1987 MAZDA 626 timing belt

DISASSEMBLY (TIMING BELT) 1 A
Mark the
direction of
rotation
76G01A-121
76G01A-122
*
/ V \
T^pJl/1
Disassembly Note
Crankshaft pulley
1. Set the SST against the flywheel.
2. Remove the crankshaft pulley.
Timing belt
1. Loosen the tensioner lock bolt, and remove the ten-
sioner spring.
2. Mark the timing belt rotation for proper reinstalla-
tion if it is reused.
3. Remove the timing belt.
Caution
Be careful not to allow oil or grease on the
belt.
Camshaft pulley
Remove the pulley lock bolt using a screw driver to
prevent the camshaft from turning.
76G01A-123
1A—39

INSPECTION AND REPAIR 1 A
Crankpin
,/f
Main journal
76G01A-132
5. If the diameter is less than the minimum, grind the
journals to match undersize bearings.
Undersize bearing: 0.25 mm (0.010 in),
0.50 mm (0.020 in), 0.75 mm (0.030 in)
Main journal diameter undersize mm (in)
Bearing size Journal diameter
025 (0.010)
undersize
No.1,2,4,5 59.693-59.711 (2.3501-2.3508) 025 (0.010)
undersize No.3 59.687-59.705 (2.3499-2.3506)
0.50 (0.020)
undersize
No.1,2,4,5 59.443-59.461 (2.3403—2.3410) 0.50 (0.020)
undersize No.3 59.437-59.455 (2.3400—2.3407)
0.75 (0.030) undersize
No.1,2,4,5 59.193-59.211 (2.3304-2.3311) 0.75 (0.030) undersize No.3 59.187-59.205 (2.3302-2.3309)
Rolled fillet
Crankpin journal diameter undersize mm (in)
Bearing size Journal diameter
0.25 (0.010) undersize 50.690—50.705 (1.9957-1.9963)
0.50 (0.020) undersize 50.440-50.455 (1.9858—1.9864)
0.75 (0.030) undersize 50.190-50.205 (1.9760-1.9766)
Caution
Do not grind the rolled fillet area.
76G01A-133
Main Bearing and Connecting Rod Bearing
Check the main bearings and the connecting rod
bearings for peeling, scoring, or other damage.
79G01C-077
Timing Belt
1. Replace the timing belt if there is any oil or grease
on it.
2. Check the timing belt for damage, wear, peeling,
cracks, or hardening. Replace if necessary.

86U01X-117

1A—60

INSPECTION AND REPAIR 1 A
Caution
a) Never forcefully twist, turn inside out, or
bend the timing belt.
b) Be careful not to allow oil or grease on the
belt.
86U01X-114
Timing Belt Tensioner and Idler Pulley
Check the timing belt tensioner and idler pulley for
smooth rotation and abnormal- noise. Replace if
necessary.
Caution
Do not clean the tensioner with cleaning
fluids. If necessary, use a soft rag to wipe it
clean, and avoid scratching it.
86U01X-115
Timing Belt Tensioner Spring
Check the free length of the tensioner spring. Replace
if necessary.
Free length: 56.9 mm (2.240 in) FE
64.1 mm (2.524 in) F8, F6
76G01A-134
Timing Belt Pulley and Camshaft Pulley
Inspect the pulley teeth for wear, deformation, or other
damage. Replace if necessary.
Caution
Do not clean the pulley with cleaning fluids.
If necessary, use a rag to wipe it clean.
Timing Belt Cover (lower and upper)
Inspect the timing belt covers for damage or cracks.
Replace if necessary.
86U01X-117
1A—61

1 A ASSEMBLY (TIMING BELT)
TIMING BELT
Torque Specifications
6—B N (1.25—1.75 m-kg, 109—152 in-lb)

1
A—82
69G01B-160

ASSEMBLY (TIMING BELT) 1 A
Camshaft Pulley
1. Install the camshaft pulley on the camshaft with the
dowel pin fit into the hole at the 2 mark (FE) or 3
mark (F8, F6).
76G01A-083
2. Tighten the camshaft pulley lock bolt.
Tightening torque:
47—65 N-m (4.8—6.6 m-kg, 35—48 ft-lb)
76G01A-141
3. Align the mating mark on the pulley with the align-
ment mark on the front housing.
Note
For FE engine, align "2" mark.
For F8, F6 engine, align "3" mark.
76G01A-084
Timing Belt Pulley
1. Reverse the direction of the SST (ring gear brake).
2. Install the crankshaft key.
3. Install the timing belt pulley on the crankshaft.
Tightening torque: 157—167 N-m
(16.0—17.0 m-kg, 116—123 ft-lb)
4. Release the ring gear brake.
5. Align the timing belt pulley and the pump body
alignment marks.
86U01X-160

1
A—83

1A ASSEMBLY (TIMING BELT)
Tensioner lock bolt
69G01B-165
76G01A-085
79G01C-097
Timing Belt Idler Pulley
Install the timing belt idler pulley.
Tightening torque:
37—52 Nm (3.8—5.3 m-kg, 27—38 ft-lb)
Timing Belt Tensioner
1. Install the timing belt tensioner and tensioner
spring.
2. Tentatively secure the tensioner with the spring fully
extended.
Timing Belt
1. Install the timing belt, (keep the tension side of belt
as tight as possible.)
Caution
a) If the timing belt is being reused, it must be
reinstalled to rotate in the original direction.
b) Check that there is no oil, grease, or dirt on
the timing belt.
2. Loosen the tensioner lock bolt.
3. Turn the crankshaft twice in the direction of rotation.
4. Check that the mating marks are correctly aligned.
If not aligned, remove the timing belt and tension-
er, and repeat the above-mentioned procedure.
5. Tighten the timing belt tensioner lock bolt.
Tightening torque:
37—52 Nm (3.8—5.3 m-kg, 27—38 ft-lb)
4BGQ1A-186
1A—84

ASSEMBLY (TIMING BELT) 1A
6. Check the timing belt deflection. If the deflection
is not correct, loosen the tensioner lock bolt and
repeat steps 3—5 above. Replace the tensioner
spring if necessary.
Belt deflection:
FE: 5.5—6.5 mm (0.22—0.26 in)
F8, F6: 4.0—5.0 mm (0.16—0.20 in)
/98 N (10kg, 22 lb)
76G01A-086
Baffle Plate
Position the baffle plate on the timing belt pulley.
Timing Belt Cover
Install the lower timing belt cover, upper timing belt
cover, and new gaskets.
Tightening torque:
7—10 Nm (70—100 cm-kg, 61—87 in-lb)
86U01X-163
Crankshaft Pulley
Install the crankshaft pulley.
Tightening torque: 12—17 N-m
(1.25—1.75 m-kg, 109—152 in-lb)
69G01B-170
76G01A-142
Valve Clearance (8-valve)
Adjust the valve clearance. (Refer to page
1
A—10.)
Cylinder Head Cover
1. Apply silicon sealant to the shaded areas shown
in the figure.
2. Install the cylinder head cover.
Tightening torque:
6—8 N-m (60—80 cm-kg, 52—69 in-lb)
1A—85

1
ENGINE
(DOHC)
OUTLINE 1B— 2
STRUCTURAL VIEW 1B— 2
SPECIFICATIONS 1B— 3
TROUBLESHOOTING GUIDE 1B— 3
TUNE-UP PROCEDURE IB— 5
ON-VEHICLE INSPECTION 1B—10
COMPRESSION 1B—10
ON-VEHICLE MAINTENANCE 1B—11
TIMING BELT 1B—11
CYLINDER HEAD 1B—16
REMOVAL 1B—22
DISASSEMBLY 1B—24
AUXILIARY PARTS 1B—24
TIMING BELT 1B—26
CYLINDER HEAD 1B—28
CYLINDER BLOCK 1B—30
INSPECTION AND REPAIR 1B—34
ASSEMBLY 1B—48
CYLINDER BLOCK 1B—48
CYLINDER HEAD 1B—59
TIMING BELT 1B—64
AUXILIARY PARTS 1B—68
INSTALLATION 1B—73
TRANSAXLE ASSEMBLY 1B—73
ENGINE INSTALLATION 1B—74
76G01B-001