1987 MAZDA 626 Exhaust

CHASSIS NUMBER LOCATION/ABBREVIATIONS/UNITS G
CHASSIS NUMBER LOCATION UNITS
67U0GX-005
ENGINE MODEL AND
NUMBER LOCATION
Nm (m-kg, ft-lb or in-lb). Torque
rpm Revolutions per minute A Ampere(s) V Volt(s) U Ohm(s) (resistance) kPa (psi) Pressure
(usually positive) mrriHg (in Hg) Pressure
(usually negative) W Watt
76G0GX-004
ABBREVIATIONS
67U0GX-007
AAS Auto adjusting suspension A/C Air conditioner ACC Accessories ABDC After bottom dead center ATDC After top dead center ATX Automatic transaxle ATF Automatic transmission fluid ABS Anti-lock brake system BBDC Before bottom dead center BTDC Before top dead center EX Exhaust EC-AT Electronically controlled automatic transaxle ESPS Engine speed sensing power steering EC PS Electronically-controlled power steering HLA Hydraulic lash adjuster IG Ignition IN Intake IC Integrated circuit INT Intermittent LH Left hand
MTX Manual transaxle M Motor OFF Switch off ON Switch on PCV Positive crankcase ventilation P/S Power steering P/W Power window RH Right hand RF-CX Comprex supercharged RF
engine
RF-N Normally aspirated RF engine ST Start sw Switch SST Special tools 4WS 4-wheel steering
PWS 2-wheel steering
4HAT 4-speed hydraulic automatic
transaxle Fl Fuel injection
76GQGX-005
G—9

0 PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
EXTERIOR
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Glass, exterior bright metal and paint for damage
• Wheel lug nuts
88—118 N m (9—12 m-kg, 65—87 ft-lb)
• Tire pressures (Refer to section 12)
• All weatherstrips for damage or detachment
• Operation of bonnet release and lock
• Operation of fuel lid and trunk lid (Back door) opener
• Door operation and alignment
• Headlight aiming
INSTALL following parts:
• Wheel caps or rings (if equipped)
• Outside rear view mirror(s)
UNDER BONNET—ENGINE OFF
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Fuel, coolant and hydraulic lines, fittings, connections and
components for leaks
• Engine oil level
• Power steering fluid level (if equipped)
• Brake and clutch master cylinder fluid level (if equipped)
• Windshield washer reservoir fluid level
• Radiator coolant level and specific gravity
Protection °C (°F) Specific gravity at 20°C (68°F)
-4 (25) 1.028
-16(3) 1.054
-26 (-15) 1.066 -40 (-40) 1.078
• Tightness of water hose clamps (including heater hoses)
• Tightness of battery terminals
• Manual transaxle oil level
• Drive belt tensions (Refer to section 1)
• Accelerator cable and its linkage for free movement
• Headlight cleaner fluid level (if equipped)
CLEAN spark plugs
INTERIOR
INSTALL the following parts:
• Rubber stopper for inside rear view mirror
• Fuse for accessories
CHECK the operations of the following items:
• Seat controls (sliding and reclining) and head rest
• Door locks including childproof door locks (if equipped)
• Seat belts and warning system
• Ignition switch and steering lock
• Inhibitor switch (ATX only)
• All lights including warning and indicator lights
• Sound warning system
• Headlight cleaner (if equipped)
• Horn, wipers and washers (front and rear, if equipped)
• Radio and antenna (if equipped)
• Cigarette lighter and clock
• Remote control outside rear view mirrors (if equipped)
• Power windows (if equipped)
• Heater, defroster and air conditioner at various mode
selection (if equipped)
• Sunroof (if equipped)
ADJUST antenna trimmer on radio (if equipped)
CHECK the following items:
• Presence of spare fuse
• Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
• Operation and fit of windows
• Pedal height and free play of brake and clutch pedal
Pedal height mm (in) free play mm (in)
Clutch pedal 216.5-221.5 (8.52-8.72) 5-13 (0.2-0.51)
Brake pedal 222-227 (8.74-8.94) 4-7 (0.16-0.28)
• Parking brake
5-7 noches/98 N (10 kg, 22lb)
UNDER BONNET—ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
• Operation of idle-up system for air conditioner or power
steering (if equipped)
• Automatic transaxle fluid level
• Operation of dash pot
• Initial ignition timing
• Idle speed
ON HOIST
CHECK the following items:
• Underside fuel, coolant and hydraulic lines, fittings, con-
nections and components for leaks
• Tires for cuts or bruises
• Steering linkage, suspension, exhaust system and all un-
derside hardware for looseness or damage
REMOVE protective cover from brake discs
ROAD TEST"
CHECK the following items:
• Brake operation
• Clutch operation
• Steering control
• Operation of meters and gauge
• Squeaks, rattles or unusual noise
• Engine general performance (including turbo)
• Emergency locking retractors
• Cruise control system (if equipped)
AFTER ROAD TEST
REMOVE seat and floor mat protective covers
CHECK for necessary owner information materials, tools and
spare tire in vehicle
-76G00X-002
0-2

U1
Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item

x 1000 Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Miles x
1000 0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Battery electrolyte level and specific gravity A A A A O o O O • Electroyte level • Specific gravity 5-8
Drive belts A A A A A O 0 o O • Cracks or damage • Tension

1
A—7
1B—6
1C-7
Engine timing belts Replace every 100,000 Km o o o o — 1A—14 1B—11 1C—11
Engine valve clearance A A A A A o X X o
• Valve clearance: F8 (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE-12-valve, FE (DOHC) IN: 0; Maintenance free EX: 0; Maintenance free RF-CX, RF-N (Cold engine) IN: 0.25 mm (0.010 in) EX: 0.35 mm (0.014 in)
1A-10
1C—85
Intake and exhaust manifold nuts and
bolts T T T o o X X
• Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb)

1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X IN EX
1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X F8, FE 19-30 (1.9-3.1,
14-22)
22-28 (22—2.9, 16-21)

1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X
RF-CX RF-N 16-23 (1.6-2,3,
12-17)
22-26 (2.2-2.7,
16-20)

1
A—86 1B—68 1C—89
Engine oil *2 R R R R R R R R R o o 0 o
• Oil pan capacity F8, FE: 3.6 liters (3.8 US qt, 3.2 Imp qt) RF-CX, RF-N:
5.0 liters (5.3 US qt, 4.4 Imp qt)
2A—6
2B-6
Oil filter *2 R R R R R R R R o o o o
• Oil filter capacity F8, FE 12-valve
0.3 liters (0.32 US qt, 0.26 Imp qt) FE (DOHC)
0.2 liters (0.21 US qt, 0.18 Imp qt) RF-CX, RF-N
0.4 liters (0.42 US qt, 0.35 Imp qt)
2A—6
2B-6
Fuel filter (R) for carbretor model (R) R (R) R o 0 o o — 4A—37

Interval
Procedure & item
Number of Months or km, whichever corns first
Months

x
1000
Km
Miles x 1000
0.6
6
10
12
20
12
18
30
18
24
40
24
30
50
30
36
60
36
42
70
42
48
80
48
®3 ©4 Service data and inspection point Page
m z >
z o m
H >
00 I-m
m o m
c 3 a to Qt (0 O
A
Battery electrolyte level and specific gravity O o o o Electroyte level Specific gravity 5-8
Drive belts O O o o Cracks or damage Tension

1
A—7
1B-6
1C-7
Engine timing belts Replace Severy 100,000 Km O O o o
Engine valve clearance
Intake and exhaust manifold nuts and bolts
O
O
o o
Valve clearance: FE-8-valve (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE (DOHC)
IN: 0; Maintenance free EX: 0; Maintenance free RF-CX, RF-N (Cold engine) IN: 0.25 mm (0.010 in) EX: 0.35 mm (0.014 in)
O IN EX
FE FE DOHC 19-30(1.9-3.1,
14-22)
22-28 (2.2-2.9
16-21)
1A—14 1B—11 1C-11

1
A—10
1C-85
Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb)
1A—86
1B—68 CO 0 1 m o
m a
H m
o m
Engine oil O
Oil filter O
O o o
Oil pan capacity FE: 3.6 liters
(3.8 US qt, 3.17 Imp qt) RF-CX, RF-N: 5.0 liters (5.3 US qt, 4.4 Imp qt)
O o o
Oil filter capacity FE 8-valve
0.3 liters (0.32 US qt, 0.26 Imp qt) FE (DOHC)
0.2 liters (0.21 US qt, 0.18 Imp qt) RF-CX, RF-N
0.4 liters (0.42 US qt, 0.35 Imp qt)
2A-6
2B-6
2A-6
2B-6

o Interval Number of Months or km, whichever corns first
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page x 1000
Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Procedure & item Miles
x
1000 0.6 6 12 18 24 30 36 42 48
Exhaust system heat shields (unlead) I I O O O O • Clearance to body, and exhaust
system 4A-97
Body condition visual only Inspect annually o o O O • Inspect annually —
Tyres (including spare tyre) Infration
pressure adjustment I I I I o o o O • Check the air pressure 12-2
Hinges and cathes A A A A o o o O — —
Underside of vehicle I I I I o o o o — —
Seat belt I I I I o o o o • Opration and looseness 14—101
Road test I I I I o o o o — —
•>1 o o o x o -tx

Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item

x
1000
Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Miles x
1000 0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Choke system I I I I O O X X
• Carburetor linkage • Choke diaphragm • Choke valve clearance • Unloader system
4A—26
4A-34
4A-34
4A—33
Cooling system I I I I O O o o • Hoses for cracks or wear 3A-5 3B—4
Engine coolant (with reservoir) Reprace every 24 months O O o o • Coolant level 3 A—5 3B—4
Battery electrolyte level and specific gravity I I I I O o o o • Electrolyte level • Specific gravity 5—8
Engine timing belts *2 Replace every 100,000 km O o o o —
1A—14 1B—11 1C—11
Drive belts *4 A I I I I I I I I O o o o • Cracks or damage • Tension
1A—7
1
B—6 1C—7
Engine valve clearance
(1) For Gasoline engine (I) I (I) I (I) I (I) I
T
O o X o
• Valve clearance F6, F8, FE-8-valve (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE-12-valve, FE (DOHC) IN: 0; Maintenance free EX: 0; Maintenance free RF-N (Cold engine) IN: 0.25 mm (0.01 in) EX: 0.35 mm (0.014 in)
1A—10
1C—85
Exhaust manifold nuts and bolts T T
I
T o o X X
• Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb) 1A—86 1B—68 1C—89 Exhaust manifold nuts and bolts T T
I
T o o X X IN EX 1A—86 1B—68 1C—89 Exhaust manifold nuts and bolts T T
I
T o o X X
F6, F8, FE 19-30 (1.9-3.1, 14-22) 22-28 (2.2-2.9, 16-21)
1A—86 1B—68 1C—89 Exhaust manifold nuts and bolts T T
I
T o o X X
RF-N 16-23 (1.6-2.3,
12-17) 22-26 (2.2-2 7,
16-20)
1A—86 1B—68 1C—89
Engine oil *1 Replace every 5000 km or 6 months X X o o
• Oil pan capacity FE DOHC: 3.6 liters
(3.8 US qt, 3.2 Imp qt) RF-N: 5.0 liters
(5.3 US pt, 4.4 Imp qt)
2A-6
2B—6
m >
o m
H >
00 r~ m
a 2

TROUBLESHOOTING GUIDE 1 A
Problem Possible Cause Remedy Page
Insufficient power Insufficient compression Malfunction of HLA Improper valve clearance Compression leakage from valve seat Seized valve stem Weak or broken valve spring Failed cylinder head gasket Cracked or distorted cylinder head Sticking, damaged, or worn piston ring Cracked or worn piston
Replace
Adjust
Repair
Replace Replace Replace Replace Replace Replace
1A—75 1A—10
1
A—51 1A—49 1A—53
1
A—20 1A—48 1A—57
1
A—57
Malfunction of fuel system Refer to Section 4
Others Slipping clutch Dragging brakes Wrong size tires
Refer to Section 6 Refer to Section 11 Refer to Section 12
Abnormal
combustion
Malfunction of engine-related components Malfunction of HLA
Improper valve clearance Sticking or burned valve
Weak or broken valve spring Carbon accumulation in combustion chamber
Replace Adjust Replace Replace
Eliminate carbon

1
A—75 1A—10 1A—49 1A—53
Malfunction of fuel system Refer to Section 4
Engine noise Crankshaft or bearing related parts
Excessive main bearing oil clearance Main bearing seized or heat-damaged Excessive crankshaft end play Excessive connecting rod bearing oil clearance Connecting rod bearing seized or heat-damaged
Replace or repair Replace
Replace or repair Replace or repair Replace
1A—65
1
A—65 1A—66 1A—67
1
A—67
Piston related parts Worn cylinder Worn piston or piston pin Seized piston Damaged piston ring Bent connecting rod
Replace or repair
Replace
Replace Replace Replace
1A—55
1
A—57
1
A—57
1
A—57 1A—59
Valves or timing related parts Malfunction of HLA* Improper valve clearance Broken valve spring Excessive valve guide clearance Malfunction of timing belt tensioner
Replace Adjust
Replace Replace Replace
1A—75 1A—10 1A—53 1A—49 1A—61
Malfunction of cooling system Refer to Section 3A
Malfunction of fuel system Refer to Section 4
Others Malfunction of water pump bearing Improper drive belt tension Malfunction of alternator bearing Exhaust gas leakage
Replace Adjust Replace Repair
1 A— 7

1
A—48
* Tappet noise may occur if the engine is not operated for an extended period of time. The noise should stop after the
engine has reached normal operating temperature.
76G01A-005
1A—5

1A TUNE-UP PROCEDURE
76G01A-105
Idle Speed (Carburetor)
1. Connect a tachometer to the engine.
2. Turn all electric loads OFF.
3. Confirm that the choke valve has fully returned at
idling speed.
4. Check the idle speed. If necessary, turn the throt-
tle adjust screw and adjust the idle speed.
Idle speed
MTX: 800 ±s8 rpm (in neutral)
ATX: 950
Is8
rpm (in "N" range) F6
900 I58 rpm (in "N" range).. FE, F8
Idle Speed (Fl)
1. Connect the tachometer to the engine.
2. Check the idle speed.
Idle speed
MTX: 850 i!°0 rpm (in neutral)
ATX: 850 t55°o rpm (in "N" range)
3. If necessary, remove the blind cap from the throt-
tle body and adjust by turning the air adjust screw.
4. Install the blind cap.
76G01A-018
Idle Mixture (Carburetor)
1. Disconnect the secondary air hoses from the reed
valves and then plug the hoses (if equipped).
2. Connect an exhaust gas analyzer to the vehicle as
shown in the figure and measure the CO concen-
tration.
76G01A-106
3. Remove the blind cap from the mixture adjust
screw.
Note
The blind cap will be broken when it is re-
moved, do not attempt to reinstall it.
76G01A-019
1A—11