1991 MITSUBISHI 3000GT instrument panel

35-32SERVICE BRAKES -AniLlock Braking System Troubleshooting
NoWith the ignition key in the “ON” posi-
I--Check fuse No. 11. If it is
blown, correct the cause of
the blown fuse and then
replace the fuse.J
Yes
I
( ~;T&$Efg,?~ )harness connector terminal
No. 59 and ground indicate
battery voltage?
----F--
&Repair harness.
Circuit in combination meter
-is broken.
Is there continuity between combination
meter No. 58 and No. 59 terminals?
Are instrument panel wiring harness
and body wiring harness connected
Broken wire in ECU, valve relay or both
drive circuits. Check both circuits.
TSB Revision

STEERING - Steering Wheel and Shaft37A-13
STEERING WHEEL AND SHAFTM37GA- -
L
REMOVAL AND INSTALLATION
Post-installation Operation
l Checking of Steering Wheel Positlonwith Wheels Straight Ahead
\5Nm
4 ft.lbs.I7
12 Nn8ft.lb
\1
40 Nm
29 ftlbs.
i
13FOO35Removal steps
/
L
Mb1. Air bag module*I) l a2. Steering wheel
3. Lower column cover;: E;feTn switch assembly
4. Upper column cover9. Key interlock cable
I
(Refer to GROUP 23 -
5. Knee protectorIO. Slide leverTransaxle Control.)
(Refer to GROUP
52A- Instrument Panel.)11. Steering column assembly
6. Lap cooler duct and foot shower duct12. Column support assemblyTSB Revision

L
/
idBODY
- Power Window
REMOVAL AND INSTALLATION42-51
Cll Door Wlndow Glass Adjustment
18FO205
18FO198Door window regulator assembly removal steps
Door trim (Refer to
P.4241.)Waterproof film (Refer to P.42-41.)1. Delta cover inner
2. Delta cover outer
18FO1996. Delta sash
7. Door window glass
8. Door window regulator assembly
9. Door glass guide track front
10. Door glass guide track rear
Door belt line outer weatherstrip (Refer to
P.42-65.)3. up stop
4. Stabilizer inner frontPower window switch assembly removal steps
Door trim (Refer to P.42-41.)11. Power window switch assembly
5. Stabilizer inner rear
INSPECTION
POWER WINDOW RELAY
(1) Remove .the knee protector assembly.
(Refer to GROUP 52A
- Instrument Panel.)
ow relay from indoorrelaybox.

BODY - Central Door Lockina Svstem42-63
:Vehicles with power window>
Dower window main switch side
Power window sub switch side
18FO107DOOR LOCK SWITCH
Check for continuity in accordance to the following connection
table.
Power window main switch side
LOCKIo--+--Q I
UNLOCKII c-+---oL
NOTEO-O indicates that there is continuity between the terminals
Power window sub switch side
1 LOCKIo---+-o I
OFFII
I
1 UNLOCKI c--+--
NOTEO-O indicates that there is continuity between the terminals.

LOCK00
OFF
UNLOCK00
NOTEO-O indicates that there is continuity between the terminals.
DOOR LOCK RELAY
(1) Remove the knee protector assembly:
(Refer to GROUP 52A
- Instrument Panel.)
(2) Remove the door lock relay from indoor relay box.
TSB Revision

EXTERIOR - Windshield Wiper and Washer51-33
L
lj
Inspection of Operation
Low-speed High-speedoperationoperation1610026
Inspection of Stop Posltion
n
16NOO25
16FO200
ITSB ISERVICE POINT OF REMOVAL
6. REMOVAL OF WIPER MOTOR
(1) Remove the wiper motor mounting bolts.
(2) Using a plain screwdriver, detach the crank arm of the
wiper motor from the linkage to remove the wiper
motor.
Caution
Do not remove the crank arm from the wiper motor
except when necessary, as the auto stop angle has
been preset. When the crank arm is to be removed,
make a mark on both of them before removal.
INSPECTION
INSPECTION OF WIPER MOTOR
Inspect the wiper motor mounted on the vehicle with its
connector disconnected.
Inspection of Wiper Motor Operation at LOW and HIGH
Speeds
Connect the battery to the wiper motor as shown, and check its
operation at LOW and HIGH speeds.
Inspection of Wiper Motor STOP Position
(1) Operate the wiper motor at LOW speed and intermediately
disconnect the battery to let the wiper motor stop.
(2) Connect the terminals as well as the battery, as shown, and
check that the wiper motor stops at the automatically-
stopped position following LOW-speed operation.
INSPECTION OF COLUMN SWITCH
(1) Remove the knee protector.
(Refer to GROUP 52A
- Instrument Panel.)
(2) Remove the column cover.
(3) Remove the column switch right coupling connector
(11terminals).
Inspection of Wiper and Washer Switch
Operate the switch to check for continuity between the
terminals.
345678
Variable intermittent wiper
control switch
Washer switch
NOTEC-0 denotes that there is continuity between the terminals.
‘vision

51-38EXTERIOR - Door Mirror
DOOR MIRRORREMOVAL AND INSTALLATION~MSlGAAR
I18FO166
Door mirror removal steps
l *I. Door mirror
2. Harness connector
a*3. Mirror
Electric remote controlled mirror switch removal
4. Instrument panel switch
5. Electric remote controlled mirror switch
Pivnt
NotchesSERVICE POINTS OF REMOVAL
1. REMOVAL OF DOOR MIRROR
Tilt the door mirror backward and forward to remove the
attaching bolts.
3. REMOVAL OF MIRROR
Tilt the mirror upward and fit a screwdriver blade covered
with protective tape in the notch between the mirror and
the pivot plate to pry up the mirror.
Caution
Do not fit the screwdriver blade between the pivot
plate and actuator assembly.
\
LjTSB Revision

INTERIORCONTENTSNWAA-A~
FLOOR CONSOLE*
____....._.........__._..._......_..._...... 11
REAR SEAT . .._._____..______....____.._.._._..___.._._____.....___....24
FRONT SEAT*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18SEAT BELT*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25IHEADLINING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17TRIMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12INSTRUMENT PANEL*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . .
i
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components, (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
2I

52A-8INTERIOR - Instrument Panel
INSTRUMENT PANELM52UAAT
For installation of the instrument panel, the bolts and screws described below are used. They are indicated by
symbols in the illustration.
,4x
16(.I6x.63)
5x16(.20x.63)4x
12(.I6x.47)
6x16(.24x.63)
II6 x 25 (.24 x .98)19N0001I
NOTED = Thread diameter
L = Effective thread length
TSB Revision
1