1990 MITSUBISHI SPYDER check engine light

ENGINE AND EMISSION CONTROL Auto-cruise Control’
Code 2 Vehicle speed signal system
[Comment]l Malfunction of the vehicle This diagnostic trouble code is output if the vehic le speed signals from the vehicle speed sensor l of connectorare not input to the auto-cruise control-ECU when t he vehicle speed is 40 km/h (25 mph) l
Malfunction of the harness
or more. l Malfunction of the auto-cruise
Check the vehicle speed sen(Refer to GROUP 54 CombinationMeter.)
1. NG
Measure at the vehicle speed sensor connector Check the following connector. l Disconnect the connector, and measure at the
harness side.O K
1. Voltage between 1 and ground (Ignition switch: ON)
NG
System voltage
2.Voltage between 3 and ground2. N G(Ignition switch: ON)
OK: 4.6 5.2 3.Continuity between 2 and ground3. N G
OK: Continuity
OK
Check trouble symptom.
N G
Check the harness between the speed sensor
Check the following
OKNG
Check trouble symptom.
NG
Check the harness between the auto-cruise ECU and the vehicle soeed sensor connector.
OKNG
Replace the auto-cruise control-ECU.
and ignition switch connector
OK
Check the ignition switch.
(Refer to GROUP 54 , ,
Check the harness between the vehicle speed sensorand the ground. Repair, if necessary.
Code Autocruise vacuum pump power supply systemProbable cause
[Comment]
This code will be output when the drive signals for the auto-cruise vacuum pump release valve,
control valve and motor are not input to the auto-c ruise control-ECU.l
the stop light l
Malfunction of the connector
l
l of the auto-cruise
at the auto-cruise vacuum
l Disconnect the connector and
l Voltage between terminal (1) and
OKN G Check the harness between the cruise vacuum pump and the cruise control-ECU.
and
Replace the auto-cruise control-ECU.
TSB Revision

ENGINE AND EMISSION System
.,
INSPECTION PROCEDURE 3
Input switch inspection using the scan tool is pdssible.
(However, diagnostic inspection is possible.)
I
[Comment]A malfunction of auto-cruise control switch circuit system may be present.l
Malfunction of the auto-cruise control l Malfunction of the clock spring .
l of the connector.
l Malfunction of the harness.
.
NG
(Refer to
Measure at clock spring connector
l sure at the harness side
l Voltage between terminal (2) and
groundOK: Battery positive voltage
OK
Check trouble symptom.
C h e c k t r o u b l e spring and auto-cruise
INSPECTION PROCEDURE 4
When brake pedal is depressed, auto-cruise control does not
cancel.Probable , ,
[Comment]A malfunction of stop light switch or a malfunction of stop light circuit may be present.l
Malfunction of the stop light switch.
l Malfunction of the connector.
l Malfunction of. the
l Malfunction of the auto-cruise control-ECU.
Does stop
illuminate?
No
Replace the auto-cruise control-ECU.
lDisconnect the connector and mea-sure at the harness side.
Check trouble symptom.Check the following connectors:
TSB Revision

ENGINE AND EMISSION CONTROL Auto-cruise
INSPECTION PROCEDURE 11
When the auto-cruise control main switch is ON, the switch
indicator on the instrument panel does not illumina te.
(However, auto-cruise control is normal.) Probable cause
[Comment]l auto-cruise control main
Blown bulb in auto-cruise control main switch.switch.
Replace the auto-cruise control main switch.
INSPECTION PROCEDURE 12
Auto-cruise control main switch illumination light does not
illuminate. Probable cause
[Comment]A malfunction of auto-cruise control main switch, h
arness, or connector may exist.l
Malfunction of the auto-cruise control main
switch. Malfunction of the connector.
l Malfunction of the harness.
(Refer to
Measure at auto-cruise control main
switch connector
lDisconnect the connector and mea-sure at the harness side.
l Voltage between terminal (2) and
groundOK: Battery positive voltage
NG
Check trouble symptom.
TSB Revision

ENGINE AND EMISSION CONTROL Auto-cruise Control
INSPECTION PROCEDURE 13
Auto-cruise control indicator inside combination meter does
not illuminate. (However, auto-cruise control is no rmal.)Probable cause
[Comment]A malfunction of the bulb, the connector harness may be present. l
Malfunction of the bulb.
l Malfunction of the harness. Malfunction of the connector.
l Malfunction of the auto-cruise control-ECU.
to
illuminate when terminal (23) of
Check trouble symptom.
Replace the auto-cruise control-ECU. Check the harness between the
combination meter and auto-cruise
control-ECU.
if
INSPECTION PROCEDURE 14
Stop light switch input circuit system check (Code No. 23)II
Stoplight switch check (Refer to
Check the harness between jumper connector and
auto-cruise control-ECU. Repair, if necessary.
INSPECTION PROCEDURE 15 C l u t c h p e d a l p o s i t i o n s w i t c h
or p o s i t i o n s w i t c h i n p u t c i r c u i t s y s t e m c h e c k
( C o d e N o . 2 6 )

Check trouble symptom.
OK
NG
Check the harness between clutch pedal position swi tch and
auto-cruise control-ECU. Repair, if necessary.
Park/neutral position switch check (Refer to
Starter relay continuity check
(Refer to GROUP 16 Starting System.)
57
Check trouble symptom. Check the harness between auto-cruise control-ECU and power
TSB Revision

ENGINE AND EMISSION CONTROL Auto-cruise Control System
Adjusting nut(C)
c o n t r o l - - - - - -
ON
AUTO-CRUISE CONTROL (Turbo)
and
Engine>
1.Adjust with the adjusting nut so when the lever stopper
hits the link B, the auto-cruise control cable play (inner
cable play) reaches the standard value.
Standard value:
mm in.)
2. Fix the auto-cruise control cable with the lock nut.
SPEED CONTROL CABLE
Engine
Hold the link at the position where the lever touches
the link B. Then fix the speed control cable.
AUTO-CRUISE CONTROL SYSTEM
OPERATION CHECK
17200160048
AUTO-CRUISE CONTROL MAIN SWITCH INDICATOR
LIGHT
1. Turn the ignition key to ON
2.Check that the indicator within the switch illumina tes when
the main switch is switched ON.
AUTO-CRUISE CONTROL
1. Switch ON the main switch.
2. Drive at the desired speed within the range of approximately
km/h mph) Engine
(Non-turbo)>,
km/h (25-124 mph) Engine
(Turbo) and
Engine>.
3. Switch ON the SET switch.
4. Check to be sure that when the switch is release d the
speed is the desired constant speed,
.
NOTE
‘If the vehicles speed decreases to approximately 1 5 km/h
(9 mph) below the set speed because of climbing a h ill
for example, the auto-cruise-‘control will be cance led.
TSB Revision

Engine and
VACUUM CIRCUIT DIAGRAM
Engine (Turbo)>intake air
Throttle bodyL: Light Blue
Red
B: Black
G: Green YellowW: WhiteTo combustion
chamber
Check
EVAP(ON: open)
EVAP canister
TSB Revision
Air
Turbocharger wastegateTurbochargerwasteate solenoid
ON: open)

(Turbo) and
Engine (Turbo)>
Thin stick(Extremely light)
Vacuum side
Thin stick
PCV valve
POSITIVE VENTILATION VALVE”
CHECK
Hold the PCV valve with the vacuum side
Using light pressure depress the PCV valve spring
the thin stick mm. Release pressure on stick
to see if the PCV valve spring will lift
stick to its
original position.
2.If the stick returns quickly to its original positi on,
valve is OK. If the stick does not return quickly, Clean
or replace the PCV valve.
TSB Revision

17-70 CONTROL (Turbo) and Engine>
PURGE CONTROL SYSTEM CHECK (PURGE FLOW CHECK)
ENGINE (TURBO)>
Intake manifold plenum
EVAP purgesolenoid(ON: OPEN)
Nipple
Purgecontrolvalve
Check valve Air cleaner
Air intake hose
Purge flow
indicator
700)
1.Disconnect the purge hose from the evaporative emis sion
(EVAP) canister, and connect the special tool (purg e flow
indicator) between the EVAP canister and the purge hose.
2. The vehicle should be prepared as follows before the
inspection and adjustment.
lEngine coolant temperature: F)
l Lights, cooling fan and accessories: OFF
l Transaxle: Neutral (A/T for
range)
3. Run the engine at idle for 3 minutes or more.
Revision