1987 MAZDA 626 ignition

4A CONTROL SYSTEM
Terminal
(Wire color) Connected to Condition Voltage

2K
— — —

2L
(BR) Inhibitor switch "P"
or "N"
range Below 1,5V 2L
(BR) Inhibitor switch
Others Battery voltage
2M
(BY)
Ignition switch
(START position)
Ignition switch
ON
Below 1,5V 2M
(BY)
Ignition switch
(START position) Cranking Battery voltage
2N
— — —
76G04A-172
(2M X
2
X
2F 2C

X 2L
2J 2H 2F 2D 2B

fll X >< X

1J 1H
>< X
1B

FE and F8 Engine — MTX (General)
Terminal (Wire color) Connected to Condition Voltage

A
(W)
Headlight switch Headlight switch
ON
Below 1,5V A
(W)
Headlight switch
Headlight switch OFF Battery voltage
B
(B)
Ground
—
Below 1,5V
C
(BL) Rear defroster switch Rear defroster switch
ON
Below 1,5V C
(BL) Rear defroster switch
Rear defroster switch OFF Battery voltage
D
(LG) A/C switch A/C operated Below 1.5V D
(LG) A/C switch
A/C not operated Battery voltage
E
(LB) Solenoid valve (Main
air

bleed control)
Intake manifold vacuum more than 300 mmHg (11.8 inHg), and radiator coolant temperature above 17°C (63 °F)
Battery voltage E
(LB) Solenoid valve (Main
air

bleed control)
Others Below 1.5V
F
(GW)
Water thermo switch
(Radiator)
Radiator coolant temperature below 17°C (63°F) Below 1,5V F
(GW)
Water thermo switch
(Radiator) Radiator coolant temperature above 17°C (63°F) Battery voltage
G (YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature below 72°C (162°F) Below 1,5V H
(L)
Water thermo switch (Intake manifold) Engine coolant temperature above 72°C (162°F) Battery voltage
I
— — —

J
(BW)
Ignition switch Ignition switch
ON
Battery voltage
K
— —

L
— — —

M
— — —

N
— —
4A-90

CONTROL SYSTEM 4 A
Terminal (Wire color) Connected to Condition Voltage

0 (BY)
Ignition switch*
(START position) Ignition switch
ON
Below 1.5V 0 (BY)
Ignition switch*
(START position) Cranking Battery voltage
P
(LW) Solenoid valve (A/C) A/C switch
ON
and engine speed below approx.
2,300
rpm
Below 1,5V
Others Battery voltage
Q (YW) Idle-up solenoid valve Headlight switch ON, rear defroster switch ON,
fan
speed control switch
is
3rd
or
4th position, A/C oper-ated,
or
engine coolant temperature below 72°C (162°F)
Below 1,5V
Others Battery voltage
R
(LB)
Fan speed control switch Fan speed control switch
in
3rd
or
4th position Below 1,5V R
(LB) Fan speed control switch OFF Battery voltage
*
Not
used
76G04A-173

{
Q
0
><
K
X
G E C A
^

R P
R X
J H F D B

FE 8Valve — Unleaded Fuel
Terminal (Wire color) Connected to Condition Voltage

A
(L)
Coast enrichment solenoid valve Engine speed approx. 1,500—2,300 rpm and idle switch
ON

Below 1,5V A
(L)
Coast enrichment solenoid valve
Others Battery voltage
B
(B)
Ground
—
Below 1,5V
C (LB)
Air bypass solenoid valve Engine speed above approx. 3,500 rpm and idle
switch
ON

Below 1,5V C (LB)
Air bypass solenoid valve
Others Battery voltage
D
(YL)
Ignition coil Ignition switch
ON or
engine running Battery voltage
E
— — —

F
(BW)
Ignition switch Ignition switch
ON
Battery voltage
G (YW) Slow fuel cut solenoid valve Engine speed above approx. 2,300 rpm and idle
switch
ON

Battery voltage G (YW) Slow fuel cut solenoid valve
Others Below 1.5V
H
(LW) A/C switch A/C operated and engine speed above approx.
1,500 rpm
Battery voltage H
(LW) A/C switch
A/C not operated
or
engine speed below approx.
1,500 rpm
Below 1,5V

4A—91

4A CONTROL SYSTEM
Terminal
(Wire color) Connected to Condition Voltage

I
(LgB)
Idle switch Idle switch
ON
Below 1.5 V I
(LgB)
Idle switch
Idle switch OFF Battery voltage
J
— —
76G04A-174
( I
G
X
C
0
X
H F D B

F6 Engine (Singapore)
Terminal
(Wire color) Connected to Condition Voltage

A
— — —

B
(YL) Ignition coil Ignition switch
ON
and engine running Battery voltage
C
(B)
Ground
— —

D
(GB) Relay Engine speed below approx. 2,100
rpm
Below 1,5V D
(GB) Relay
Engine speed above approx. 2,100
rpm
Battery voltage
F
(BW) Ignition switch Ignition switch
ON
Battery voltage

76G04A-175
4A—92

CONTROL SYSTEM 4 A
76G04A-176
76G04A-177
76G04A-178
Replacement
1. Disconnect the negative battery cable.
2. Remove the front console covers (right or left).
3. Disconnect the connectors from the control unit.
4. Remove and replace the control unit.
INHIBITOR SWITCH
Inspection
1. Verify that the starter operates with the ignition
switch at START position in
P
and N positions only.
2. Check that the back-up lights illuminate when R
position selected and the ignition switch is ON.
3. If not as specified, check the following:
(1) Jack up the vehicle and support it with safety
stands.
(2) Disconnect the inhibitor switch connector.
(3) Check continuity of the switch with an
ohmmeter.
Connecting guide

Position

N

D,1,2
Connector terminal

O -O
O
O
-O
-O

O—O: indicates continuity

4. Replace if necessary.
IDLE SWITCH
Inspection
1. Warm up the engine and run it at idle.
2. Turn all accessories OFF.
3. Connect a tachometer to the engine.
4. Connect a voltmeter to the carburetor connector
F terminal.
76G04A-179
4A-93

TROUBLESHOOTING GUIDE 4B
TROUBLESHOOTING GUIDE
This troubleshooting guide shows the malfunction numbers and the symptoms of various failures.
Perform troubleshooting as described below.
Possible cause
Symptom
Input sensors and switches
o> Q.
C
0
Jh c 01
4B-14
a> 4)
E
o
4B-1S
o in c « m o E k_ 0) c.
0 <0 £
4B-16
o CO c a> 0) o E
a>
.x
co
4B-17
o 10 c a) co
4B-18
o in c a> (0
o> o> a>
a) £ a VI o E
4B-19
0 <0 c a> 0) c a> 01
S? o
4B-20
E a> in (0
o 10 A •o 0) 0> u.
4B-21
Output solenoid valves
o «
3 O) 0)
0) 0) 01
0> > 10 >
•o o c V o tt)
4B-22
0)
OI

0> > CO >

TJ
O c 0> o CO
4B-23
oc O u
o> > 75 >
•o o c a> o 05
4B-23
0 a. 3 1
2
0) > (0 >
"D O
o 0> in in a a >. £
4B-23
ffl a 3 • a>
2
a> > 10 >
"O o c a> o
CO Q. >. JO
4B-24
Fault Indicated by SST
Code No. 01 08 09 10 12 14 15 17 25 26 28 34 35
Hard start or won't start
(Cranks OK)
Engine stalls
Rough
idle
While warming up
After warming up
While warming up
After warming up
High idle speed after
warming up
TROUBLESHOOTING PROCEDURE
Note
Step 1 under symptom is to quickly determine what system or unit may be at fault by use of the SST. (Self-Diagnosis Checker 49 H018 9A1)
1st:
Check input sensors and output solenoid valves with the
SST.
(Refer
to
page 4B—10.)

2nd:
Check other switches with the
SST.
(Refer
to
page 4B—26.)

3rd:
Check the following items:

11
Poor acceleration, hesita-
tion or lack of power
Runs rough on deceleration
Afterburn in exhaust system
Poor fuel consumption
Engine stalls or rough after hot starting
Electrical system
1) Battery condition
2) Fuses

Fuel system
1) Fuel level 2) Fuel leakage
3) Fuel filter 4) Idle speed

Engine
1) Compression 2) Overheating

Ignition system

1) Ignition spark 2) Ignition timing

Intake air system
1)
Air
cleaner element 2) Vacuum
or air
leakage 3) Vacuum hose routing
4) Accelerator cable

Others
1) Clutch slippage 2) Brake dragging

Fails emission test 4th:
Check Fuel and Emission Control Systems. (Refer
to
page 4B—8.)

76G04B-003
4B—7

TROUBLESHOOTING WITH SST 4B
TROUBLESHOOTING WITH SST
When troubles occur in the main input devices or output devices, check for the cause using the SST.
Failures of each input and output device are indicated and retrieved from the control unit as malfunc-
tion code numbers.
Note
The control unit constantly checks for malfunction of the input devices. But, the control
unit checks for malfunction of output devices only in a 3 second period after the ignition
switch is turned ON and the test connector is grounded.
4B—9

4B TROUBLESHOOTING WITH SST
INSPECTION PROCEDURE
1. Connect the SST to the check connector, (Green,
6-pin) and the negative battery terminal.
2. Set the select switch to position A.
Note
The check connector is located at the rear of
the left side wheel housing.
86U04A-011
Test connector: Green (1 pin)
3. Ground the test connector (Green, 1-pin) with a
jumper wire.
Note
The test connector is located near the Self-
Diagnosis Checker check connector.
86U04A-012
OO
uu
SELF-DIAGNOSIS CHECKER
(WPUTOft
SELECT
S*

5


o n==ru
o o o o 49 HO 18 9AI
76G04B-005
4. Turn the ignition switch ON.
5. Verify that 88 flashes on the digital display and that
the buzzer sounds for three seconds after turn-
ing the ignition switch ON.
6. If 88 does not flash, check the main relay (Refer
to page 4B—86), power supply circuit, and check
connector wiring.
7. If 88 flashes and the buzzer sounds continuously
for more than 20 seconds, replace the engine con-
trol unit and perform steps 3 and 4 again.
8. Note the code numbers and check for the causes
by referring to the check sequences shown on
pages from 4B—14 to 4B—24. Repair as
necessary.
Note
Cancel the code numbers by performing the
after-repair procedure after repairing.
AFTER-REPAIR PROCEDURE
1. Cancel the memory of malfunctions by disconnect-
ing the negative battery cable and depressing the
brake pedal for at least 2 seconds; then recon-
nect the negative battery cable.
76G04B-134
4B—10

TROUBLESHOOTING WITH SST 4B
2. Connect the SST to the check connector.
3. Ground the test connector (Green, 1-pin) with a
jumper wire.
86U04A-015

Ignition switch:
ON

for six
seconds
4. Turn the ignition switch ON, but do not start the
engine for six seconds.
5. Start and warm up the engine, then run it at
2,500—3,000 rpm for three minutes in neutral.
6. Verify that no code numbers are displayed.
76G04B-006
76G04B-007
Note
The Digital Code Checker (49 G018 9A0) with
the Signal Adapter (49 9200 180) may be used
in place of the Self-Diagnosis Checker (49
H018 9A1).
4B-11