Page 721 of 906

SCHEDULED SERVICES 
Article Text (p. 38)
1990 Volkswagen Corrado
For Volkswagen Technical Site:  http://vw.belcom.ru    
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000  09:50PM³   ³  Door/Hood/Trunk Stops, Hinges & Locks                         ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Check Body Drain Holes                                        ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Check Automatic Seat Belt Operation (1990-94)                 ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Check Seat Belt Webbing and Release Mechanisms                ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Windshield Washer System                                      ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Parking Brake Adjustment                                      ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Check Clutch Adjustment                                       ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Suspension & Wheel Bearings                                   ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Check Shift Interlock Operation                               ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Inspect Steering Linkage/Front Suspension                     ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Lubricate Chassis                                             ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Inspect Brake Pads, Rotors and Calipers                       ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Inspect Brake System Hoses & Lines                            ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Inspect Shocks/Struts for Leakage                             ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Inspect Tire Wear and Condition                               ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Rotate Tires and Adjust Air Pressure (Including Spare)        ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Road Test                                                     ³
ÃÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³      Replace                                                       
³
ÃÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Engine Oil                                                    ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Oil Filter                                                    ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Spark Plugs                                                   ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Air Filter Element                                            ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Replace Passenger HVAC Air Filter (1995)                      ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Replace Automatic Transmission Fluid and Clean ATF Strainer   ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Camshaft Timing Belt (2.0L Only)                              ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³   
³  Oxygen Sensor                                                 ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ 
     
        
        Page 776 of 906

TRANSMISSION SERVICING - M/T 
Article Text (p. 7)
1990 Volkswagen Corrado
For Volkswagen Technical Site:  http://vw.belcom.ru    
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000  09:52PM
         VANAGON (4-SPEED)
         1) Place gearshift lever in Neutral position. Align round
centering holes of upper gearshift lever housing plate with holes in
lower lever bearing plate.
         2) Loosen nut on clamp that connects front and rear shift
rods. Ensure joints of shift rods slide freely. Remove spare tire. Set
shift lever on transaxle in vertical Neutral position.
         3) At gearshift lever end of front shift rod, ensure stop
finger of front shift rod is in center of shift mechanism housing.
         4) Adjust front shift rod end so there is 29/32" (23 mm)
clearance between front shift rod end and stop plate. Tighten shift
rod clamp.
         5) Check for proper operation. Ensure shift lever does not
rub against heater pipe insulation.
         VANAGON (5-SPEED SYNCRO)
         1) Place gearshift lever in Neutral position. Align round
centering holes of upper gearshift lever housing plate with holes in
lower lever bearing plate.
         2) Loosen nut on clamp that connects front and rear shift
rods. Ensure joints of shift rods slide freely. Remove skid plate.
Place shift lever on transaxle in vertical Neutral position.
         3) Measure distance between reverse gear lock and stop shift
rod. Clearance should be 29/32" (23 mm). Tighten clamp in this
position. Ensure all gears engage without jamming. Check reverse
lockout operation. With transmission in 1st gear, measure distance
between gear shift lever and heater covering. Clearance should be
19/32" (15 mm).
END OF ARTICLE 
     
        
        Page 883 of 906

WHEEL ALIGNMENT THEORY/OPERATION 
Article Text
1990 Volkswagen Corrado
For Volkswagen Technical Site:  http://vw.belcom.ru    
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000  09:53PM
ARTICLE BEGINNING
         GENERAL INFORMATION
         Wheel Alignment Theory & Operation
         ALL MODELS
         * PLEASE READ THIS FIRST *
NOTE:    This article is intended for general information purposes
         only. This information may not apply to all makes and models.
         PRE-ALIGNMENT INSTRUCTIONS
         GENERAL ALIGNMENT CHECKS
         Before adjusting wheel alignment, check the following:
      *  Each axle uses tires of same construction and tread style,
         equal in tread wear and overall diameter. Verify that radial
         and axial runout is not excessive. Inflation should be at
         manufacturer's specifications.
      *  Steering linkage and suspension must not have excessive play.
         Check for wear in tie rod ends and ball joints. Springs must
         not be sagging. Control arm and strut rod bushings must not
         have excessive play. See Fig. 1.Fig. 1:  Checking Steering Linkage
      *  Vehicle must be on level floor with full fuel tank, no
         passenger load, spare tire in place and no load in trunk.
         Bounce front and rear end of vehicle several times. Confirm
         vehicle is at normal riding height. 
     
        
          
   
    
    Page:  
    < prev   1-8  9-16   17-24