1987 MAZDA 626 water pump

EGR SYSTEM 4A
TROUBLESHOOTING
Note
Make the system inspection first. If no problem is found, continue with the next inspec-
tion of the Troubleshooting Guide. (Refer to pages 4A—22.)
Possible cause System inspection EGR control valve Water thermo valve
Page 4A—65 4A—65 4A—66
Checking order 1 2 3
76G04A-123
76G04A-124
76G04A-125
System Inspection
1. Start the engine.
2. Accelerate the engine while it is still cold and check
that the diaphragm of the EGR control valve does
not move.
3. Warm up the engine to normal operating temper-
ature and run it at idle.
Warning
Be careful when checking the EGR control
valve, the surrounding area is very hot.
4. Accelerate the engine and check that the di-
aphragm of the EGR control valve moves.
EGR Control Valve (ATX)
(No. 1)
1. Manually actuate the valves by pushing on the di-
aphragm with finger.
2. Check that the spring resistance is present and the
diaphragm moves freely with no sticking or
binding.
3. Warm up the engine and run it at idle.
4. Connect a vacuum pump to the valve and apply
vacuum.
5. Check that the engine runs roughly or stalls at more
than the specified vacuum.
Specification:
70—90 mmHg (2.8—3.5 inHg)
6. If not correct, replace the EGR control valve.
76G04A-126
4A—65

4A EGR SYSTEM
76G04A-127
76G04A-128
ji C
Blow here *** I
>3 l^v?
> O-—-/ 1)
Ml
r-
(No. 2)
1. Check the EGR control valve manually (same as
No. 1 valve).
2. Warm up the engine and run it at idle.
3. Connect a vacuum pump to the valve and apply
vacuum.
4. Check that the engine runs roughly or stalls at more
than the specified vacuum.
Specification:
70—90 mmHg (2.8—3.5 inHg)
5. If not correct, replace the EGR control valve.
EGR Control Valve (MTX)
1. Check the EGR control valve manually (same as
above).
2. Warm up the engine and run it at idle.
3. Connect a vacuum pump to the valve and apply
vacuum.
4. Check that the engine runs roughly or stalls at more
than the specified vacuum.
Specification:
70—90 mmHg (2.8—3.5 inHg)
5. If not correct, replace the EGR control valve.
Water Thermo Valve
1. Remove the water thermo valve from the bottom
of the inlet manifold.
2. Place the water thermo valve in a container with
water and a thermometer.
3. Gradually heat the water to 50°C (122°F).
76G04A-129
From carburetor
(A)—E
(a)-
To No.1 EGR
control valve and
vacuum switch
Wax
I— (B)
(b)
To No.2 EGR
control valve
76G04A-130
4. Blow air through the water thermo valve from (A),
and check that air comes out from (a).
5. Blow air through the water thermo valve from (B)
and check that air comes out from (b).
6. Replace if necessary.
4A—66

EVAPORATIVE EMISSION CONTROL SYSTEM 4A
Troubleshooting
Possible cause No. 1 purge No. 2 purge Water thermo Three-way control valve control valve valve check valve
Page 4A—79 4A—79 4A—79 4A—37
Checking order 1 2 3 4
76G04A-156
No. 1 Purge Control Valve
1. Blow through the purge control valve from port A
and check that air does not flow.
2. Connect a vacuum pump to the purge control
valve.
3. Apply 110 mmHg (4.29 inHg) vacuum with a
vacuum pump, and blow through port A again; air
should flow.
76G04A-157
No. 2 Purge Control Valve
1. Disconnect vacuum hose A from the pipe.
2. Check the air flow of the No. 2 purge control valve.
Specification:
15—35 mmHg (0.6—1.4 inHg): Below
-8—18 mmHg (0.3—0.7 inHg): Suck
76G04A-158
(B)"
* = zu
Blow
'(A)
/ (ft
Water Thermo Valve
1. Remove the water thermo valve.
2. Place the valve in water with a thermometer.
3. Heat the water gradually to 50°C (122°F).
4. Blow through the valve from hose A and check that
air comes out of port B.
76G04A-159
4A-79

FUEL AND EMISSION
CONTROL SYSTEMS
(FUEL INJECTION FE)
OUTLINE 4B— 2
SYSTEM DIAGRAM 4B— 2
COMPONENT LOCATION 4B— 3
VACUUM HOSE ROUTING
DIAGRAM 4B— 5
SPECIFICATIONS 4B— 6
TROUBLESHOOTING GUIDE 4B— 7
TROUBLESHOOTING
PROCEDURE 4B— 7
TROUBLESHOOTING WITH SST.... 4B— 9
INSPECTION PROCEDURE 4B—10
AFTER-REPAIR PROCEDURE 4B—10
PRINCIPLE OF CODE CYCLE 4B—12
CODE NUMBER 4B—13
SWITCH MONITOR FUNCTION 4B—25
INSPECTION PROCEDURE 4B—26
IDLE SPEED 4B—29
IDLE MIXTURE 4B—29
INTAKE AIR SYSTEM 4B—30
COMPONENT DESCRIPTIONS 4B—30
REMOVAL 4B—31
PARTS INSPECTION 4B—32
INSTALLATION 4B—34
IDLE-UP SYSTEM 4B—35
COMPONENT DESCRIPTIONS 4B—36
TROUBLESHOOTING 4B—37
AIR VALVE 4B—38
AIR BYPASS SOLENOID VALVE ... 4B—39
FUEL SYSTEM 4B—42
COMPONENT DESCRIPTIONS 4B—43
TROUBLESHOOTING 4B—44
FUEL PRESSURE RELEASE AND
SERVICING FUEL SYSTEM 4B—45
MULTI-PRESSURE TESTER 4B—46
FUEL PRESSURE 4B—48
FUEL PUMP 4B—49
PULSATION DAMPER 4B—50
INJECTOR 4B—51
PRESSURE REGULATOR
CONTROL SYSTEM 4B—53
COMPONENT DESCRIPTIONS 4B—54
TROUBLESHOOTING 4B—55
REPLACEMENT 4B—57
FUEL TANK 4B—61
DECELERATION CONTROL
SYSTEM 4B—64
COMPONENT DESCRIPTIONS 4B—65
TROUBLESHOOTING 4B—66
AIR INJECTION SYSTEM 4B—68
COMPONENT DESCRIPTIONS 4B—68
TROUBLESHOOTING 4B—69
EXHAUST GAS RECIRCULATION
(EGR) SYSTEM 4B—71
COMPONENT DESCRIPTIONS 4B—71
TROUBLESHOOTING 4B—72
EVAPORATIVE EMISSION
CONTROL (EEC) SYSTEM 4B—74
COMPONENT DESCRIPTIONS 4B—74
TROUBLESHOOTING 4B—75
POSITIVE CRANKCASE
VENTILATION (PCV) SYSTEM 4B—80
COMPONENT DESCRIPTION 4B—80
EXHAUST SYSTEM 4B—81
REMOVAL AND INSTALLATION ... 4B—82
INSPECTION 4B—82
CONTROL SYSTEM 4B—83
RELATIONSHIP CHART 4B—84
EGI MAIN FUSE 4B—86
MAIN RELAY 4B—86
CIRCUIT OPENING RELAY 4B—86
ENGINE CONTROL UNIT 4B—87
NEUTRAL SWITCH 4B—91
CLUTCH SWITCH 4B—91
BRAKE LIGHT SWITCH 4B—91
P/S PRESSURE SWITCH 4B—92
INHIBITOR SWITCH 4B—92
E/L CONTROL UNIT 4B—93
AIR FLOW METER 4B—94
THROTTLE SENSOR 4B—95
WATER THERMO SENSOR 4B—97
WATER THERMO SWITCH 4B—97
OXYGEN SENSOR 4B—98
ATMOSPHERIC PRESSUFfE
SENSOR 4B—99
76G04B-001

FUEL SYSTEM 4B
COMPONENT DESCRIPTIONS
Component Function Remarks
Air flow meter
Detects amount
of
intake
air;

sends signal
to
engine control unit Intake
air
thermo sensor and fuel pump
switch
are
integrated

Atmospheric pressure sensor
Detects atmospheric pressure; sends sig-nal
to
engine control unit

Circuit opening relay
Voltage
for
fuel pump while engine running

Clutch switch
Detects in-gear condition; sends signal
to
engine control unit Switch
ON
when clutch pedal released

Engine control unit
Detects signals from input sensors and switches; controls injector operation

Fuel filter
Filters particles from fuel

Fuel pump
Provides fuel
to
injectors • Operates while engine running
• Installed
in
fuel tank

Idle switch
Detects when throttle valve fully closed;
sends signal
to
engine control unit
Installed
in
throttle sensor

Ignition coil (-) terminal
Detects engine speed; sends signal
to
engine control unit

Ignition switch (ST position)
Sends engine cranking signal
to
engine control unit

Inhibitor switch
Detects in-gear condition; sends signal
to
engine control unit
Switch
ON in "N" or "P"
range

Injector
Injects fuel into intake port • Controlled
by
signals from engine control unit • High-ohmic injector

Intake air thermo sensor
Detects intake
air
temperature;
sends signal
to
engine control unit Installed
in air
flow meter

Main relay
Supplies electric current
to
injectors and engine control unit

Neutral switch
Detects in-gear condition; sends signal
to
engine control unit
Switch
ON
in-gear

Oxygen sensor
Detects Oxygen concentration; sends sig-nal
to
engine control unit
Zirconia ceramic and platinum coating

Pressure regulator
Adjusts fuel pressure supplied
to
injectors

Pulsation damper
Absorbs fuel pulsation

Throttle sensor
Detects throttle valve opening angle; sends signal
to
engine control unit
Integrated idle switch

Water thermo sensor
Detects coolant temperature;
sends signal
to
engine control unit

Water thermo switch
Detects radiator coolant temperature; sends signal
to
engine control unit ON: above 17°C (63°F)

76G04B-058
4B—43

4B EEC SYSTEM
EVAPORATIVE EMISSION CONTROL
(EEC)
SYSTEM
Engine control unit
Solenoid valve
(Purge control)
Vacuum
switch
valve x
From water thermo valve To dynamic -chamber
Three-way
check valve
Orifice Charcoal
canister
From fuel tank
No.2 purge
control valve
Fuel tank
86U04A-136
This system stores fuel vapor generated in the fuel tank in the canister when the engine is not running.
The fuel vapor is stored in the canister until it is drawn into the dynamic chamber and burned when
the engine is started.
COMPONENT DESCRIPTIONS
Component Function Remarks
Air flow meter Detects amount of intake air; sends signal to engine control unit
Intake air thermo sensor and fuel pump
switch are integrated
Charcoal canister Stores fuel tank fumes when engine
stopped
Engine control unit Detects signals from input sensors and switches; controls solenoid valve (Purge control)
Ignition coil (-)
terminal Detects engine speed; sends signal to
engine control unit
Separator Prevents fuel from flowing into charcoal canister
Solenoid valve (Purge control) Controls vacuum line to vacuum switch valve
Three-way check valve Controls pressure in fuel tank
Vacuum switch valve Regulates evaporative fumes from canis-
ter to intake manifold
Water thermo sensor Detects coolant temperature; sends signal to engine control unit
Water thermo valve Controls vacuum applied to No.1 purge control valve and solenoid valve (Purge control)
Opens vacuum line above 54°C (129°F)
76G04B-104
4B—74

4B EEC SYSTEM
Water Thermo Valve
1. Remove the water thermo valve.
2. Immerse the valve in a water-filled container.
3. Heat the water gradually and observe the tem-
perature.
4. Blow through the valve from one vacuum port and
verify that air comes out of the other port at
46—54°C (115—129°F).
86U04A-147
Three-way
check valve
86U04A-148
To canister
Pressure valve
3<> A To tank
Vacuum valve
Air filter
Three-Way Check Valve
1. Remove the check valve.
2. Blow through the valve from port A, and check that
air comes out of port B.
Next, block port B and check that air comes out
of port C.
3. Block port B.
4. Connect a vacuum pump to port A and verify that
no vacuum is held.
86U04A-149
Solenoid valve (Purge control)
Solenoid Valve (Purge control)
1. Remove the solenoid valve.
76G04B-128
4B-78

4C
FUEL AND EMISSION
CONTROL SYSTEMS
(FUEL INJECTION FE DOHC)
OUTLINE 4C— 2
COMPONENT APPLICATION 4C— 2
SYSTEM DIAGRAM 4C— 3
COMPONENT LOCATION 4C— 4
VACUUM HOSE ROUTING
DIAGRAM 4C— 7
SPECIFICATIONS 4C— 8
TROUBLESHOOTING GUIDE 4C— 9
TROUBLESHOOTING WITH SST.. 4C— 11
INSPECTION PROCEDURE 4C— 12
PRINCIPLE OF CODE CYCLE 4C— 13
CODE NUMBER 4C— 14
SWITCH MONITOR FUNCTION 4C— 25
INSPECTION PROCEDURE 4C— 26
IDLE ADJUSTMENT 4C— 29
IDLE SPEED 4C— 29
IDLE MIXTURE 4C— 30
INTAKE AIR SYSTEM 4C— 31
COMPONENT DESCRIPTION 4C— 31
REMOVAL 4C— 32
PARTS INSPECTION 4C— 33
REPLACEMENT 4C— 36
INSTALLATION 4C— 37
VARIABLE INERTIA CONTROL
(VIC) SYSTEM 4C— 39
COMPONENT DESCRIPTION 4C— 40
TROUBLESHOOTING 4C— 40
IDLE SPEED CONTROL
(ISC) SYSTEM 4C— 44
COMPONENT DESCRIPTION 4C— 45
TROUBLESHOOTING 4C— 46
REMOVAL 4C— 48
FUEL SYSTEM 4C— 49
COMPONENT DESCRIPTION 4C— 50
TROUBLESHOOTING 4C— 51
FUEL PRESSURE RELEASE AND
SERVICING FUEL SYSTEM 4C— 52
MULTI-PRESSURE TESTER 4C— 53
FUEL PUMP 4C— 56
PULSATION DAMPER 4C— 57
INJECTOR 4C— 57
TRANSFER PUMP CONTROL
SYSTEM 4C— 59
REPLACEMENT 4C— 60
FUEL TANK 4C— 65
PRESSURE REGULATOR
CONTROL (PRC) SYSTEM 4C— 68
COMPONENT DESCRIPTION 4C— 69
TROUBLESHOOTING 4C— 69
DECELERATION CONTROL
SYSTEM 4C— 72
COMPONENT DESCRIPTION 4C— 73
TROUBLESHOOTING 4C— 73
ELECTRONIC SPARK ADVANCE
(ESA) CONTROL SYSTEM 4C— 75
COMPONENT DESCRIPTION 4C— 76
TROUBLESHOOTING 4C— 76
EXHAUST GAS RECIRCULATION
(EGR) SYSTEM 4C- 77
COMPONENT DESCRIPTION 4C— 77
TROUBLESHOOTING 4C— 78
EVAPORATIVE EMISSION
CONTROL (EEC) SYSTEM 4C— 80
COMPONENT DESCRIPTION 4C— 80
TROUBLESHOOTING 4C— 81
POSITIVE CRANKCASE
VENTILATION (PCV) SYSTEM.... 4C— 86
COMPONENT DESCRIPTION 4C— 86
PCV VALVE 4C— 86
EXHAUST SYSTEM
(UNLEADED FUEL) 4C— 87
REMOVAL AND INSTALLATION.. 4C— 88
INSPECTION 4C— 88
EXHAUST SYSTEM
(LEADED FUEL) 4C— 89
REMOVAL AND INSTALLATION.. 4C— 90
CONTROL SYSTEM 4C— 91
RELATIONSHIP CHART 4C— 92
EGI MAIN FUSE 4C— 96
CONTROL RELAY 4C— 96
NEUTRAL SWITCH 4C— 97
CLUTCH SWITCH 4C— 97
P/S PRESSURE SWITCH 4C— 97
ENGINE CONTROL UNIT 4C— 98
E/L CONTROL UNIT 4C—102
AIR FLOW SENSOR 4C—103
THROTTLE SENSOR 4C—104
IDLE SWITCH 4C—106
WATER THERMO SWITCH 4C—106
WATER THERMO SENSOR 4C—107
OXYGEN SENSOR 4C—107
DISTRIBUTOR 4C—108
OXYGEN SENSOR HEATER 4C—109
KNOCK SENSOR 4C—109
INTAKE AIR THERMO SENSOR .. 4C—110
76G04C-001