1987 MAZDA 626 timing belt

1 C ON-VEHICLE MAINTENANCE (TIMING BELT)
76G01C-020
76G01C-238
Kww
76G01C-021
Removal note
Timing belt
1. Aligh the timing marks of each pulleys.
2. Affix the injection pump pulley to the bracket us-
ing two bolts (35—40 mm, 1.4—1.6 in).
Caution
a) Do not turn in the reverse direction of en-
gine revolution.
b) After removing the timing belt, do not ro-
tate the crankshaft pulley or camshaft
pulley.
3. Make the forward direction arrow on the timing belt.
Note
Direction arrow is to reassemble the timing
belt in the same direction.
4. Loosen the timing belt tensioner bolt.
5. Shift the tensioner outwards as far as possible, and
temporarily tighten it.
6. Suspend the engine with chain block on the front
engine hanger.
7. Remove the No.3 engine mount.
8. Remove the timing belt.
Caution
Do not allow any oil or grease on the timing
belt.
Inspection and Repair
Inspect the following parts. (Refer to page 1C—60,
61).
1. Timing belt
2. Timing belt tensioner and spring
3. Timing belt idler pulley
4. Timing belt pulley
76G01C-022
1C—12

ON-VEHICLE MAINTENANCE (TIMING BELT) 1 C
Installation
Install in the reverse order of removal referring to the installation note.
Torque Specifications
85—117 N-m (8.7—11.9 m-kg, 63—86 ft-lb)
67—93 N-m (6.8—9.5 m-kg, 49—69 ft-lb)
37—52 N-m (3.8—5.3 m-kg, 27—38 ft-lb)
7—10 Nm (70—100 cm-kg, 61—87 In-lb)
11 N-m (80—110 m-kg, 69—95 ft-lb)
76G01C-239
Installation note
Timing belt
1. Check that the timing marks of camshaft pulley,
timing belt pulley and injection pump pulley align
with the timing marks.

76G01C-030

1C-13

ON-VEHICLE MAINTENANCE (TIMING BELT) 1 C
2. Install the timing belt tensioner and spring.
3. Temporarily secure the tensioner with it shifted
outwards.
63G01D-330
4. Install the timing belt.
Caution
a) The timing belt must be reinstalled in the
same direction of previous rotation, if it is
to be reused.
b) Be sure that there is no oil, grease, or dirt
on the timing belt.
76G01C-024
Install the idler pulley.
Tightening torque:
37—52
N
m (3.8—5.3 m-kg, 27-38 ft-lb)
Remove the affixing bolts from the injection pulley.
76G01C-025
7. Loosen the tensioner lock bolt.
8. Turn the crankshaft twice in the direction of rota-
tion (clockwise).
Caution
Do not rotate reverse direction.
9. Check that each timing mark is correcty aligned.
If not aligned, remove the timing belt. Repeat step
1-8.

76G01C-030

1C-14

ON-VEHICLE MAINTENANCE (TIMING BELT) 1 C
76G01C-027
76G01C-028
76G01C-029
Checking
point
Idler pulley
Crankshaft pulley zQi A/C
Checking point compressor
76G01C-030
10. Tighten the timing belt tensioner lock bolt.
Tightening torque:
37—52
N
m (3.8—5.3 m-kg, 27—38 ft-lb)
11. Check the timing belt tension.
If the tension is not correct, loosen the tensioner
lock bolt and repeat step 7—10, or replace the ten-
sioner spring.
Deflection: 9.0—11.5 mm
(0.35—0.45 in) /98 N (10 kg, 22 lb)
Caution
Be sure not to apply tension other than that
of the tensioner spring.
No.3 engine mount
Install the No.3 engine mount.
Tightening torque:
Nut A: 85—117 N-m
(8.7—11.9 m-kg, 63—86 ft-lb)
Nut B: 67—93 N-m
(6.8—9.5 m-kg, 49—69 ft-lb)
Drive belt
Install each drive belt, and check the belt deflection.
(Refer to page 1C—7.)
Steps after installation
Perform the necessary engine adjustment. (Refer to
TUNE-UP PROCEDURE,)
1C-15

1 C ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
CYLINDER HEAD
Removal
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-031
1. Accelerator cable
2. Air cleaner
3. Brake vacuum pipe
4. Intercooler pipe and hose*
5. Drive belt cover
6. Vacuum pump drive belt
7. Fuel hose
8. Water temperature switch
connector
9. Glow plug connector
10. Water thermo switch con-
nector
11. Heat gauge unit connector
12. Boost air temperature sen-
sor connector*
13. Injection pipes
14. Upper radiator hose
15. Water hose
(thermostat—FIR)
16. Oil level gauge and stay
bolt
17. Oil pipe bolt
18. Timing belt (Refer to page
1C—11)
19. Cylinder head cover
20. Camshaft pulley
21. Rear camshaft pulley
76G01C-032
22. Injection pump pulley
23. Seal plate
24. Water hose and pipe
25. Comprex supercharger
drive belt*
26. Heat insulator*
27. Exhaust manifold stay
28. Front exhaust pipe
29. Cylinder head bolt
30. Cylinder head
31. Cylinder head gasket
32. Comprex supercharger*
33. Exhaust manifold
34. Intake manifold
Note
* marked parts are equipped only for the RF-CX.
1C-16

1 C ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
76G01C-045
Gasket
Head cover Apply sealant
J
76G01C-046
76G01C-047
Timing marks
Timing marks
Timing
marks-
Injection pump pulley
1. Install the injection pump pulley with the semicir-
cular (woodruff) key to the injection pump shaft.
2. Rotate the injection pump pulley until the timing
marks are aligned.
3. Affix the injection pump pulley to the bracket us-
ing two bolts (35—40 mm, 1.4—1.6 in).
4. Tighten the lock nut.
Tightening torque:
59—69 Nm (6.0—7.0 m-kg, 43—51 ft-lb)
Cylinder head cover
1. Apply sealant to the shaded areas.
2. Install the cylinder head cover.
Tightening torque:
7—10
N
m (70—100 cm-kg, 61—87 in-lb)
3. Install the PCV hose.
Timing belt
1. Return the crankshaft about 45° to the timing mark
on the oil pump housing.
2. Check that the timing marks of the camshaft pul-
ley and the injection pump pulley align with the tim-
ing marks on the seal plate.
3. Install the timing belt. (Refer to TIMING BELT of
ON-VEHICLE MAINTENANCE)
76G01C-048
1C-22

1 C ON-VEHICLE MAINTENANCE (VALVE SEAL)
VALVE SEAL
Removal
1. Disconnect the negative battery cable.
2. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-052
76G01C-053
1. Cylinder head cover 7. Tappet and adjusting disc
2. Timing belt (Refer to page 1C—11) 8. Valve keeper
3. Camshaft pulley 9. Upper valve spring seat
4. Rear camshaft pulley 10. Valve spring
5. Camshaft cap 11. Lower valve spring seat
6. Camshaft and oil seal 12. Valve seal
1C—24

ON-VEHICLE MAINTENANCE (VALVE SEAL) 1 C
Removal note
Camshaft pulley
1. After removing the timing belt, turn the crankshaft
45° clockwise.
76G01C-054
2. Hold the camshaft with a wrench (29 mm, 1.14 in)
and loosen the camshaft pulley lock bolt.
Caution
Do not damage the cylinder head edge with
the wrench.
4BG01B-044
3. Separate the camshaft pulley from the camshaft
with the SST.
Caution
Do not hit the camshaft pulley with a hammer.
Rear camshaft pulley
Remove the rear camshaft pulley in the same man-
ner used for camshaft pulley.
76G01C-055
Camshaft cap
Loosen the camshaft nuts in two or three steps in the
order shown in the figure.

76G01C-066

1C—25