1987 MAZDA 626 oil pressure

OIL
COOLER AND
OIL
FILTER BODY 2B

OIL
COOLER AND
OIL
FILTER BODY
REMOVAL
1. Disconnect the battery negative cable.
2. Drain the engine oil and coolant.
3. Remove in the sequence shown in the figure.
76G02B-012
76G02B-013
1. Idler pulley
2. Water hose
3. Connector bolt
4. Oil cooler
5. Oil filter
6. Oil filter cover
7. Oil filter body
8. Plug
9. Pressure spring
10. Plunger control
11. Relief valve spring
12. Steel ball
INSPECTION
1. Inspect the oil cooler body for cracks or corrod-
ed. If necessary replace it.
2. Check the valves for damage or scoring if neces-
sary replace it.
3. Measure free length of each valve spring. If neces-
sary replace it.
Free length
Relief valve spring: 45.5 mm (1.79 in)
Pressure spring : 54.6 mm (2.15 in)
76G02B-014
2B-7

2B
OIL
COOLER AND
OIL
FILTER BODY
76G02B-015
76G02B-016
INSTALLATION
1. Apply a coat of engine oil to the valve holes.
2. Install the relief valve spring and pressure spring.
Tightening torque:
20—29 Nm (2.0—3.0 m-kg, 14—22 ft-lb)
3. Clean the contact surfaces of the cylinder block
and oil filter body.
4. Install new O-rings and apply a coat of engine oil.
5. Install the oil filter body.
Tightening torque:
Bolt A: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
Bolt B: 37—52 N-m
(3.8—5.3 m-kg, 27—38 ft-lb)
76G02B-017
6. Apply a coat of engine oil to the O-rings.
7. Install the oil cooler with new O-ring on the con-
nector bolt.
Tightening torque:
25—34 N-m (2.5—3.5 m-kg, 18—25 ft-lb)
8. Connect the water hoses.
9. Install the oil filter cover.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
10. Install the oil filter. (Refer to page 2B—6)
11. Install the idler pulley.
Tightening torque:
19—26 N-m (1.9—2.6 m-kg, 14—19 ft-lb)
12. Install the Comprex supercharger drive belt and
adjust the belt deflection. (Refer to page 1C—7)
13. Add specified amount of coolant and engine oil.
14. Check for leaks.
76G02B-018
2B—8

76G02B-031
76G02B-032
ASSEMBLY
Assemble the pump as follows.
Oil Seal
1. Apply engine oil to the pump body and the out-
side of the new oil seal. 2. Press in the oil seal.
Pressure Relief Valve
1. Install the plunger and spring in the pump body.
2. Install the spring seat plug and tighten to specifi-
cation.
Tightening torque:
26—39 N-m (2.7—4.0 m-kg, 20—29 ft-lb)
Outer and Inner Rotor
Install the rotors with the assembly mark facing the
pump cover.
Oil Pump Cover
1. Apply thread locking compound to the cover
mounting screws' threads.
2. Attach the oil pump cover to the body.
Tightening torque:
6—9 N-m (60—90 cm-kg, 52—78 in-lb)
76G02B-037
INSTALLATION
Install in the reverse order of removal referring to in-
stallation note.
Installation Note
Oil pump
1. Apply grease to a new O-ring and install it in the
oil pump body.
2. Apply silicon sealant to the shaded area as shown
in the figure.
3. Apply engine oil to the oil seal lip.
76G02B-033
2B-14

COOLANT 3A
76G03A-016
69G03A-006
COOLANT
INSPECTION
Coolant Level (Engine cold)
1. Check that the coolant level is near the radiator inlet
port.
2. Check that the coolant level in the coolant reser-
voir is between the FULL and LOW marks.
Add coolant if necessary.
Warning
a) Never remove the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
removing it.
Coolant Quality
1. Check that there is no build-up of rust or scales
around the radiator cap or radiator filler neck.
2. Check that coolant is free from oil.
3. Replace the coolant, if necessary.
Coolant Leakage
1. Connect a tester and SST to the radiator inlet port.
2. Apply 103 kPa (1.05 kg/cm2, 15 psi) pressure
to the system.
3. Check that the pressure is held.
If not, check for coolant leakage.
Warning
When removing either the radiator cap or the
tester, loosen it slowly until the pressure in
the radiator is released, and then remove it.
86U03X-005
REPLACEMENT
1. Remove the radiator cap and loosen the drain plug.
2. Drain the coolant into a suitable container.
Warning
a) Never open the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
loosening.
c) Use caution when draining hot coolant.
86U03X-006
3A-5

3B COOLANT
86U03X-004
69G03A-006
COOLANT
INSPECTION
Coolant Level (Engine cold)
1. Check that the coolant level is near the radiator inlet
port.
2. Check that the coolant level in the coolant reser-
voir is between the FULL and Low marks.
Add coolant if necessary.
Warning
a) Never remove the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
removing it.
Coolant Quality
1. Check that there is no build-up of rust or scales
around the radiator cap or radiator filler neck.
2. Check that coolant is free from oil.
3. Replace the coolant, if necessary.
Coolant Leakage
1. Connect a tester and SST to the radiator inlet port.
2. Apply 103 kPa (1.05 kg/cm2, 15 psi) pressure
to the system.
3. Check that the pressure is held.
If not, check for coolant leakage.
Warning
When removing either the radiator cap or the
tester, loosen it slowly until the pressure in
the radiator is released, and then remove it.
86U03X-005
REPLACEMENT
1. Remove the radiator cap and loosen the drain plug.
2. Drain the coolant into a suitable container.
Warning
a) Never open the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
loosening.
c) Use caution when draining hot coolant.
86U03X-006
3B—4

OUTLINE 4A
SPECIFICATIONS
F6 & F8 Engine
Engine F6 F8
Specification General Singapore General
ECE,
Hong Kong, &
Singapore

Idle speed
rpm
MTX 800
+58
Idle speed
rpm
ATX 950
t5§
(in N range)|
900 +5§ (in N
range)
CO concentration
%
2.0
± 0.5
(Without secondary
air
injection)

Carburetor

Type Down draft, two barrel
Throat diameter
mm (in)
Primary 30 (1.18) Throat diameter
mm (in)
Secondary 34 (1.34)
Venturi diameter
mm
(in) Primary 23.5 (0.93) Venturi diameter
mm
(in) Secondary 29.0 (1.14)
Main nozzle
mm (in)
Primary 2.6 (0.10) Main nozzle
mm (in)
Secondary 2.8 (0.11)
Main
jet mm (in)
Primary MTX 1.10 (0.0433) 1.09 (0.0429) 1.14 (0.045)
Main
jet mm (in)
Primary ATX 1.10 (0.0433) 1.08 (0.0425) 1.12 (0.044) Main
jet mm (in)

Secondary 1.50 (0.059)
Main
air
bleed mm (in)
Primary MTX 0.60 (0.024) 0.60 (0.024) 0.55 (0.022) Main
air
bleed mm (in)
Primary ATX 0.60 (0.024) 0.80 (0.031) 0.60 (0.024) Main
air
bleed mm (in) Secondary 0.50 (0.020)
Slow
jet mm (in)
Primary 0.48 (0.019) 0.46 (0.018) Slow
jet mm (in)
Secondary 1.00 (0.039) 1.10 (0.043)
Slow
air
bleed mm (in)
Primary No.1 0.80 (0.031)
Slow
air
bleed mm (in)
Primary No.2 1.90 (0.075) Slow
air
bleed mm (in) Secondary No.1 1.00 (0.039) 0.80 (0.031) Slow
air
bleed mm (in) Secondary No.2 0.50 (0.020)
Power
jet mm (in)
0.50 (0.0201
Fast idle adjustment
mm (in)

Clearance between
Drimarv
throttle valve and bore
1.40-1.76 (0.055—0.069) MTX: 0.48-0.64 (0.019-0.025) ATX: 0.56-0.72 (0.022-0.028)
Float level adjustment mm (in)
Max. fuel flow
"L"

Clearance between
flo

44 (17.3)
at and
air
horn without aasket Float level adjustment mm (in) Fuel stop
"H"
12.5(0.49)
Clearance between float and
air
horn without aasket; float lowered
by
own weight
Choke breaker diaphragm mmHg (inHg)
Start 180-240 (7.1—9.5) 100-160 (3.9—6.3) Choke breaker diaphragm mmHg (inHg) Stop 290-350 (11.4—13.8) 220—280 8.7—11.01
Choke opener mmHg (inHg) Start 35-65 (1.4-2.6)
...
35-65 (1.4-2.6) Choke opener mmHg (inHg) Stop
......
130-190 (5.1-7.5) 130-190 (5.1-7.5)

Fuel tank capacity
Liters (US gal, Imp gal) 60 (15.9, 13.2)

Fuel Dump

Delivery pressure kPa (kg/cm2,
psi)
20-26 (0.20-0.27, 2.8—3.8)
Feeding capacity cc/min (cu in/min) More than 860 (52.5)
at
idle

Fuel filter

Type Paper element with magnet

Air cleaner

Fresh-Hot switching Manual Diaphragm type
Element tvoe Oil permeated paper
Fuel specification Leaded regular

76G04A-513
4 A—15

4A OUTLINE
FE Engine
Engine FE 8Valve FE 12Valve FE 8Valve
Specification General Middle East
ECE, Hong Kong, & Singapore Unleaded fuel

Idle speed
rpm
MTX 800
+5§
850
+5§
Idle speed
rpm
ATX 900
+58 (in N
range)
CO concentration
%
2.0
± 0.5
(Without secondary
air
injection)

Carburetor

Type Down draft,
two
barrel
Throat diameter
mm (in)
Primary 30 (1.18) Throat diameter
mm (in)
Secondary 34 (1.34)
Venturi diameter
mm (in)
Primary 23.5 (0.93) Venturi diameter
mm (in)
Secondary 29.0 (1.14)
Main nozzle
mm (in)
Primary 2.6 (0.10) Main nozzle
mm (in)
Secondary 2.8 (0.11)
Main
jet mm (in)
Primary MTX 1.14 (0.045) 1.09 (0.0429) 1.14 (0.045) 1.09 (0.0429) Main
jet mm (in)
Primary ATX 1.12 (0.044) 1.08 (0.0425) 1.12 (0.044) 1.09 (0.0429) Main
jet mm (in)

Secondary 1.55 (0.061) 1.50 (0.059) 1.55 (0.061) 1.50 (0.059)
Main
air
bleed
mm (in)
Primary MTX 0.50 (0.020) 0.60(0.024) 0.50 (0.020) 0.50 (0.020) Main
air
bleed
mm (in)
Primary ATX 0.55 (0.022) 0.80 (0.031) 0.55 (0.022) 0.50 (0.020) Main
air
bleed
mm (in) Secondary 0.50 (0.020)
Slow
jet mm (in)

Primary 0.46 (0.018)
Slow
jet mm (in)
Secondary MTX 1.10 (0.043) 1.00 (0.039) 1.10 (0.043) 0.90 (0.035) Slow
jet mm (in)
Secondary ATX 1.10 (0.043) 1.00 (0.039) 1.10 (0.043) 1.00 (0.039)
Slow
air
bleed
mm (in)
Primary No.1 0.80 (0.031)
Slow
air
bleed
mm (in)
Primary No.2 1.90 (0.075) Slow
air
bleed
mm (in) Secondary No.1 0.80 (0.031) 1.00 (0.039) 0.80 (0.031) 1.00 (0.039)
Slow
air
bleed
mm (in) Secondary No.2 0.50 (0.020)
Power
jet mm (in)
MTX 0.50 (0.020) 0.50 (0.020) Power
jet mm (in)
ATX 0.50 (0.020) 0.40 (0.016)
Fast idle adjustment
mm (in)
Clearance between primary throttle valve and bore
MTX 0.48—0.64
(0.019-0.025) 1.40—1.76
(0.055-0.069)
0.48—0.64
(0.019-0.025) 1.40-1.76
(0.055-0.069)
Fast idle adjustment
mm (in)
Clearance between primary throttle valve and bore ATX 0.56-0.72 (0.022—0.028)
1.40—1.76
(0.055-0.069) 0.56-0.72 (0.022—0.028)
1.40-1.76
(0.055-0.069)
Float level adjust-
ment
mm (in)

Max. fuel flow
"L"

Clearance between
flo

44 (17.3)
at and
air
horn without aasket Float level adjust-
ment
mm (in)
Fuel stop
"H" |
12.5(0.49)
Clearance between float and
air
horn without aasket: float lowered
bv
own weiaht
Choke breaker diaphragm mm-Hg (in-Hg)
Start 100-160 (3.9—6.3) 180—240 (7.1-9.4) 100-160
(3.9-6.3)
180-240
(7.1-9.4) Choke breaker diaphragm mm-Hg (in-Hg) Stop 220—280
(8.7-11.0)
290-350
(11.4-13.8)
220—280
(8.7-11.0)
290-350
(11.4-13.8)
Choke opener mmHg (inHg)
Start 80—120
(3.1-8.7)
30-70 (1.2-2.8) Choke opener mmHg (inHg)
Stop 220-280 (8.7—11.0) 130-190
(5.1-7.5)

Fuel tank capacity
Liters (US aal, Imp aal) 60 (15.9, 13.2)

Fuel DumD

Delivery pressure kPa (kg/cm2,
psi)
20-26 (0.20—0.27, 2.8-3.8) 20-29 (0.20-0.30, 2.8-4.3)
20-26 (0.20-0.27, 2.8-3.8)
Feedina caDacitv cc/min
feu
in/mini More than 860 (52.5)
at
idle

Fuel filter

Type Paper element with magnet

Air cleaner

Fresh-Hot switchina Diaphragm Manual Diaphragm Bimetal
Element
tvDe
Oil permeated paper
Fuel specification Leaded super
Unleaded super Leaded regular Leaded super Unleaded super Unleaded regular

76G04G-514
4A—16

4B OUTLINE
SPECIFICATIONS
Item Specification

Idle speed rpm MTX: 800 +5„° (Neutral), ATX: 900 +5S
(P
range)

Throttle body

Type Horizontal draft (1 -barrel)
Throat diameter mm (in) 50 (2.0)

Air flow meter

E2-VS More than
20

E2-VC 100-300
Resistor
Q
E2-VB 200—400 Resistor
Q

E2-THA -20°C
(
—4°F) 13,600-18,400 20°C
(
68°F) 2,210-2,690 60°C (140°F)
493- 667
Air cleaner

Element type Oil permeated

Fuel pump

Type Impeller
(in
tank)
Output pressure kPa (kg/cm2,
psi)
441-588 (4.5-6.0, 64—85)
Feeding capacity cc (cu in)/10 sec. 220 (13.4) minmum

Fuel filter

Type Low pressure side Nylon element Type High pressure side Paper element

Pressure regulator

Type Diaphragm
Regulating pressure kPa (kg/cm2,
psi)
235-275 (2.4—2.8, 34—40)

Injector
TvDe
Hiqh-ohmic
Type
of
drive Voltage
Resistance
fi
12-16
Injection amount cc (cu
in) 15
seconds 38—53 (2.3-3.2)

Fuel tank

Capacity liters (US gal, Imp gal) 60 (15.9, 13.2)

Fuel

Soecification Unleaded reaular

76G04B-506
4B—6