1991 MITSUBISHI 3000GT rims

BODY - Quarter Window Glass
42-33
QUARTER WINDOW GLASS
M42LECB
:REMOVAL AND INSTALLATION
Trim (RefertoGROUP52A-Trims.)l Removal and Installation of Center Pillar
Garnish (Refer to GROUP 51 -Garnishes and
18FOOO2
18FO132Removal steps
l * I)*1. Quarter window moulding and glass
2. Packing
3. Window dam
Section A
Adhesive
Cut off nozzle tip
mm (in.)
18FOO6018FO137
Adhesive: 3M SUPER FAST URETHAN 8609 or
equivalent
Primer: 3M SUPER FAST URETHAN PRIMER 8608 or
equivalent
TSB Revision

BODY - Liftgate Glass
LIFTGATE GLASSREMOVAL AND INSTALLATION
42-37
M42LDAO
i
LRemoval steps
I. Defogger connectorl *2. Liftgate moulding upper
3. Liftgate moulding upper clipa*4. Liftgate moulding lower
5. Liftgate moulding lower clip
6. Clip grommet
+* *+ 7. Lift gate glass
8.
Liftgate moulding side
9. window dam
18FO145
Pre-removal and Post-installationOperationl Removal and Installation of Rear Wiper Arm
(Refer to GROUP 51 -Windshield Wiper and Washer
l Removal and Installation of Liftgate UpperTrim (Referto GROUP 52A-Trims.)l Removal and Installation of Liftgate Trim
(Refer to GROUP 52A-Trims.)
l Removal and Installation of Liftgate Side
Trim (Refer to GROUP 52A-Trims )
-ASection A
12-15(.47-.59)
Primer7
Section B27 (1.06)
Cut off nozzle tip
1
,
Adhesive:3M SUPER FAST URETHAN 8609 or equivalentPrimer:3M SUPER FAST URETHAN PRIMER 8608 or equivalent
12 (.47)E!;~;qiffy,8Fo,48,f 7
mm (in.)18FOO6010 t.391TSB Revision
1

51-16
EXTERIOR - Garnishes and Mouldings
GARNISHES AND MOULDINGS
M51RDAFREMOVAL AND INSTALLATION
13 Nm2.5Nm18FO174
Front deck garnish removal steps
1. Wiper arm assembly
2. Front deck garnish
Drip moulding and center pillar garnish removal
steps
Drip line weatherstrip(Refer to GROUP 42
-Door weatherstrip holderDrip Line Weatherstrip.)
3. Drip moulding
Quarter upper trim (Refer to GROUP
52A-Trims.)
4. Center pillar garnish
Adhesive tape:3M ATD Part No. 6382 or equivalentWindshield moulding removal steps
3. Drip moulding
5. Windshield moulding (Refer to
GROUP 42 -Windshield.)
Liftgate moulding removal
6.
Liftgate moulding (Refer to
GROUP 42 - Liftgate Glass.)
Quarter window moulding and glass
removal steps
4. Center pillar garnish
7. Quarter window moulding and
glass (Refer to GROUP42
-Quarter Window Glass.)
Side garnish removal
l * l *8. Sidegarnish
Rear panel garnish removal steps
Rear end trim
Rear side trim
3(Refer to GROUP
52A-Trims.)9. Rear combination light
10. Rear panel garnish
I
I
I
I
I1
~
:Ij ~
I
I1
I
I
L.JTSB Revision

51-20EXTERIOR - Aero Parts
AERO PARTSM5lXAA.J
REMOVAL AND INSTALLATION
25NmI:8 ft.lbs.
18FO179
@ Adhesive tape:3M ATD Part No. 6382 or equivalent
m Adhesive:3M ATD Part No. 8609 SUPER FASTURETHAN or equivalent
18FO251Side air dam removal steps
Front splash shield (Refer to GROUP 42
-Fender.)
Quarter trim (Refer to GROUP
52A-Trims.)
l * **1. Side air dam
Rear spoiler removal steps
Liftgate lower trim (Refer to GROUP 52A-Trims.)
2. Rear spoiler assembly
3. Center stay
4. High mounted stop light
TSB Revision

EXTERIOR - Aero Parts51-21
8
Side air dam removal steps
Front splash shield
(Refer to GROUP 42
- Fender.)
+I) l +1. Side airdamRear spoiler removal steps
Liftgate lower trim
(Refer to GROUP 52A-Trims.)2. Rear spoiler assembly
4. High mounted stop light
Front under cover panel, air dam link assembly
removal steps
5. Side cover panel
(L.H.)6. Front cover panel
7. Center cover panel
8. Front under cover panel
9. Lower plate
10. Upper plateI)* 11. Air dam link assembly
12. Under cover bracket
16FO252
16FOO53Active aero switch removal steps
13. Switch garnish C
14. Active aero switch
Active aero control unit removal steps
Rear side trim
(L.H.)(Refer to GROUP 52A-Trims.)15. Active exhaust control unit
16. Active aero control unitTSB Revision

EXTERIOR - Rear Wber and Washer51-35
REAR WIPER AND WASHERM51 KKAO
,/REMOVAL AND INSTALLATION
16FO104.lO
.llRemoval steps of wiper motor
1. Wiper blade
l *2. Wiper arm
3. SpacerRemoval steps of washer tube
Front pillar trim
(RH)Quarter trim (RH)
Liftgate lower trim (Refer to GROUP 52A -Quarter upper trim
(RH)Rear roof rail trim!R$$f$$ GRoUP 52A
Trims.)Rear side trim
(RH)i .
4. Wiper motor
l *8. Liftgate moulding, upper
9. Washer nozzle
Removal steps of washer tank
Rear end trim (Refer to GROUP
52A-Trims.)5. Cap
6. Washer tank
7. Washer motor
10. Tube and grommet assembly
11. Washer tube
1 TSB Revision

EXTERIOR - Rear Wiper and Washer
51-3718N007F
jINTERMITTENT WIPER RELAY
(1) Remove the quarter trim. (Refer to GROUP 52A
- Trims.)
(2) With the intermittent wiper relay connected to the wiring
harness connector, let the wiper operate intermittently and
check the voltage at terminal
0.WASHER MOTOR
(1) When the washer motor is inspected, make sure that it is
mounted on the washer tank and that the washer tank is
filled with water.
(2) Connect the battery as shown to check whether water is
pumped out.
SERVICE POINT OF INSTALLATION
2. INSTALLATION OF WIPER ARM
After assembling the wiper blade to the wiper arm, install
the wiper arm with its tip positioned along the ceramic part.
TSB Revision

INTERIORCONTENTSNWAA-A~
FLOOR CONSOLE*
____....._.........__._..._......_..._...... 11
REAR SEAT . .._._____..______....____.._.._._..___.._._____.....___....24
FRONT SEAT*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18SEAT BELT*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25IHEADLINING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17TRIMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12INSTRUMENT PANEL*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . .
i
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components, (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
2I