1987 MAZDA 626 ignition

TROUBLESHOOTING WITH SST 4B
CODE NUMBER
Malfunction display
Self-diagnosis Fail-safe Code
No. Output signal pattern subsystem Self-diagnosis Fail-safe

01
ON
OFF

Ignition pulse
No ignition signal
08
Air flow meter
Open
or
short circuit
Maintains basic sig-
nal
at
preset value
09
1 111

Water thermo sensor
Open
or
short circuit
Maintains constant command 35°C (95 °F)
10
Intake
air
thermo sensor (air flow meter) Open
or
short circuit
Maintains constant 20°C (68°F) command
12
£_IUILJIIL

Throttle sensor
Open
or
short circuit
Maintains constant
command
of
throttle
valve fully open
14
OFF
TL
I I nil

Atmospheric pres-
sure sensor Open
or
short circuit
Maintains constant command
of
sea level pressure
15
oTp m 11 [U

Oxygen sensor Sensor output con-tinues less than 0.55V 120 sec. after engine starts (1,500 rpm)
Cancels EG
I
feed-
back operation
17
SLJlMJl

Feedback system Sensor output
not
changed
20
sec.
af-
ter engine exceeds 1,500 rpm
Cancels EGI feed-back operation
25
^JMLJl

Solenoid valve (pres-
sure regulator)
Open
or
short circuit
26
SUUBUIL

Solenoid valve (purge control)
Open
or
short circuit 28
£ mi in nr

Solenoid valve
(EGR) Open
or
short circuit
34
^jmiUTT

Air bypass solenoid
valve (Idle-up
C)

Open
or
short circuit
35
0Nnnnj OFFU u UUU
"fin nnr
Air bypass solenoid
valve (Idle-up
B)

Open
or
short circuit

76G04B-008
Caution
a) If there is more than one failure present, the lowest number malfunction code is dis-
played first, the remaining codes are displayed sequentially.
b) After repairing a failure, turn off the ignition switch and disconnect the negative battery
cable and depress the brake pedal for at least 2 seconds to erase the memory of a mal-
function code.
4B-13

4B TROUBLESHOOTING WITH SST
If a malfunction code number is shown on the SST, check the following chart along with the wiring
diagram.
Code No. 01 (Ignition pulse) PC: Possible Cause
76G04B-009
4B—14

SWITCH MONITOR FUNCTION 4B
SWITCH MONITOR FUNCTION
Individual switches can be monitored by the SST.
Note
The test connector must be grounded and the ignition switch ON (engine stopped).
Control unit
76G04B-022
Switch Self-Diagnosis Checker (Monitor lamp) Remarks Switch Light ON Light OFF Remarks

Clutch switch Pedal released Pedal depressed Gear:
IN

Neutral switch In gear Neutral Clutch pedal released
Idle switch Pedal depressed Pedal released
—

Brake light switch Pedal depressed Pedal released
—

A/C switch ON OFF Blower motor position:
"1"

position
Headlight switch ON OFF
—

Rear defroster switch ON OFF
—

Blower switch ON OFF Blower motor position:
"3"
or
"4"
position
Inhibitor switch D,
1, 2
and
R
range P and
N
range
—

Water thermo switch (Elec-trical fan) Terminal disconnected Terminal connected While fan
not
operating

4B-25

4B SWITCH MONITOR FUNCTION
49 H018 9A1
INSPECTION PROCEDURE
1. Warm up the engine to normal operating temper-
ature and stop it.
2. Connect the SST to the check connector (Green,
6-pin) and the negative battery terminal.
86U04A-034
76G04B-023
3. Connect a jumper wire between the test connec-
tor (Green, 1-pin) and a ground.
4. Turn the ignition switch ON. Check if monitor lamp
illuminates when each switch is made to function
as described below.
Caution
a) If any one of the switches is activated, the
monitor lamp will stay on.
b) Do not start the engine.
Note
The Digital Code Checker (49 G018 9A0) with
the Signal Adapter (49 9200180) may be used
in place of the Self-Diagnosis Checker.
Procedure
76G04B-024
4B—26

IDLE ADJUSTMENT 4B
76G04B-034
76G04B-035
Idle mixture
Automatic
Control
Function
Engine Control Unit

IDLE
ADJUSTMENT
IDLE SPEED
Preparation
1) Check the condition of the engine (plugs, leaks in
hoses, etc.).
2) Make sure all accessories are OFF.
3) Warm up the engine and run it for three minutes
at 2,500—3,000 rpm in neutral.
4) Check the initial ignition timing and adjust if
necessary.
Inspection and Adjustment
Caution
Disconnect the air bypass solenoid connec-
tor when checking and adjusting the idle
speed.
1. Check that the idle speed is within specification.
Specification:
MTX—800 +58 rpm
ATX—900 +58 rpm (P range)
2. If the idle speed is not within specification, remove
the blind cap from the throttle body and adjust it
by turning the air adjust screw.
IDLE MIXTURE
Because an automatic compensation function
for air/fuel mixture is built into the engine con-
trol unit, it is not necessary to check and adjust
the idle mixture.
86U04A-049
4B-29

FUEL SYSTEM 4B
COMPONENT DESCRIPTIONS
Component Function Remarks
Air flow meter
Detects amount
of
intake
air;

sends signal
to
engine control unit Intake
air
thermo sensor and fuel pump
switch
are
integrated

Atmospheric pressure sensor
Detects atmospheric pressure; sends sig-nal
to
engine control unit

Circuit opening relay
Voltage
for
fuel pump while engine running

Clutch switch
Detects in-gear condition; sends signal
to
engine control unit Switch
ON
when clutch pedal released

Engine control unit
Detects signals from input sensors and switches; controls injector operation

Fuel filter
Filters particles from fuel

Fuel pump
Provides fuel
to
injectors • Operates while engine running
• Installed
in
fuel tank

Idle switch
Detects when throttle valve fully closed;
sends signal
to
engine control unit
Installed
in
throttle sensor

Ignition coil (-) terminal
Detects engine speed; sends signal
to
engine control unit

Ignition switch (ST position)
Sends engine cranking signal
to
engine control unit

Inhibitor switch
Detects in-gear condition; sends signal
to
engine control unit
Switch
ON in "N" or "P"
range

Injector
Injects fuel into intake port • Controlled
by
signals from engine control unit • High-ohmic injector

Intake air thermo sensor
Detects intake
air
temperature;
sends signal
to
engine control unit Installed
in air
flow meter

Main relay
Supplies electric current
to
injectors and engine control unit

Neutral switch
Detects in-gear condition; sends signal
to
engine control unit
Switch
ON
in-gear

Oxygen sensor
Detects Oxygen concentration; sends sig-nal
to
engine control unit
Zirconia ceramic and platinum coating

Pressure regulator
Adjusts fuel pressure supplied
to
injectors

Pulsation damper
Absorbs fuel pulsation

Throttle sensor
Detects throttle valve opening angle; sends signal
to
engine control unit
Integrated idle switch

Water thermo sensor
Detects coolant temperature;
sends signal
to
engine control unit

Water thermo switch
Detects radiator coolant temperature; sends signal
to
engine control unit ON: above 17°C (63°F)

76G04B-058
4B—43

FUEL SYSTEM 4B
86U04A-068
FUEL PRESSURE RELEASE AND SERVICING
FUEL SYSTEM
Fuel in the fuel system remains under high pressure
even when the engine is not running.
a) Before disconnecting any fuel line, release the fuel
pressure from the fuel system to reduce the pos-
sibility of injury or fire.
1. Start the engine.
2. Disconnect the circuit opening relay.
3. After the engine stalls, turn OFF the ignition
switch.
4. Reconnect the circuit opening relay.
b) Use a rag as protection from fuel spray when dis-
connecting the hoses.
Plug the hoses after removal.
c) When inspecting the fuel system, use the SST.
86U04A-069
4B—45

FUEL SYSTEM 4B
Pressure .
regulator ^^ \ To multi-pressure tester
How to Connect Multi-Pressure Tester
Warning
Before connecting the SST, release the fuel
pressure from the fuel system to reduce the
possibility of injury or fire. (Refer to page
4B—45.)
1. Disconnect the negative battery terminal.
2. Disconnect the fuel main hose from the fuel filter.
3. Connect the SST between the fuel main hose and
fuel pump with the adapter.
Caution
Do not reverse the adapter connection.
4. Disconnect the vacuum hose from the pressure
regulator control solenoid valve. Connect the SST
vacuum hose with a three-way joint.
5. Connect the negative battery terminal.
6. Connect the SST to the battery.
86U04A-071
v *
- i\zLTest connector (Yellow)
7. Connect the terminals of the test connector (Yel-
low) with a jumper wire. Turn the ignition switch
ON to operate the fuel pump.
8. Check for fuel leaks.
Caution
After checking for fuel leakage, turn the igni-
tion switch OFF and disconnect the jumper
wire from the test connector.
86U04A-072
4B—47