1991 MITSUBISHI 3000GT engine

13-164CRUISE CONTROL SYSTEM - Troubleshooting
2Inspection of control switch circuit
IGNITIONSWITCHtACC)
*X35-AK-R1302r-
._--------
LE- @CONTROL UNIT
TROUBLESHOOTING HINTSECU terminal voltage
DESCRIPTION OF OPERATIONdThe control switch is a switch in which the SET,
RESUME and CANCEL switches are integrated.
Therefore, different resistance values are used for
the individual switches to change the outputs
(voltages) to the control unit. Current flows through
fuse No. @ of J/B and through the control switch to
the control unit.
1. SET switchWhen the cruise control switch is ON, if the SET
switch is set to ON while vehicle speed is within
a range from about 40 to 145 km/h (25 to 90
mph), the vehicle starts cruising at the speed. If
the SET switch is kept at ON during cruise
operation, the vehicle coasts, and starts cruising
at the speed reached when the SET switch is
set to OFF.
2. RESUME switch
Even if cruise operation is canceled, the vehicle
resumes cruising at the speed set before the
cancellation. Both when the main switch is set
to OFF and when the vehicle speed is reduced
to less than 40 km/h (25 mph) , the vehicle will
not resume cruising at the previously set speed
even if the RESUME switch is set to ON. If the
RESUME switch is kept at ON during cruise
LJoperation, the engine accelerates, and the vehi-
cle starts cruising at the speed reached when
the RESUME switch was set to OFF. (However,
when the vehicle speed is raised to more than
145 km/h (90 mph), the vehicle cruises at
approximately 145 km/h {90 mph).
3. CANCEL switch
When the CANCEL switch is set to ON during
cruise operation, the cancel signal is input to the
control unit which internally interrupts the power
supply to the vacuum pump assembly for
cancellation of cruise operation.
18Control switchSignal name
L
Condition
I
Terminalvoltage1
When all switches are OFFIov1
When SET switch is ONI3vI
When RESUME switch is ON
When CANCEL switch is ON6Vd
Systemvoltage
TSB RevisionJ

CRUISE CONTROL SYSTEM - Troubleshooting13-169
8Inspection of inhibitor switch circuit
LDESCRIPTION OF OPERATIONThe inhibitor switch is interlocked with the starter
switch. When the gear selector lever is placed in the
“N” position during vehicle speed control, a cancel
signal is input to the control unit which internally
interrupts the power supply to the vacuum pump
assembly drive circuit for cancellation of vehicle
>
%
‘18@
INHIBITOR
SWITCHspeed.TROUBLESHOOTING HINTSECU terminal voltage
Terminal
Signal nameConditionTerminal
No.voltage
1Inhibitor switchInhibitor switch inov
“N” or “P” position
System
voltage
STARTER=
L;RX%-AK-R1907
9Inspection of throttle position sensor circuit
ENGINE
CONTROL
UNIT
:l:DOHC
*-OFF 01
w2,3' /% *
THROTTLE;;f&;iON
{ml@
CRUISE CONTROL UNITKX.95~AC-R1308
DESCRIPTION OF OPERATIONThe throttle position sensor (with built-in idle switch)
is used for engine control as well as cruise control.
The throttle position sensor sends data to the
control unit, regarding the opening of the accelera-
tor. The idle switch inputs the data to the control
unit on whether or not the accelerator pedal is
operated.
TROUBLESHOOTING HINTSDiagnosis No. 17 (Not automatically canceled)
ECU terminal voltage
Signal nameConditionTerminal
voltageIdle switchWhen accelerator OV
pedal is depressed
When accelerator 4.5
- 5.5V
pedal is not de-
pressed
Throttle position During idle0.48
-sensor0.72V
When fully opened 4.0
- 5.5V
TSB Revision

13-176CRUISE CONTROL SYSTEM - Troubleshooting
HARNESS AND COMPONENTS LAYOUT
ENGINE COMPARTMENT
01 Jumper connector
02 Vacuum pump
03 Throttle position sensor04 Inhibitor switch
05
VeTkFo;peed sensor
INSTRUMENT PANEL
AND FLOOR CONSOLE
Combination meter
Main switchEngine front view
03
36FOOO5Engine rear view
16FO175
36FOO17
TSB Revision

13-I 78CRUISE CONTROL SYSTEM - Service Adjustment ProceduresSERVICE
ADJUSTMENT PROCEDURESCRUISE CONTROL CABLES INSPECTION AND ADJUSTMENT
I
MlSFTCA
‘\J ~
Cruise control actuator
Cruise control assemblyAdjusting nut A
Link B
.
Adillstinn nr~+ R\Cruise control
cable
Adjusting nut C
Accelerator cable
Throttle valve-Link A
07N0004(1) Set the air conditioner, lights and other switches to OFF for
inspection at no load.
(2) Let the engine warm up until it runs at idle.
(3) Check that the idle speed is within the specified range.
(4) Stop the engine and set the ignition switch to OFF.
(5) Check that the accelerator cable, cruise control cable and
throttle cable are routed without sharp bends.
(6) Depress the accelerator pedal to check that the throttle
lever moves smoothly from the fully-closed to fully-opened
position.
(7) Check the free travel state of the inner cables of the
accelerator cable, cruise control cable and throttle cable.
(8) If the inner cables are too loose or have no free travel at all,
check using the following procedure.@ Remove the’ link protector.
@ Loosen the adjusting and lock nuts of the throttle lever
and intermediate links A, B and C to place the throttle
lever and intermediate links A, B and C in the free state.
1 TSB Revision

CRUISE CONTROL SYSTEM - Service Adjustment Procedures13-179Adjusting nut C
07NOOlELink Blever
07N0019Link
B07NOOlE
y,jj--ww ,03LO122
\\ \18FO2.2'@ Set the ignition switch to ON (do not start the engine).@ Rotate intermediate link C in the direction shown until it
is blocked by the stopper, turn down adjusting nut C in
the direction that the free travel of the inner cable is
reduced, and back off adjusting nut C the specified
number of turns just before intermediate link C begins
to move.
Amount adjusting nut C is to be backed off:
About l/2 turn [inner cable free travel0
- 1 mm (0 - .04 in.)]
About two turns [inner cable free
travel 2 to 3 mm
(.08 to .12 in.)]@ Secure the accelerator cable with the lock nut.@ Turn down adjusting nut B in the direction that the free
travel of the inner cable of the throttle cable is reduced.
At the position where the lever of intermediate link B is
brought into contact with intermediate. link C, back off
adjusting nut B the specified number of turns.
Amount adjusting nut B is to be backed off:
About one turn [inner cable free travel 1 to 2 mm
(.04 to .08 in.)]@ Secure the throttle cable with the lock nut.@ Secure the adjusting bolt of the surge tank.@ Turn down adjusting nut A in the direction that the free
travel of the inner cable of the cruise control cable is
reduced. At the position where the lever of intermedi-
ate link A is brought into contact with intermediate link
B, back off adjusting nut A the specified number of
turns.
Amount adjusting nut A is to be backed off:
About one turn [inner cable free travel 1 to 2 mm
(.04 to .08 in.)]@ Secure the cruise control cable with the lock nut.@ After adjustment, check to see that the end of the fixed
SAS is in contact with the stopper of the throttle lever.
CRUISE CONTROL SYSTEM INSPECTION
MlBFlDA
CRUISE CONTROL MAIN SWITCH CHECK
(1) Turn the ignition key to ON.
(2) Check to be sure that the CRUISE CONTROL ON indicator
light within the combination meter illuminates when the
main switch is switched ON.
TSB Revision

COOLINGCONTENTS
M14AA..
ENGINE COOLANT TEMPERATURE GAUGE
UNIT, ENGINE COOLANT TEMPERATURESENSOR AND ENGINE COOLANT
TEMPERATURE SWITCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._.__15
RADIATOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
SERVICE ADJUSTMENT PROCEDURES . . . . . . . .7Cap Pressure Test
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._.......7Engine Coolant Concentration Test
. . . . . . . . . . . . . . . .‘7
L,Engine Coolant Leak Check
. . . . . . . . . . . . . . . . . . . . . . . . . . . .7Engine Coolant Replacement
. . . . . . . . . . . . . . . . . . . . . . . .7
SPECIFICATIONS. . . . . . . . . . . . .._.................................General Specifications
. ..___....___._...___.__............Lubricant
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._.................._........Sealant and Adhesive
. . . . . . . . . . . . . . . . .._...........Service Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . .
THERMOSTAT. . . ..__......................_.._...................
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._...No Rise in Temperature
Overheat
WATER PUMP, WATER PIPE AND WATER
HOSE. . . . _......_........_ _.._ .._..... . . . . . . . . . . . ._. . . . . . . . . . . . . . . . .
2
2
2
3
2
11
3
13

14-2COOLING - SDecifications
SPECIFICATIONSGENERAL SPECIFICATIONSMMCA..
Items
Cooling method
Radiator
Type
Radiator fan motor
Type
Water pump
Type
Thermostat
Type
Identification markSpecifications
Water-cooled, pressurized, forced circulationwith electrical fan
Pressurized corrugated fin type
Direct current ferrite type
Centrifugal impeller type
Wax type with jiggle valve
76.5 (Stamped on flange)
dSERVICE SPECIFICATIONS
Items
Standard valueSpecifications
Range of coolant antifreeze concentration%30-60
Thermostat
Valve opening temperature of thermostat
“C (“F)
Full-opening temperature of thermostat“C (“F)
Opening pressure of cap high pressure valvekPa (psi)
Therm0 sensor (on radiator) operating temperature

OFF-t ON“C (“F)
ON -+ OFF“C (“F) condenser fan-Vehicles with air conditioner>
OFF-ON“C (“F)
ON + OFF“C (“F)
Limit
76.5 (170)
90
(I 94) or more
75-105(11-15)81-89
(178- 192)77(171)orless
91-99
(196-210.)
87 (189) or less
Opening pressure cap high pressure valve
kPa (psi)65 (9.2)LUBRICANT
MlQCD- -
ItemSpecified lubricantQuantity
Engine coolantlit. (qts.)High quality ethylene glycol8.0 (8.5).
antifreeze coolant
‘d
TSB Revision

COOLING - Specifications / Troubleshooting
SEALANT AND ADHESIVE14-3
MMCE- -
/
id
ItemsSpecified sealants and adhesive/
Engine coolant temperature gauge unit
Engine coolant temperature sensor (Engine control)
Engine coolant temperature sensor (Air conditioner)3M Nut Locking Part No. 4171
TROUBLESHOOTING
L
MllEAAL
Symptom
OverheatProbable cause
Insufficient engine coolant
Too high an anti-freeze concentration
Inoperative electric cooling fan
Faulty thermosensor
Faulty electrical motor
Faulty radiator fan relayRemedy
Replenish
Correct anti-freeze concentration
Replace
Damaged or blocked (insufficiently ventilated)
radiator finsCorrect
Water leaks
Damaged radiator core joint
Corroded or cracked hoses
(radiator hose, heater hose, etc.)
Faulty cap valve or setting of spring
Cracked thermostat housing
Loose water pump mounting bolt or leaking
gasket
Replace
Loose bolt or leaking gasket in water outlet
I
Correct or replacefitting
Loose bolt or leaking gasket in water inletfitting
Loose thermostat housing bolts or leakingfrom gasket
Retorque bolts or replace gasket
Faulty automatic transaxle oil cooler operation
Blocked or collapsed hose and pipeReplace
Loose hose and pipe connectionCorrect
Faulty thermostat operationReplace
Faulty water pump operationReplace
Water passage clogged with slime or rust depositClean
or foreign substance
No rise in temperature
Faulty thermostatReplace
( TSB Revision