torque converter and hydraulic circuit with fluid, then place
lever in “N” Neutral position. This operation is necessary to
be sure that fluid level check is accurate.
4. Before removing dipstick, wipe all dirt from area around
dipstick. Then take out the dipstick and check the condition
of the fluid.
The transaxle should be overhauled under the following
conditions.
l If there is a “burning” odor.
l If the fluid color has become noticeably blacker.
lIf there is a noticeably great amount of metal particles in
the fluid.
5. Check to see if fluid level is in “HOT” range on dipstick. If
fluid level is low, add ATF until level reaches “HOT” range.
Low fluid level can cause a variety of conditions because it
allows pump to take in air along with fluid. Air trapped in
hydraulic circuit forms bubbles which make fluid spongy.
Therefore, pressures will be erratic.
Improper filling can also raise fluid level too high. When
transaxle has too much fluid, gears churn up foam and
cause same conditions which occur with low fluid level,
resulting in accelerated deterioration of ATF transmission
fluid.
In either case, air bubbles can cause overheating, fluid
oxidation, which can interfere with normal valve, clutch, and
servo operation. Foaming can also result in fluid escaping
from transaxle vent where it may be mistaken for a leak.
6. Be sure to examine fluid on dipstick closely.
L/(Change fluid)
Drain the fluid and check whether there is any evidence of
contamination.
Replenish with new fluid after the cause of any contamination
has been corrected.
(1) Remove drain plug at transaxle case bottom to let fluid
drain.(2) Place a drain container with large opening under the
transaxle oil pan.
(3) Loosen oil pan bolts and tap pan at one corner to break it
loose allowing fluid to drain, then remove oil pan.
d
TSB Revision

00-44
GENERAL - Main Sealant and Adhesive Table
MAIN SEALANT AND ADHESIVE TABLEMWZA- -
ApplicationRecommendedbrand
1. Sealants for engine accessories
(I 1Sealing between rocker
3M ATDcover and camshaft
Part No. 8660
bearing cap
(4G6 DOHC and 6G7or equivalent
engines only)
(2) l Sealing between semi-3M ATD
circular packing and
Part No. 8660
rocker cover and between
semi-circular packing andor equivalent
cylinder head
l Oil pressure switch
(except 4Gl and 6G7engines)
(3) Engine coolanttemperature switch,Engine coolanttemperature sensor,Therm0 valve,Therm0 switch, Joints,Engine coolanttemperature gauge unit(large size)
3M Nut LockingPart No. 4171
or equivalent
(4) Engine coolanttemperature gauge unit(;.s;il size, MD091 0563M ATDPart No. 8660
or equivalent
(5) Oil pan(except 4G5 engine)MITSUBISHI
GENUINE Part No.
MD9971 10or equivalent
2. Sealing between glass and
weatherstrip
(I 1 l Sealing between
tempered glass and
weatherstrip
l Sealing between body
flange and weatherstrip3M ATD
Part No. 8513or equivalent
3M ATD
Part No. 8509or equivalent
(2) Sealing betweenlaminated glass andweatherstrip
3. Adhesion with ribbon sealer
l Waterproof film for doorl Fender panell Splash shieldl Mudguardl Rear combination lamp
3M ATDPart No. 8509
or equivalent
3M ATDPart No. 8625or equivalent
ApplicationRecommended
brand
4. Adhesives for interior trim
(1)Adhesion of polyvinyl-chloride sheet3M Part No.EC-l 368or equivalent
(2)Adhesion of door
3M ATD
weatherstrip to body
Part No. 8001 or3M ATDPart No. 8011or equivalent
(3) Sealing betweengrommet or packing and
metal seal
(4) l Adhesion of headliningand other interior trimmaterialsl Adhesion of fuel tank
to pad
3M ATDPart No.851 3or equivalent3M
Part-No.
EC-l 368
or 3M ATD Part No.
8080 or equivalent
5. Body sealant3M ATDl Sealing of sheet metal,
Part No. 8531 or
drip rail, floor, body side3M ATDpanel, trunk, front panel and
Part No.8646the like jointsl Sealing of tailgate hingesor equivalent
6. Chassis sealant
(I 1 l Sealing of flange surfaces3M ATD
and threaded portions
Part No. 8659l Fuel gauge unit packingor equivalent
(2)Sealing of flange surfaces,3M ATD
threaded portions, packingPart No.8663
and dust cover
l Differential carrier packingor equivalent
l Dust covers for ball jointand linkage
l Steering gear box packing
and shims
l Steering gear housingrack support cover andtop coverl Mating surface of knucklearm flange
(3)Sealing between accelerator
arm bracket and toeboardDrying sealant
(4)Sealant for drum brakeshoe hold-down pin andwheel cylinder3M ATDPart No.851 3or equivalent
TSB Revision1

11-I
ENGINECONTENTS
IMllAA--
CAMSHAFT OIL SEALS....................................
CRANKSHAFT, FLYWHEEL AND
DRIVEPLATE........................................................
CYLINDER BLOCK................................................
CYLINDER HEAD AND VALVE........................
CYLINDER HEAD GASKET................................
ENGINE ASSEMBLY............................................
ENGINE OIL COOLER........................................
GENERAL INFORMATION................................
lbLubricationSystem............................................SectionalView
....................................................
OIL PAN AND OIL PUMP....................................
OIL PAN AND OIL SCREEN................................20
49
5334
23
17
552
3
240
22
PISTON AND CONNECTING ROD....................
ROCKER ARM AND CAMSHAFT....................
SERVICE ADJUSTMENT PROCEDURES........Compression Pressure Check
........................Curb Idle Speed Inspection
............................Drive Belts Tension Adjustment
....................Ignition Timing Adjustment
............................
LashAdjusters
Check........................................Manifold Vacuum
Inspection
.............................
SPECIAL TOOLS....................................................
SPECIFICATIONS................................................General Specifications
....................................
Sealants
.......................................
.....................Service Specifications
....................................
TIMING BELT........................................................
TROUBLESHOOTING........................................44
31
11
15
14
11
13
16
16
84
4
84
26
10

ENGINE - Specifications
/
L
L/
Items
Connecting rod bearing
Oil clearancemm (in.)
Crankshaft main bearing
Oil clearancemm (in.)
Crankshaft
Pin O.D.
mm (in.)
Journal O.D.mm (in.)
Out-of-roundness of journal and pin
mm (in.)
Taper of journal and pin
mm (in.)
End playmm (in.)
Oil pressure at curb idle speed
kPa (psi)
[Conditions: oil temperature is 75 to 90°C
(167 to
194”F)l
Standard value
0.016- 0.046 (.0006- .0018)
0.019 - 0.044 (.0007 - .0017)
49.9 (I ,965)
59.9 (2.358)
Less than 0.003 (.00012)
Less than 0.005 (0002)
0.05 - 0.25 (0020 - .0098)
80 (I 1.4) or more
Limit
0.1
(.004)
0.1 (.004)
0.3 (.012)
Oil pump
Side clearancemm (in.)
Body clearance0.100-0.181 (.0039-.0071)
Side clearance0.040 - 0.095 (.0016 - .0037)
Relief spring
Free lengthmm (in.)43.8 (1.724)
Load
137 N (8.3 Ibs.)]mm (in.)40.1 (1.579)
Drive belt
For alternator (Vehicle without air
conditioner)
Deflectionmm (in.)
Inspection
4.0-5.5(.157-,216)
New belt3.5-4.0(.138-,157)
Used belt4.0-5.0 (.157- ,197)
TensionN (Ibs.)
Inspection350 - 600 (77 - 132)
New belt650
- 850 (143 - 187)
Used belt450
- 600 (99 - 132)
For alternator and air conditioner
compressor
Deflectionmm (in.)
Inspection
4.0-5.5(.157-,216)
New belt3.5-4.0 (1388.157)
Used belt4.0-5.0(.157-,197)
For power steering pump
Deflection
mm (in.)9.0
- 11 .o (354 - ,433)
Timing belt
Amount of projection of auto tensioner3.8-4.5(.149-,177)rodmm (in.)(distance between the tensioner arm andauto tensioner body)
1 TSB Revision

11-8ENGINE - Specifications / Special Tools
SEALANTS
MIKE- -
Items
Oil pan
Oil seal case
Oil pressure switch
Specified sealant
MITSUBISHI GENUINE Part No. MD9971
10 or equivalent
Oil pressure gauge unit
Rocker cover3M ATD Part No.8660 or equivalent
SPECIAL TOOLSMIlDA--
MD998051-01
Loosening and tightening of cylinder head bol
seal installer
compressor
Camshaft oilsealInstallation of camshaft oil seal
1 TSB Revision