INSTALLATION 1A
Connector Location
Install each harness as shown in the figure.
1. IG coil
2. Engine ground
3. Water temperature sensor
4. P/S switch
5. Oxygen sensor (Fl)
6. Water thermo switch
7. Injection harness (Fl)
8. F/l solenoid (Fl)
76G01A-146
9. Throttle position sensor (Fl)
10. Alternator
11. Oil pressure switch
12. Starter
13. P.T.C. heater (carb.)
14. Solenoid valve (Slow cot) (carb.)
15. Solenoid valve (carb.)
16. Transmission harness
1A—97
INSTALLATION 1B
Connector Location
Install each harness as shown in the figure.
76G01B-112
1. IG coil 10. Linear solenoid
2. Heat gauge unit 11. Solenoid valve (idle speed control)
3. Speed sensor 12. Throttle position sensor
4. P/S switch 13. Injection harness
5. Engine ground 14. Transmission harness
6. Water temperature sensor 15. Alternator
7. Water thermo switch 16. Oil pressure switch
8. Crank angle sensor 17. Starter
9. Oxygen sensor
1B-79
TROUBLESHOOTING GUIDE 7A
TROUBLESHOOTING GUIDE
Problem Possible cause Remedy Page
Change lever won't Seized change lever ball Replace 7A-58 shift smoothly, or is Seized change control rod joint Replace 7A-58
hard to shift Bent change control rod Replace 7A-58
Too much play in Worn change control rod bushing Replace 7A-58 change lever Weak spring of ball or change lever Replace 7A-58 Worn bushing of ball or change lever Replace 7A—58
Difficult to shift Bent change rod Replace 7A—58
No grease in transmission control Lubricate with grease 7A-58
Insufficient oil Add oil 7A-6
Deterioration of oil quality Replace with oil of 7A-6 specified quality
Wear or play of shift fork or shift rod Replace 7 A—18
Wear of synchronizer ring Replace 7A-27
Wear of synchronizer cone of gear Replace 7A-27
Bed contact of synchronizer ring and cone of Replace 7A-27 gear
Excessive longitudinal play of gears Replace 7A-22
Wear of bearing Adjust or replace 7A—22
Wear of synchronizer key spring Replace 7A-27
Excessive shaft gear bearing preload Adjust 7A-37
Improperly adjusted change guide plate Adjust 7A-20
Won't stay in gear Bent change control rod Replace 7A-58
Worn change control rod bushing Replace 7A-58
Weak change lever ball spring Replace 7A-58
Improperly installed extension bar Tighten 7A-58
Wear of shift fork Replace 7A—22
Wear of clutch hub Replace 7A-27
Worn clutch hub sleeve Replace 7A-27
Worn gear sliding part of both shaft gears Replace 7A-26
Worn gear sliding part of each gear Replace 7A-26
Worn steel sliding groove of control end Replace 7 A—18
Weak spring pressing against steel ball Replace 7A-18
Excessive thrust clearance Replace 7A—33,35
Worn bearing Replace 7A—22
Improperly installed engine mount Tighten 7A—49
Abnormal noise Insufficient oil Add oil 7A-6
Deterioration of oil quality Replace 7A-6
Worn bearing Adjust or replace 7A-22
Worn gear sliding surface of both shaft gears Replace 7A—26
Wear of sliding surfaces of gears Replace 7A-26
Excessive thrust clearance Replace 7A—33,35
Damaged gear teeth Replace with oil of 7A-26
specified quality Foreign material in gears Replace 7A-22
Damaged differential gear, or excessive backlash Adjust or replace 7A—30
76G07A-005
7A-5
TROUBLESHOOTING (G4A-EL) 7B
7. Perform the stall test for the following ranges in the same manner.
(1) D range (4) L range
(2) D range (Hold) (5) L range (Hold)
(3) S range (Hold)
Caution
Be sure to allow sufficient cooling time between each stall test.
Engine stall speed: D.S.L range 2170—2270 rpm
R range 2130—2230 rpm
Note
The stall test can be performed with the EC-AT Tester in place of a tachometer.
Drum stall speed indication: 0 rpm
76G0/B-029
Evaluation
Condition Possible cause
Above specification
In all ranges Insufficient line
pressure
Worn oil pump
Above specification
In all ranges Insufficient line
pressure Oil leakage from oil pump, control valve, and/or transmission case
Stuck pressure regulator valve
Above specification
In forward ranges Forward clutch slipping One-way clutch 1 slipping
Above specification
In D range One-way clutch 2 slipping
Above specification
In S (Hold) and L (Hold) ranges Coasting clutch slipping
Above specification In D (Hold) and S (Hold) ranges 2-4 brake band slipping Above specification
In R, L and L (Hold) ranges Low and reverse brake slipping
Above specification
In R range
Low and reverse brake slipping Reverse cluch slipping Perform road test to determine whether problem is low and reverse brake or reverse clutch
a) Engine brake applied in 1st ...Reverse clutch
b) Engine brake not applied in 1st ...Low and reverse brake
Within specification All shift control elements within transmission are func-
tioning normally.
Below specification
Engine out of tune
Below specification One-way clutch slipping within torque converter
86U07B-036
7B-29
30 TECHNICAL DATA
7A. MANUAL TRANSAXLE
Engine model FE DOHC Ffl FE FE
B
valve F8 Item —— Leaded UriBsded Ffl 12 valve Carb. Fl F8 RF-N RF-CX
Transmission
Shift
lever
position Floor shift
Gear ratio
First 3.307
Second 1.833
Third 1.310
Fourth 1.030
Fifth 0.837
1,233
0.970
0.795
0.914
1.161
0.861
0.755 0.680
Reverse 3.166
Oil capacity liters US qt, Imp
qt)
3.35 (3.6, 3.0)
Fluid type
ATF: DEXRON-II
Above 0°F: API GL-4
or
GL-5
SAE80W—90
or
SAE90
Clearance
Clearance
of
lever and reverse idle
gear
mm (in)
Standard 0.1—0.32 (0.004-0.013) Clearance
of
lever and reverse idle
gear
mm (in)
Wear limit 0.5 (0.020)
Clearance
of
shift fork and clutch hub sleeve
mm (in)
Standard 0.2—0.4 (0.008-0.016) Clearance
of
shift fork and clutch hub sleeve
mm (in)
Wear limit 0.5 (0.020)
Clearance
of
synchronizer ring
and
gear
mm
(in)
Standard 1.5 (0.059) Clearance
of
synchronizer ring
and
gear
mm
(in) Wear limit 0.8 (0.021)
Gear thrust clearance
mm (in)
First Standard 0.05—0.28 (0.002-0.011)
Gear thrust clearance
mm (in)
First Limit 0.3 (0.020)
Gear thrust clearance
mm (in)
Second Standard 0.18—0.46 (0.007-0.018)
Gear thrust clearance
mm (in)
Second Limit 0.5 (0.02) Gear thrust clearance
mm (in) Third Standard 0.05-0.20 (0.002-0.008)
Gear thrust clearance
mm (in) Third Limit 0.25 (0.010)
Gear thrust clearance
mm (in)
Fourth Standard 0.17—0.37 (0.0064—0.014)
Gear thrust clearance
mm (in)
Fourth Limit 0.4 (0.016)
Bearing preload
of
primary shaft gear
Primary shaft
0.1-0.25 N-m (1.0-2.5 cm-kg, 0.86-2.18 in-lb) Secondary shaft 0.2-0.4 N-m (2.0—4.0 cm-kg, 1.7-3.4 in-lb)
Bearing preload adjust shim mm (in) 0.25 (0.010), 0.30 (0.012), 0.35 (0.014), 0.40 (0.016), 0.45 (0.018), 0.50 (0.020), 0.55 (0.022), 0.60 (0.024), 0.65 (0.026), 0.70 (0.028), 0.75 (0.030), 0.80 (0.031)
Drive and differential
Final gear
TvDe
Reduction ratio
Side
bearina Dreload
Helical aear
4.1051 3.850 4.1051 3.850
4.150
1.4-2.0 N
m
(14—20 cm-kg, 12-17 in-lb)
Bearing preload adjust shim mm (in)
0.10 (0.004), 0.15 (0.006), 0.20 (0.008), 0.25 (0.010), 0.30 (0.012), 0.35 (0.014), 0.40 (0.016), 0.45 (0.018), 0.50 (0.020), 0.55 (0.022), 0.60 (0.024), 0.65 (0.026), 0.70 (0.028), 0.75 (0.030), 0.80 (0.031), 0.85 (0.033), 0.90 (0.035), 0.95 (0.037), 1.00 (0.039), 1.05 (0.041), 1.10 (0.043), 1.15 (0.045), 1.20 (0.047)
Backlash
of
side aear and
Dinion
aear mm (in) 0-0.1 (0-0.004)
30—26
